Search Documents

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:' I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By Y. C. Kim, C. B. Manula

This paper is concerned with the details of the derivation of an operations research model, specifically linear programming, to solve production scheduling problems. While some results are presented for an actual study, the calculation of cases of a more general nature have not yet been completed. Production managers from those segments of the mining industry that experience a seasonal or highly variable sales demand find it rather difficult to develop overall producing plans for their organizations. In an attempt to solve this technical problem, demands are usually met by keeping production corresponding exactly to sales. This results in a fluctuating production schedule which is costly to maintain because of overtime premiums in periods of high requirements and because of costs associated with an idle mine plant during slack periods. An alternate solution may be to produce part of the desired amount and make up any deficiencies by using overproduction in previous time periods. This tends to smooth the production pattern through the use of a stockpile. However, because of associated storage costs, the solution may again be undesirable if it yields comparatively large surpluses. In general, this type of scheduling problem has an infinite number of solutions which satisfy the requirements. These are largely dependent on the extent to which an operation is geared to changes in production and on the size of its stockpiling facility. The determination of an efficient schedule is implied, therefore, as one lying between two extreme solutions, i.e., one that minimizes surpluses and one that minimizes output fluctuations. These conflicting objectives result in an economic balance problem between the costs of carrying surpluses forward from slack periods versus the cost of high production levels during peak demands. Various methods of operations research have been developed to handle problems whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. Those who are familiar with mining operations know that most managers have not progressed satisfactorily in this area. Production planning systems which most mines employ today are often no more than rough records of management's mental planning. For small mines these means are normally sufficient; but as operations grow larger and become more complex, this type of planning ability is no longer adequate. Managers may find themselves losing control of cost relationships, taking longer to outline production sequences, and becoming forgetful of certain resource availabilities. ORIGIN AND SCOPE OF A SCHEDULING PROBLEM The more fundamental aspects of the production scheduling problem can be brought into focus by demonstrating how it exists in a bituminous coal mine* located in southwestern Pennsylvania. This mine, operating in the Pittsburgh seam, uses a definite room-and-pillar block system of mining, which is planned and carried out with only slight variations to meet local conditions. The coal seam, which is firm and varying in thickness from 8 to 9 ft with the bottom 6% ft being extracted, is under 500 ft of cover and opened by a shaft. The bulk of the coal (60%) is obtained from the pillaring activity with the mains and sections, which are considered primarily as development activities, contributing the balance of 12% and 28%, respectively. All coal is won by a ripper-type continuous miner in conjunction with shuttle-cars directly behind a loading machine. Track haulage is employed to move coal from these machine centers to the shaft bottom. The coal, thus mined, is shipped to one destination as part of a mixture of coals to be used in the making of steel. A material flow diagram of this distribution scheme is illustrated in Fig. 1. PROBLEM STATEMENT From the above types of shipments and mining limitations, the basic problem is to determine an economic means of producing and stockpiling a single coal product produced in three different machine centers (main, section, and pillar). Fig. 2 shows total demand for coal as a function of time. Because of the extremely high peak demands, slack period production must be stored and then distributed

Jan 1, 1969

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,' kinetics,2'3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6'7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969

By Jei Y. Choi, Paul G. Shewmon

The surface self-diffusion coefficient of copper (D,) has been measured between 847° and 1069 "C for six different orientations. These were the(111), (110, (100, and three higher index surfaces. The activation energy for Ds (designated Q s) was found to be about 49 kcal per mol for all six surfaces, and Do about 2 x 104 sq cm per sec. At any temperature Ds varied by no more than a factor of three over these orientations. It is shown that, if the free energy of a surface atom is uniquely determined by its number of nearest neighbors, it follows from the Principle of microscopic reversibility that Qs should have the same value for all surface orientations, and Ds should vary little with orientation. This model also suggests that for clean fee metals Qs ~ 2/3 AH, (heat of vaporization). This is true for copper. ALTHOUGH it has been appreciated for several decades that atoms can diffuse more rapidly on a surface than through the bulk of a crystal, it has only been in the last few years that reliable values of the surface self-diffusion coefficient (Ds) have become available. Tracer studies of Ds had been attempted prior to this period, but when a tracer is placed on a surface, an ever increasing fraction of it is drained off into the lattice. The correction for this loss involves a very difficult, and as yet unperformed calculation. Those who have worked with tracers have not corrected for this loss.1, 2 Thus their results indicate that Ds is greater than the self-diffusion coefficient in the lattice (Dl), but it has not been established that they give quantitative data on Ds. A procedure which avoids the problem of tracer loss is to study the rate of mass-transfer under the effect of surface tension. If the surface asperity being studied is very small, the mass transfer occurs entirely by surface diffusion. The kinetics at which a grain boundary groove forms on an initially plane surface is a well-studied case of this type. The smoothing of a slight scratch in an otherwise flat surface is another procedure that has been studied. If these grooves are up to 20 to 30 µ in width, the dominant mechanism for mass transfer is surface diffusion (at least in the case of metals with low vapor pressures), and the widths can easily be measured with an interference microscope. Of these two, mass-transfer techniques only in the case of grain boundary grooving has a rigorous mathematical treatment been given. This was done by Mullins.3,4 His analysis predicted that in the case of copper in an atmosphere of an inert gas, surface diffusion should be the dominant transport mechanism. This analysis gave an equation for the groove profile and predicted that the width of the groove would increase as (time)1/4. Mullins and Shewmon showed that both of these predictions agreed with experiments.5 Thus the validity of the values of Ds given by this procedure seems to be well established. Gjostein has used copper bicrystals and the grain boundary grooving technique to determine Ds and the activation energy for surface selfdiffusion (9,) in the [001] direction on surfaces ranging between the (100) and (110) planes.= He reported that Qs = 41 kcal per mole and Do = 6.5 x 102 sq cm per sec for all orientations studied. Since the results did not change with the dew-point of the dry hydrogen atmosphere or the type of refractory tube used, he concluded that the surfaces were clean, or at least that the results were not influenced by any impurities chemisorbed from the atmosphere. The work reported here reproduces and extends Gjostein's study in that D s and Q s were determined for copper over a wider range of orientations. To study the effects of impurities, two purities of copper were used as well as cathodic etching to remove any possible electropolishing film. Gjostein postulated that the diffusing atoms on a surface near a low index plane are the few atoms which are adsorbed on the smooth region between ledges or steps in the surface. A more rigorous derivation of the equation relating Ds to the concentration and jump frequency of these adsorbed atoms is given here. Using this treatment, our empirical observation that Q s and D s are essentially the same for all surface orientations can be shown to follow from the assumption that the free energy of a surface atom is uniquely determined by its number of nearest neighbors. The studies of D s using the scratch technique have been carried out by Blakely and Mukura on nickel,' and by Geguzin and Oveharenko on copper. The latter study using copper gives values of D s roughly

Jan 1, 1962

By A. S. Nowick, C. Y. Li

It is deMonstrated that quenching from an elevated temperataupe accelerates the grain boundary relaxation in two solid solutions (aAg-Zn and a Cu-Al). This result is consistent with the proposal that, in solid solutions, grain boundary relaxation occurs by a mechanism of' self diffusion. Nevertheless, an alternative possibilitg, that quenching introduces vacancies into the boundary itself, must also be considered. THE phcnomenon of grain boundary relaxation has been well known for many years,1,2 yet the mechanism of this process is very poorly understood. One of the most interesting suggestions which relates to the mechanism of grain boundary relaxation was that of Ke,3 who claimed that the activation energy for grain boundary relaxation and for lattice self diffusion were essentially the same. The implication is therefore that the elementary step in the two processes is the same. This suggestion is particularly startling in view of the fact that activation energy for self diffusion along a grain boundary is very significantly lower than that for volume self-diffusion. Later evidence5-7 showed that there really are two grain boundary peaks, one which appears in high-purity metals, and the other (which develops at a higher temperature than the first) which appears in solid solutions beginning at solute concentrations in the range of 0.1 pct. Data for silver6 show that Kg's hypothesis is surely incorrect for the grain boundary peak in the high-purity metal, since it has an activation energy of only 22 kcal per mole, but that the hypothesis may still be correct for the grain boundary peak in various silver solid solutions, for which activation energies in the range 40 to 50 kcal per mole are observed. If the elementary step in the grain boundary relaxation process were the same as that for self-diffusion, it would be expected that the relaxation process could be hastened by quenching, 2.c. by introducing a non-equilibrium excess of lattice vacancies. Such a quenching effect has already been demonstrated in the case of another anelastic relaxation process, viz., the Zener relaxation effect. The Zener effect, which occurs in essentially all solid solutions, may be attributed to the reorientation of pairs of solute atoms in the presence of an applied shear stress,' and therefore must take place by means of a volume diffusion mechanism. The hastening of this process through quenching9 has been one way of demonstrating that atom movements in the lattice take place through a defect mechanism, presumably single vacancies. In order to see if the grain boundary relaxation is affected by quenching, it is particularly convenient to compare the grain boundary relaxation with the Zener effect, by choosing a specimen for which both relaxation effects appear. Specifically, a fine-grained sample of a solid solution shows in the curve of internal friction vs temperature, first a peak due to the Zener effect, then a second rise (and eventually a peak at substantially higher temperatures) due to the grain boundary relaxation. The same phenomena are also observable in static anelastic measurements, such as creep at very low stress levels. Thus, for the same fine-grained solid solution, the creepstrain, when plotted against log time, falls on a sigmodial curve with a sharp inflection point, due to the Zener effect, which is followed by a second rise and inflection resulting from the grain boundary relaxation. To look for a quenching effect, static measurements are preferable to the dynamic internal friction measurements, due to the fact that quenching effects tend to anneal out too rapidly at the temperatures at which the internal friction is measured.9 RESULTS AND DISCUSSION Creep experiments in torsion were carried out in an apparatus similar to that described by Ke1, whereby a wire is held under constant torque and its angular displacement is observed as a function of time. The alloy Ag-30 at. pct Znwas selected because of the large Zener relaxation that it displays. The two samples used were a "coarse grained" wire with a mean grain size about twice the diameter of the wire (diam = 0.032 in.), and a "fine-grained" wire which had several grains across the diameter. In Fig. 1 a comparison is made of the creep curves at 160°C of these two samples after they had been cooled slowly from 400°C. Curve A, which represents the coarsegrained sample, shows a unique relaxation process due to the Zener relaxation, with a relaxation time, T , in the vicinity of 100 sec. Curve B, which represents the behavior of the fine-grained sample, on the other hand, shows first the same relaxation process as that in A, followed by a turning up of the curve which corresponds to the onset of a second overlap-

Jan 1, 1962

Discussion of the paper of WALTHER MATHESIUS, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 539 to 555. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-This paper answers. partly the difficult questions which have come up as to why it is not economical to use higher blast temperatures in the smelting of Mesaba ores, such as the high temperatures used in European practices, and the answer is very plain that the ores will not stand the higher temperature. But the paper does not go into detail as to what special difficulties were found with the higher temperature of blast, and I would ask the author to kindly specify them. W. A. FORBES, New York, N. Y.-A large part of the troubles that furnace men experienced in using high-blast heats in smelting Mesaba ores in the early days of using Mesaba ores, was clue to the attempt to use these soft ores on furnaces having the same lines as the furnaces used in smelting the hard Old Range ores. As the result of observation and study, the dimensions of the lower part of the blast furnaces have been changed and the difficulties of the blast-furnace men in operating with a large percentage of Mesaba ore and high-blast temperatures have been largely overcome. The changes I refer to in particular are: (1) steepening the angle of the bosh; (2), decreasing the height of the bosh; (3) increasing the diameter of the hearth. JOSEPH W. RICHARDS.-Mr. Forbes's answer is quite satisfactory, and the moral which it points is that when the furnace is run with a higher temperature in the smelting zone, the furnace lines which were adapted for the lower temperatures are not necessarily those best suited for the higher hearth temperatures. If. enriched blast were used in a furnace, and higher temperatures run, it would be found necessary to further modify the lines of the furnace to meet the new conditions and to get the maximum output with economy. J. E. JOHNSON, JR., New York, N. Y.-It seems to me this is one of the few papers which could well have been a little longer. The data which Mr. Mathesius has given us, I think should be considered in connection with the paper which Mr. Brassert read before the American Iron and Steel Institute last spring, in which he described how they had obtained remarkable results with furnaces with steep but very short boshes; the angles have been raised to 80°, and the boshes made so short that they no longer appear as a conspicuous part of the shape of the furnace.

Jan 5, 1915

(Members are urged to send in for this column any notes of interest concerning, themselves or their fellow-members.) Members and visitors who registered at institute headquarters during October A. Adiassewich, St. Petersburg, Russia. Charles W. Merrill, San Francisco, Cal. A. F. Lucas, Washington, D. C. Carl J. Trauerman, Butte, Mont. Allan J. Clark, Lead, S. D. Herbert B. Cox, Boston, Mass. Prof. Loewinson-Lessing, St. Peters- James W. Malcolmson, Kansas City, Mo. burg, Russia. A. E. Sunderhauf, Paramaribo, Dutch F. Maury Gillespie, Abangarez, Costa Rica. Guiana, S. A. M. Gardner Talcott, Irvington-on-Hudson, N. Y. D. W. Brunton, Denver, Colo. A. P. Watt, Newark, N. J. Dwight E. Woodbridge, Duluth, Minn. S. A. Taylor, Pittsburg, Pa. Alexander Fyfe, Boston, Mass. Ralph Wilcox, Miami, Ariz. Robert A. Seip, Wilkes-Barre, Pa. William J. Cox, Denver, Colo. A. J. Eveland, Boston, Mass. E. P. Ross, Duquesne, Pa. M. F. Sayre, Brewster, N. 1. H. Mortimer-Lamb, Montreal, Canada. Albert Sauveur, Cambridge, Mass. F. L. Grammer, Leesburg, Va. Robert H. Leach, Brockton, Mass. R. R. Moore, Mexico City, Mex. Steinar Foslie, Kristiania, Norway. Charles E. van Barneveld, San William A. Wong, Honolulu, Hawaii. Fran¬cisco, Cal.

Jan 11, 1913

By Y. C. Liu, G. A. Alers

The effect of rolling reduction on the textures of Cu-A1 alloys has been investigated both by pole figure and by modulus methods. In alloys which exhibit complete copper or brass types of rolling texture, the rolling reduction has little effect on the texture except to increase the degree of preferred orientation. In alloys which exhibit a transition texture, however, increased rolling reduction increases the amount of brass-type texture at the expense of the copper-type texture. The present experimental results show that there is no one-to-one correspondence between the SFE and the rolling texture of fcc metals. Additional data taken from the literature for fcc metals also support this conclusion. On the other hand, the present and previous experimental results are shown to be in good agreement with the suggestion that the texture transition occurs at a critical value for the separation distance between two partial dislocations—a consequence of the "dislocation interaction" hypothesis for texture. formation. This critical separation occurs when the parameter .r/ub is 3.75 x 10'3. From this, a value for the SFE of 39 ergs per sq cm may be deduced for a Cu-2.85 at. pct A1 alloy. ThE correlation between the rolling texture of fcc metals and the stacking fault energy, SFE, was one of the first attempts to relate atomistic properties with the type of rolling texture.' This correlation gives a qualitative explanation for the experimental observation that the addition of alloying elements, which generally lower the SFE, changes the copper-type texture to a brass-type texture. The simplicity of this correlation had led to its general acceptance and even its quantitative use.' However, it is only a correlation and is largely based on descriptive features of pole figures, and on the poorly known SFE values in dilute alloys. Quantitative verification of this phenomenologi-cal correlation is, in fact, completely lacking. One purpose of the present study is to test this correlation. Another atomistic description for the formation of rolling texture is the "dislocation interaction" hypothesis of texture formation.3 In this hypothesis, the factor controlling the type of rolling texture depends on whether or not the separation distance between two partial dislocations exceeds a critical value. Materials having a separation of less than the critical value are supposed to exhibit a copper-type texture while those with a separation above the critical value are supposed to have a brass-type texture. At the critical value, it is expected that the material should show equal amounts of copper- arid brass-type orientations in their textures, i.e., a 50 pct transition texture. The SFE appears in this hypothesis as only one of several factors which determine the separation distance between partial dislocations. It is possible to test the validity of these two concepts by studying the rolling texture as a function of rolling reduction. Since the SFE per se is an intrinsic property of the metal, it should not, by definition, be influenced by local irregularities, such as variable stress conditions. Thus, no change in texture-type is expected to occur with changes in rolling reduction. On the other hand, according to the "dislocation interaction" hypothesis, any factor that effectively influences the separation distance of partial dislocations would be expected to change the rolling texture. Since the separation distance between partial dislocations is known to depend upon local stresses,4-6 it is anticipated that there would be an effect of the degree of reduction on the texture-type. Also, since applied stresses are more likely to increase, rather than to decrease, the separation between partials,4'5 the overall effect would be to increase the amount of material in the brass-type orientations as rolling reduction is increased. Furthermore, this reduction dependence would be most prominent in alloys exhibiting the transition texture since the distance between partials in those alloys is thought to be close to the critical value. Experimental data in the literature is insufficient to distinguish between these two alternatives. Haessner studied the effect of rolling reduction on textures in a series of Ni-Co alloys by means of the X-ray intensity-ratio technique,' and found that while one texture parameter indicated no reduction dependence the other indicated a slight dependence of the rolling texture on reduction in the range of 96 to 99 pct. As has been noticed previously, the intensity-ratio technique is a convenient but controversial method7 because there is no a priori reason to suggest which intensity-ratio would describe the texture most meaningfully. A more quantitative method of describing textures is found in terms of the orientation dependence of Young's modulus. Here, the type of modulus aniso-tropy associated with the copper-type texture is sufficiently different from that observed for the brass-type texture to allow the two types to be easily distinguishable and a quantitative measure of the amount of each can be deduced from the numerical results. This ability to provide quantitative data is particularly valuable when the two textures occur simultaneously in one alloy as is the case for the transition textures. In this paper the modulus method, supplemented by pole figure data, is used to look for an effect of roll: ing reduction the texture. Also by combining the texture measurements with recent determinations of the SFE in Cu-A1 alloys'0'" it should be possible to test for a relationship between the SFE and textures.

Jan 1, 1970

J. A. Mathews,* Syracuse, N. Y. (written discussion?).-It is interesting to note how frequently we hear of some process that is going to revolutionize the tool-steel business. I don't know why it is, but every one seems to have it in for us poor tool-steel men. About 15 years ago, a good-sized plant was built in Syracuse for the manufacture of cast tools of malleable iron. The promoter of the scheme claimed to have a secret, process that had been given to him by a tramp to whom he gave a lift along a dusty road. The widows and orphans invested liberally in the securities of the company without consulting the men established in the machine-tool business in Syracuse. About two years later, when the sheriff's sale occurred, the secret, which was carried on the books of the company as an asset valued at $2,000,000, brought $15 at auction. A little later another concern started on the theory of replacing scrap high-speed steel with new high-speed steel tools made therefrom. All the tool-steel companies have made a practice of purchasing high-speed

Jan 5, 1919

BOSTON SECTION ALFRED C. LANE, Chairman, GEORGE A. PACKARD, Vice-chairman, E. E. BUGBEE, Sec'y-Treas., Mass. Inst. of Technology, Cambridge, Mass. R. L. AGASSIZ, FRED W. DENTON. Forty-sixth Meeting The forty-sixth meeting of the Boston section was held at the University Club on Monday evening, Jan. 28, 1918. Thirty-six members and guests were present, which is a record for this Section. After a good dinner, President Philip N. Moore, of the Institute, was introduced, and spoke of the many problems of the Institute. The topics covered were the progress and growth of the Institute during the administrative year, the efforts to stimulate the local sections and to bring them more in touch with the policies and problems of the parent body and, last but not least, of the constructive results and patriotic work of the Institute in the national service of the war. The other guest of the Section, Mr. Thomas Nelson Perkins, Counsel for the Priority Board, spoke most entertainingly of recent experiences in Russia, England and France. After considerable discussion during which Mr. Perkins most obligingly answered innumerable questions, the meeting adjourned at about 10 p. m.

Jan 7, 1918

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 x 10[9] cu yd (1.4 X 10[9] m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 X 10[6] cu yd (19 X 10[6] m3) annually.

Jan 11, 1979

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By R. M. Waterstrat, B. N. Das, Paul A. Beck

The central region of the Ti-Mn system was studied by means of x-ray diffraction and metallography. The following intermediate phases were found: an MgZn2-type Laves phase having a wide range of homogeneity, the p-phase of unknozvn structure, and the + -phase with a large tetragonal unit cell, stable at 930°C and lower temperatuves. MaYKUTH, Ogden, and jaffee1 determined the soh-inh bility limits of manganese in and titanium. They also confirmed the structure of the intermediate phase TiMn2 which was previously identified as a Laves phase of the MgZn2 type.2 In the equiatomic region they found an additional intermediate phase, y, which presumably formed by a peritectic reaction at approximately 1200°C. This last observation was disputed by Rostoker, Elliott, and McPhers0n,3 who reported the formation of TiMn by a peritectoid reaction between 900" and 1000° C, but found no evidence of any intermediate phase other than the Laves phase at higher temperatures. Elliott and Rostoker4 reported furthermore that the X-ray diffraction pattern of TiMn could be identified as that of a o phase, although their data were not consistent with this inter~retation. Margolin and Ence6 presented X-ray diffraction data for the and TiMn, phases, and obtained metallographic indications for the existence of additional intermediate phases. They concluded from metallographic observations that two Laves phases are formed, separated by another phase, designated as &. A phase diagram for the Mn-Ti system has recently been published by Savitskii and Kopetskii,&apos; which shows considerable disagreement with the work of Hellawell and Hume-Rothery,&apos; in particular with regard to the terminal solid solutions based on the allotropes of manganese. The present investigation was undertaken primarily to clarify the phase relationships in the equiatomic region of the Ti-Mn system. The metals used in preparing the alloy specimens Were iodide titanium and electrolytic manganese, the latter having a nominal purity of approximately 99.9 pet. The electrolytic manganese was covered with a thick coating of a brown manganese oxide which was reduced by heating the manganese flakes for several hours at a temperature of 1100°C in an atmosphere of dry hydrogen. Three alloys, see Table I, were made using sponge titanium and manganese not treated in hydrogen. The alloys were prepared by arc-melting in an atmosphere of helium or argon. The composition of each alloy was calculated by assuming that the entire weight loss during melting was due to evaporation of manganese. Subsequent chemical analysis of certain alloys indicated that the compositions calculated in this manner were usually correct within 1.4 pct, as shown in Table I. All alloy specimens were wrapped in molybdenum foil before sealing them in silica tubes containing argon at a pressure of 1 atm at the annealing temperature. After quenching in cold water, the alloy specimens were bright and clean, with no evidence of any surface reaction. The alloys listed in Table I were examined metallographically, using an etchant consisting of 20 pet HNO3, 20 pet HF, and 60 pet Glycerine. powder for X-ray diffraction examination was prepared by crushing a portion of each annealed alloy

Jan 1, 1962

amounted to about 2000 metric tons. The total output is increasing from year to year. Marine salt is now produced in Haiti in quantity sufficient to supply nearly all the requirements of this Republic, so production tax is now collected. Central America Guatemala-The major production of salt in Guatemala is solar salt derived from sea water, but the Indian population prefers salt derived by boiling coastal marine earth. Salt is taxed by the Government. The industry has been beset by controversies in recent years, especially following the revolution of October 1944. The Government issued a decree in August 1940 designed to control production and price of salt. The creation of a salt consortium was provided for and marketing was to be governed by production quotas. It is understood that the Government pool was later dissolved and the industry is now under older laws whereby production and sales have no limits. South America Panama-Output of salt in Panama in a very recent year was 11,000 net tons of solar-evaporated sea salt. A Government bank is in charge of output and distribution of the product. Colombia-Rock-salt deposits are known in five places-Zipaquira, Nemocon, and Sesquile, in the Department of Cundinamarca, the Cumural y Upin near Restrepo, and San Miguel y Barital, near Medina in Meta Intendency. The latter deposit never has been worked on account of its inaccessibility. Saline springs are worked in four locations. The largest producer among marine salinas is Manare but it is now planned to make Bahia Honda the largest. Some evaporated salt is made in vacuum pans. The deposits at Zipaquira, Nemocon, and Sesquile are believed to occur in the domal type of deposit. All the salt resources are under Government control. Venezuela-The salt industry in Venezuela is under Government control and is taxed. Taxes in recent years, however, have been reduced for salt used in curing hides and salting meats, fish and fish products. Production has approximated 25,000 metric tons yearly but may now be considerably above that figure. The basin on the peninsula of Araya, State of Sucre, which at present is the only important source of salt, could produce at least 175,000 metric tons if more ground were provided-a larger supply than the entire country could consume. This unique landlocked basin of nearly 1000 acres lies 12 ft below sea level. Ecuador-Salt is a Government monopoly in Ecuador and is produced chiefly by solar evaporation close to the shore. The main producing center is on the Santa Elena peninsula, which supplies about 90 pct of the salt. Small fields are at Punta Arenas, Payana, and Chara-

Jan 1, 1949

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,&apos; it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By Arthur Knapp

OIL-WELL depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. DATA FOR LEASE STATUS-TIME OR DOLLARS-TIME CURVE TIME LEASE MONTHS STATUS Lease purchased for $3000 0 -$ 3,000 No expenses chargeable to lease for 3 mo 2 - 3,000 Well A is started; cost of drilling for month is $16,000 3 - 19,000 Well is completed at additional cost of $10,000 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (see Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.: difference between expenditures and receipts gives profit for month of $5,000 5 - 24,000 Investment is small, cost of operating well A is small, so profits are $15,000 6 - 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000.... 7 - 5,000 Lease operation now becomes normal and curve becomes smooth 8 - 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000

Jan 1, 1921

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe&apos;s laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe&apos;s death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.&apos; Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

THERE are three chief production zones of tungsten ore in China. In the Province of Kiangsi mines are located at Kanchow, East River, and West River. Their combined production is understood to amount to 300 to 350 tons of ore per month, and their original exportation is made through the port of Kiukiang, largely to Shanghai. The second zone is in Kwangtung Province, the mines there being at Tayulin. Produc-tion reaches about 200 tons per month and cargo is gen-erally exported through the port of Hong Kong. In the Province of Hunan approximately 25 tons of ore are produced monthly in the mines at Ton-on. Tungsten ore from Kiangsi and Kwangtung Prov-inces is generally about 70 per cent WO, (tungstic acid), while that from Hunan is of lower quality, run-ning about 65 per cent WO3. Kiangsi ore is received from the mines in 100-1b. and Hunan in 224-lb. gunny sacks. No repacking is done except as it is made neces-sary by the condition of the sacks. Kiangsi Province contains the Chinese districts pro-ducing the largest amount of salable wolframite or tungsten. Many districts west and south of Kiangsi have been found to have wolframite deposits.-Com-merce Reports.

Jan 1, 1928