Search Documents

By Walter H. Bruckner, George B. Clark

SINCE the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained e1sewhere.l,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established concerning cavity liners: 1,2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as on the base diameter of the charge. Acute apex angles require thinner walls for optimum performance and more obtuse angles require thicker walls for the same base diameter. 2. Cones were more effective in forming a penetrating jet when the walls were tapered; i.e., the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical proper- ties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of Slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2. Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1947

By R. E. Zimmerman, Michael Sokaski, E. R. Palowitch, M. R. Geer, H. F. Yancey, W. Deurbrouck, S. C. Sun

PART 1: DENSE MEDIUM SEPARATION by M. SOKASKI, M. R. GEER and H. F. YANCEY INTRODUCTION In the early days of coarse-coal treatment by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken :he loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War 11 in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-ton-per-hour pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London. In April 1945,2 operation of this pilot plant was observed by one of the authors, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was started by the Bureau of Mines immediately. This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals was made available. Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are so easy to clean they respond well to simpler cleaning systems, the first cyclone plant was not built until 1961.3 As of the spring of 1967, a total of 31 commercial cy- clone plants had been installed or were under construction in the United States; this does not include eight Dynawhirlpool plants. The capacity of the cyclone plants ranges from 50 to 1300 tons per hour and totals 6600. THEORY Before discussing the theory of a dense medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in figure 10-1, the mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vertical flow. The refuse moves along the wall of the cyclone and is discharged through the under- flow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the vortex finder to the overflow chamber.

Jan 1, 1968

By Samuel B. Christy

" The man is always greater than his work." The training of the men who are to develop the mineral resources of the world is the most important problem connected with mining engineering. It becomes ever more important to civilization as the mineral wealth of the earth approaches exhaustion. I have therefore decided to consider a few of the more important problems arising in the training of the mining engineer, and especially those arising in America. , The Peculiar Nature of Mineral Wealth. Mining and Agriculture are the two fundamental arts. Without the latter our existence would be precarious; without the former, our civilization impossible. Agriculture furnishes that regular supply of food and raiment which leads to the growth of large communities in which cultivated leisure first becomes possible; while mining furnishes the metallic thread from which is woven that complex fabric we call civilization. But in these two arts the conditions for success are widely different. Most of the crops that the farmer reaps may be harvested year after year, and the proper fertilizers being added, he may continue the annual harvest indefinitely, while, as a result of cultivation, his farm becomes yearly more valuable. But the crop the miner reaps can be harvested but once in the history of the race. Our mineral wealth has taken unknown ages to mature in the bosom of the earth. The ripened fruit can be plucked but once. There are no fertilizers for worked-out mines. It never pays to work over a mine that has been

Jan 1, 1906

By Nathan C. Rockwood

LIME is a very general term applied to products of limestone, in popular treatises often incorrectly, including ground or pulverized limestone used in agriculture. When used without qualifying adjective, the term usually means burned or calcined limestone, or quicklime, or calcia. The corresponding calcined product of magnesite is magnesia. If the calcined rock is relatively pure calcium carbonate, the resulting lime is a "high-calcium" lime; if the rock is dolomite, or a combination of calcium and magnesium carbonates, the lime is a "dolomitic" or a "high- magnesium" lime. There are various grades in between, depending on the percentage of magnesium carbonate and other ingredients in the raw rock. For some industrial purposes only high-calcium limes are suitable; in other processing-as, for example, neutralizing acid wastes -the relative percentages of magnesium and calcium carbonates in the raw material are not important. Limestone is burned (roasted or calcined) in furnaces known as lime kilns by direct exposure to the hot gases and flames. When heated to incandescence, the carbon dioxide content of the rock is expelled, leaving calcium and magnesium oxides, according to the formula usually written: [ ] This thermal reaction is reversible, which requires that the lime be withdrawn from the "calcining zone" of the kiln about as fast as made. Pure calcium carbonate would lose 44 pct of its weight in the calcining process; dolomite, 48 pct. Generally, the lime will retain the approximate size and shape of the piece of rock from which it is made but some few limestones tend to break down into granules or dust. Hence lime (quicklime) comes from the kilns in lumps or granules and normally is packed in water- tight containers in these forms, or is pulverized after calcination.

Jan 1, 1949

By J. P. Doan, G. Ansel

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By H. H. Campbell

Many attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits—a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It mag be urged that the microscopic structure must betaken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all testrpieces be made under the same conditions; and it is believed that the tests described in this paper satisfy that requirement. The investigations were made at the works of the Pennsylvania Steel Company, Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham-

Jan 1, 1905

By G. R. Wilms

A study has been made of the structural changes in polycrystalline high purity aluminum during the tertiary stage of creep under conditions of constant tensile load. It appears that there is no basic modification in the particular mechanism of deformation that characterized the preceding secondary stage of creep, but that the changes in crystalline structure produced during the tertiary stage are only a consequence and not a cause of the accelerated strain. Intercrystalline fissures were observed on entry into the tertiary stage, and these might supplement the accelerated rate of strain owing to local stress concentrations. There is evidence that the formation of these fissures may be associated with the presence of surface imperfections, and it is suggested that a more generalized treatment of the results may explain certain creep characteristics of commercial alloys. IN previous work'-4 a study was made of the changes produced when specimens of annealed aluminum were deformed at various temperatures and rates of strain, especially under conditions leading to creep under constant tensile load. It was shown that, as the temperature was increased or as the rate of strain was decreased, elements of the substructure produced within the grains became coarser, and with the strain rate constant at a given temperature, their size tended to an equilibrium value. The preliminary process of the breaking down of the grains into a substructure was identified with primary creep.' The subsequent equilibrium, condition was associated with secondary creep. The question then arose whether the tertiary stage corresponded to any further significant change in the substructure. The question is also of interest in view of the opinion, expressed for instance by Andrade,5 that the tertiary stage is merely an accelerated rate of strain due to the reduced area of section of a specimen under continuous tensile load, and the other opinion, as suggested by the observation by Sully, Cale, and Willoughby6 of a tertiary stage in com-pressive loading, that this third stage is a real effect in its own right. The object of this paper is to record some observations on the tertiary stage of high purity aluminum. Experimental Procedure The material was aluminum of 99.98 pct purity as previously used. The specimens had a rectangular section of l/8 x l/2 in., and extensions were measured over a 1 in. gage length. After machining to shape, the specimens were annealed to give a standard grain size of 0.2 mm and then electropolished. The general procedure involved metallographic and X-ray diffraction examination at progressive stages of elongation (marked by arrows on the curves shown in Figs. 1 and 2), the specimen being extended to fracture under constant load at a given temperature. The X-ray tests were made by the back-reflection method from a stationary specimen, using CoK radiation. The longer edge of the micrographs in the paper corresponds to the direction of applied stress. Results The previous work showed that, in the secondary stage of creep in aluminum, three basic types of structure could be developed according to the temperature and rate of strain. These were: 1—slip, which predominated at the lower temperatures and higher rates of strain and produced the finest and least perfect substructure; 2—cell structure, which superseded slip as the temperature was raised and the rate of strain decreased and which was characterized by a coarser and more perfect structure and an absence of slip lines; and 3—a stage termed "boundary microflow," which predominated at still higher temperatures and lower rates of strain when the cell size had increased and become comparable

Jan 1, 1955

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

Jan 1, 1892

SLAG composition, slag constitution, reactions in slag, and reactions between slag and metal-in other words, the physical chemistry of slags-are matters of great importance to the open-hearth operator, whether or not he makes use of any detailed knowledge of them. Although this is a relatively young branch of the science of steel- making, much progress has been made; however, much remains to be learned, and many of the statements that can be made at present are probably--or even certainly-subject to future change. Nevertheless, the physical chemistry of slags is sufficiently developed to provide a reasonably secure basis for real understanding of steelmaking reactions. FUNDAMENTALS OF SLAG CONTROL By way of introduction, some time is spent in this chapter on effecting an easy transition from some of the more "practical" manifestations of slag to discussions couched in the more formal language of physical chemistry. This necessitates a certain amount of repetition, but it is felt that the purpose of the chapter is best served in this way. Reactions in the metal phase have products that find their way into the slag and are important components thereof; they are discussed in detail in the preceding chapter. Some substances distribute themselves Between slag and metal in definite fashion, and others are found only in the slag. Their reactions are a large reason for this chapter. Limitations of Slag Control. The open-hearth process is essentially oxidizing and cannot be otherwise operated. (Oxygen gradients in the furnace, the mechanism of oxygen inflow, and similar subjects are discussed in Chapter XIX.) As shown in the calculations of material and heat balances for the charge (see Chapter XV), from 25 to 50 lb. of oxygen will flow from air or combustion gases into the charge or molten bath during the heat for each ton of liquid steel

Jan 1, 1944

By J. V. Emmons

It has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass.

Jan 1, 1915

By Galen G. Waddell

Several years of rock-burst research conducted by the U.S. Bureau of Mines in cooperation with the mining companies of the Coeur d'Alene mining district, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem. A rock burst is the sudden, violent release of stored strain energy in rock by some mechanism of rock failure, generally accompanied by expulsion of rock with consequent damage to the mine. A burst may be audible for only a few hundred feet, or on the surface it may sound like a sonic boom miles away. A Dictionary of Mining, Mineral, and Related Terms, U.S. Bureau of Mines (USBM)* 1968yand defines a burst as Bureau "That phenomenon which occurs when a volume of rock is strained beyond the elastic limit and the accompanying failure is of such a nature that accumulated energy

Jan 1, 1971

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By Gary E. Parish

TABLE OF CONTENTS Contents I. Introduction II. Purpose of the Paper III. Historical Perspective A. Existing Sources B. New Sources (NSPS) C. Hazardous Pollutants (NESHAPS) D. Enforcement/Judicial Review 1. Title I Enforcement 2. Title III Enforcement 3. Information Gathering E. Summary IV. The Clean Air Act Amendments of 1977 (1977 Act) A. SIP-Related Provisions 1. Section 107(d) - Geographic Boundaries 2. Section 108 - Air Quality Criteria 3. Section 109 – NAAQS 4. Section 110 – SIPs 5. Section 122 and Sections 402 and 403 of P.L 95-95 – Unregulated Pollutants 6. Emission Offsets – Interpretive Ruling (I.R.) B. PSD Provisions - Part C. 1. Regulations Under the 1970 Act 2. The 1977 Act 3. Regulations Under the 1977 Act C. Visibility Protection - Part C, Subpart 2 D. Non-Attainment Provisions - Part D E. Monitoring and Modeling F. NSPS G. NESHAPS H. Enforcement/Judicial Review 1. Title I 2. Economic Enforcement 3. Title III Enforcement/Judicial Review (a) Section 304 (b) Section 307 4. Summary V. Special Problems and Opportunities for the Uranium Industry A. End Use B. Transportation C. Milling/Processing D. Extraction E. Exploration/Discovery F. General VI. Conclusions Appendix A Footnotes

Jan 1, 1979

By P. Pollard

A method has been developed for evaluating acid treatments in fractured limestone fields by breaking down pressure drawdown into three component parts: (I) pressure differcntial across "skin" near the borehole face, (2) pressure differential due to flow resistance in the coarse communicating fissures and (3) pressure differential between the fine voids and the coarse fissures. It is apparent that in most successful acid treatments the first term, skin resistance, has been reduced or eliminated. Further, it is often possible to estimate the volume of coarse fissures associated with the second term, coarse fissure flow resistance. In cases where this volume is comparable with practical acid volumes it seems likely that this resistance also may be attacked with a suitably retarded acid. INTROD UCTION Acid treatment has been successfully applied as a general practice in the limestone wells in the Mara/ Maracaibo districts of Venezuela for some 10 years. At the same time the need has been felt for a more precise method of: (1) evaluating the effect of an acid job and (2) selecting wells which should benefit from an acid treatment. The following method, based on an analysis of build-up curves for wells producing from fractured limestone, provides a means of forecasting the effect acid will have on a well and in many cases the probable order of production rate increase which may be expected. In certain cases it is also possible to calculate the fissure volume through which the acid has to be displaced for best results. Various approximations are introduced in the method, but within the limitations of these the analysis gives an indication of how a well, whether previously acidized or not, may be expected to respond to acid treatment. Suitable build-up curves cannot be obtained on "tight" wells which do not give sustained production and the method is not applicable to such wells. Figs. 1 through 7 illustrate various types of build-up curves obtained from limestone wells in Western Venezuela. Curves are included showing (1) both skin and coarse fissure resistance, (2) skin resistance only, (3 and 4) reduction of skin resistance by acidization, (5) fissure resistance only, (6) reduction of coarse fissure resistance by acidization, and (7) acidization failure. This theory has been successfully applied for over three years during which 22 acid treatments have been carried out specifically to reduce skin resistance and three treatments to reduce coarse fissure resistance. The method has been found to be a useful aid in the selection of wells for acidization.

By M. Baeyertz

SINCE 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer1, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallography. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types.

Jan 1, 1930

NORTH AMERICA. CANADA Canadian Army Overseas. Ball, H. D. Bridges. C. Butterill, H. J. If. Ladner, F. E. Lane, H. C. Alillar, W. A. ALBERTA Calgary.-Chonette, W. C. Clark, L. At. Corbett, C. S. de Hart, J. B. Dingman, C. W. Fath. A. E. Fulton. J. If. Cray, J. G. Johnson. R. V. McCutchin, J. A. *Slipper, S. E. Vin Buckirk H. A.

Jan 1, 1944

By H. A. Tobelmann

age Introduction ............................. 22 Crushing............................... 25 Leaching............................... 28 .Reduction.............................. 47 Electrolytic Deposition..............a.......... 51 Discard for Purification of Electrolyte.................. 60 Recovery of Copper from Discard Solution .............. 62 Resolution of Cement Copper...................... 64 Summary............................... 64 Appendix............................... 66 Discussion............................... 69 Introduction The location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the discussions thereof.l It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 11 mo. In all about 15,000 T. of ore were treated experiment-

Jan 1, 1919