Search Documents

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower's control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower's stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower's pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By J. F. Abel

It can be concluded that rock mechanics instrumentation, geologic mapping, and operations research in combination will produce an accurate estimate of tunnel support requirements for establishing a steel-set load prediction model. This estimate can be used to increase safety and to reduce tunneling costs. Unnecessary supports can be eliminated; overloaded or insufficient supports can be replaced on a more scientific basis than previously possible. Only a limited number of measurements are required to develop a steel set load prediction model. The results of this study can be applied generally; but, every tunnel must be considered as a separate problem. The construction and geologic variables which were found to be significant in the prediction of rock loads in this tunnel were: steel section modulus, set blocking points, percentage of alteration, relative degree of faulting, relative water condition, distance to the nearest fault, and average joint spacing. INTRODUCTION A combined engineering geology and rock mechanics program was performed throughout the Straight Creek tunnel pilot bore in Colorado in order to develop a technique for estimation of steel tunnel support loads. The technique involves the construction of a statistical model from measured steel set loads, geologic and construction factors. The aim of the investigation was to produce a set of charts, based on these factors, which could be used by a trained man equipped with a hand lens and measuring tape, to specify a safe and economical steel size and set spacing. In order to be of practical value the measured parameters had to be rapidly measurable and capable of quantification. It was apparent from the beginning that quantitative values for many of the geologic factors would have to be arbitrary. It was impossible to ascertain in advance which of the readily determi-nable geologic and construction factors significantly affect steel set loading. As the investigation progressed the number of observations was systematically reduced in order to determine the minimum amount of data which would be necessary for a significant mathematical model. This paper presents an analysis of all the variables measured at each instrumented steel set. The statistical significance of the measured variables was determined. On the basis of this determination, a mathematical model was constructed and charts were prepared to select and space the steel tunnel supports at any given point in the tunnel. Once the effect of geologic and construction factors on set loading is sufficiently established, it is possible to exert close control over the selection of steel tunnel support size and spacing. The magnitude of this rock mechanics program can be appreciated when it is known that there were 44 instrumentation stations for which steel set loads were measured. For each of these sets there were three construction variables recorded, and nine geologic parameters determined (Table I). A rough approximation of the cost for both the collection and reduction of the data would be $50,000. This is in addition to the cost of geologic mapping.

Jan 1, 1967

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10, 1916 to Dec.10, 1916. BARNSDALL, THEODORE N., Treas. & Mgr., Highland Gas Co., 24 West Corydon. St., Bradford, Pa. BEASLEY, FRED E., Asst. Supt., Copper Refinery, Consolidated Mining & Smelting Co., Trail, B. C., Canada., BREWSTER, THOMAS T., Vice Pres., Gen. Mgr., Mt. Olive & Staunton Coal CO., 1012 Federal Reserve Bldg.,-St. Louis, Mo. BRINDLE ARTHUR ST. C.... Mining Recorder's Office, Trout Lake, B. C., Canada. BULLOCK, Harry E., Pres Kentucky-Jewel Coal Co., Lothair, Ky. BUTLER, PERCY BENNETT, Mine Operator :..P. 0. Box 335, Joplin, Mo. BUTLER, ROBERT S Supt., Three Johns Mining CO., ,Joplin,.Mo. CABOT, Godfrey, L., Carbon Black Maker, Gas Engr., 940 Old South Building Boston Mass.

Jan 1, 1917

By A. H. Shoemaker

THE shutdown of Homestake by Government order L-208, with its consequent disruption of a very stable and trained working force, coupled with postwar inflation and the coincidence that a mining depth had been reached that posed problems of ventilation, access to exploration areas, and choice of mining methods that would be applicable to zones of greater rock pressures made a very searching analysis of every phase of Homestake's operations a necessity. Any changes to be made had not only to meet the problems of deeper mining but also had to provide greater efficiency so that the mine might operate at a substantial profit until such time as a gold price adjustment might be forthcoming that would offset post-1945 inflation. Geology and Mining Situation The Homestake mine lies in the northern Black Hills in an area of Pre-Cambrian rocks exposed by the erosion of the paleozoic formations which covered the Black Hills. The Pre-Cambrian rocks in the vicinity of Lead comprise metamorphosed sediments with a total thickness of about 20,000 ft. The oldest formation, the Poorman, is ankeritic carbonate schist. The next oldest, the Homestake formation, host rock for all Homestake orebodies, is a siliceous iron-magnesium carbonate schist. The younger formations are dom-inantly argillaceous with some quartzites. Tertiary intrusive rocks cut all formations. The Pre-Cambrian rocks have undergone extreme isoclinal folding. Superimposed on this intricate folding are zones of shear folding which cross the isoclinal folds at small angles. The Homestake orebodies are pipelike replacements of the Pre-Cambrian Homestake formation where certain cross folds intersect some earlier isoclinal folds. These orebodies plunge flatly to the southeast at variable angles locally as steep as 45". The orebodies are replacement areas where numerous vein quartz of irregular shape have formed with surrounding zones of chlorite alterations containing disseminated sulfides and metallic gold. Where the numerous individual quartz veins with the sulfide and gold-bearing alteration zones are close together, large irregular orebodies with a roughly elliptical plan outline result. These ore zones may be more than 200 ft wide and 700 ft long in plan area. They have followed down the plunge of certain severely folded structures with great persistence. Two vertical operating shafts, the Ross and Yates, serve the mine, one with rope capacity to reach the 4850 level, the other to the 5000 level.

Jan 1, 1959

By J. Paone, S. Tandanand

This paper studies the behavior of rock at the initial state of crater formation resulting from stresses created under a drill bit. The purpose of this study is to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength or hardness of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous triaxial tests on Solenhofen limestone were adopted in establishing a limit of failure. Inelastic behavior of Solenhofen limestone was observed under a low velocity impact of a hemispherical bit and under static indentation with a similar bit. Permanent set at low applied loads in the indented area was measured with an interferometric technique. A quantitative determination of strengths of the rock was made under static indentation. The maximum yield strength estimated from the average stress over the contact area for plastic deformation was used as the crushing strength of rock under a drill bit. Much research has been done on energy requirements and mechanisms of energy dissipation to perfect rock fragmentation by a drilling process. But more needs to be done. More needs to be known about the mechanisms of energy dissipation or failure criteria of rocks in the drilling process in order to evaluate the efficiency of energy requirements in specific rock fragmentation. This paper examines some published studies on rock failure and energy dissipation and presents some findings in that phase of research concerned with rock fragmentation by drilling. This work is specifically concerned with rock behavior at an early stage of failure induced by a concentrated load. Consideration is limited to the primary phase of the crater formation under drill bit, i.e., before chipping takes place. Failure Phenomena of Rocks: Failure of rocks can be classified into two types, fracture and plastic flow. Both involve separation of material to form new surfaces with complete or partial loss of cohesion. Fracture is further classified as extension (or cleavage) fracture and shear fracture. Extension fracture involves separation in a plane without shear stress component, while shear fracture involves slippage along a plane as a result of combined stresses. Then, shear fracture inclines to the axes of the principal stresses. Plastic flow occurs under combined stresses, especially at high confining pressure and temperature, and denotes macroscopically irrecoverable deformation of rocks. Flow mechanisms have been classified as in-tergranular failure, intragranular gliding, and re-crystallization of mineral constituents.6 Failure phenomena in rocks are complicated because they include fractures and plastic flow as well as a friction process developed intrinsically as the internal stresses increase. All can occur in one rupture process, depending on the varying stress conditions. Both fracture and plastic flow are encountered in rock drilling. Rock failure under a drill bit as observed in drop tests simulating a single blow of a percussion drill, consists of two types, crushing and chipping. Crushing is considered as a separation of material particles by many fractures resulting from the application of high compressive stresses exceeding the strength of rock at the contact area. Chipping results from subsurface fractures extended to the face surface; this phase is preceded by crushing or surface deformation. The state of stress under the drill bit and the strength of rock create and control these two types of failure. The state of stress under the bit and in the vicinity of the contact area depend on the bit configuration and the magnitude of applied force. The strength of rock, characterized by its ability to resist penetration, depends on its composition and structure. However, the term "strength" quantitatively defined, is still ambiguous and may or may not correspond to the tensile, compressive and shear strength obtained from simple tests. Rock Failure Criterion: Rocks are weak in tension, their tensile strength being many times less than their compressive strength. This characteristic excludes

Jan 1, 1967

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

By Robert B. Sosman

THE chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily smaller. I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting on a paper that I had recently published27 on "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of Professor Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. SCOPE OF THE LECTURE During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyrometric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the United States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the "temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that "temperature of the furnace" is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1948

By Richard P. Rothwell

The anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 'to 30 feet thick. The system of mining employed is, almost without exception, that known as " chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because, not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By Nelson P. Hulst

To those who have had the happy privilege of friendship with George W. Goetz, the announcement of his death has brought great sadness. He was born in Milwaukee, Wisconsin, February 17, 1855, and died January 15, 1897. In his boyhood days, when I first came to know him, his frank, trustful manner; his eyes brimming with truthfulness; his eagerness, never obtrusive, to gain knowledge from all whom he met; and his equal readiness to give without ostentation of his store, constituted a personality which at once commanded confidence and won friendship. I am told that as a scholar of five years he was conspicuous for brightness, a show-pupil, who was called on to recite when visitors were present at school. Yet this in no way spoiled him. His modesty was too strong a trait in his character to be overcome by any attention which might, be expected to arouse vanity. In his simple-heartedness he was pleased then, as he always was in his maturer years, to give of his knowledge for the gratification of his listeners, with never a thought of himself. So strong was this characteristic that in a brief autobiography, in the form of a letter to his wife and children, found among his papers, he excuses himself to them for recounting what he had accomplished in his life-work. As a preface to this autobiography (which, it seems, was prepared on the eve of a sudden journey to California, taken February, 1895, for his health) he says: " I am writing this rather hastily, and I

Jan 1, 1898

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

Jan 1, 1949

By Oswald J. Heinrich

During the last twenty years much has been done to investigate and define the Mesozoic formatibn of the United States along the Atlantic States, as well as in' the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geologicd surveys of Penn-

Jan 1, 1879

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack-poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet-for indeed the instrument is easier levelled, and, more-over, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity ; on the other hand, however, that correction

Jan 1, 1873

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope ; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet for indeed the instrument is easier levelled, and, moreover, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure Any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity; on the other hand, however, that correction

By Manuel Eissler

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

By Everett M. White

Numerous articles have been written in regard to the man who mines coal and he has been likened to brave men in all ages who have gone out to conquer some unknown hazard. Now, however, modern mining is no longer something to be avoided but is a vocation that anyone can well be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operator of most mines as well as the state and Federal inspectors to see that coal mines are as safe or safer than any other industry. However, it is true that mine fires and explosions have occurred in the mining industry since its earliest inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England, which resulted in the death of 69 persons in August 1708. It is interesting to note that he states, "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." From this statement it is noted that women were employed as miners in England during that period. Numerous mine fires and explosions have occurred in mines in this and other countries. Several of them claimed more than 100 lives. Among the greatest losses was a mine explosion in West Virginia that claimed 361 and a mine fire in Illinois that claimed 259. Although no one would minimize the seriousness of a mine fire or an explosion, yet in too many cases they have been publicized out of proportion. This especially is so when compared with the accident rate of other industries or on our highways. It should be remembered that of these general classifications of hazards in mining, mine fires and explosions rank very low in the accident rate in any given year. In modern times the coal industry has completed two years or more, at various times, without a single major disaster. The

Jan 1, 1973

By Edward Halse

THE occasional occurrence in metalliferous veins of rounded fragments of rock, matrix or ore, lying loose, embedded in clay, or enclosed in some kind of cement, may be attributed to four causes:¬ I. They have been washed in from the surface, or from an upper portion of the vein. II. They are of concretionary origin. III. They have been produced by movements in the country-rock or in the walls of the vein. IV. They have been found in situ, by the upward, downward or lateral flow of water in the vein itself. In this paper the word " conglomerate " is confined to a rock composed of rounded fragments or pebbles cemented together, as distinguished from a " breccia," in which the rock-fragments are angular. I. BOULDERS AND PEBBLES WHICH HAVE BEEN WASHED IN FROM THE SURFACE, OR FROM AN UPPER PORTION OF THE VEIN. In this type it is presupposed that the vein at onetime com¬municated by a fissure or open space with the surface, or with the upper portion from whence the fragments have been washed. One well-authenticated occurrence was described long ago by Fournet. Owing, no doubt, to later dislocations in the lode, pebbles from an old alluvium and sands containing titaniferous iron, as well as fragments of wood, were found in a vein at Huelgoët, in France. "Toutes les parties tendres du filon de Pranal ou ces pédnomènes sont les plus prononcés ont été excavés jusqu'a d'assez grandee profondeurs par l'impétuosité des torrents, qui ont deposé la matière alluviale."1

Jul 1, 1905