Search Documents

By A. W. Hale

IN a work published in 1838, De Morgan, the author of the article on "Probabilities,' in the Encyclopedia Metropolitana, says " The method of least squares is not yet introduced into the affairs of common life,….that many things which are demonstrable only by the higher branches of mathematics are looked upon as useless." And he mentions an instance in which "a method was suggested for estimating the relative importance of boroughs, by considering their population and contributions to the revenue com-

Jan 1, 1881

By J. F. Wilkinson

A high degree of accuracy is often required in mine-surveying, in order that expensive mining work may not be misdirected. The making of underground connections by drifts or shafts located as the result of surveys presents a crucial test of correctness not usually involved in any other class of surveying. In view of these considerations, the present notes and description of a survey made in June, 1890, for the San Francisco shaft of the New Almaden quicksilver-mines, may be of interest to members of the Institute who are surveyors. The purpose of this survey was to locate on the surface a vertical 2-compartment shaft (3.5 by 7 ft.), to connect with another vertical shaft, of practically the same size, which had been sunk a number of years before from an adit-level about 240 ft. vertically below the surface, to a deeper, so-called 600-ft. level. It will be seen, of course, that the most important matter was to secure an exact coincidence in vertical line, so that the resulting continuous vertical shaft from the surface should have no offset or irregularity at the point of junction between its two parts. The levels were of less importance; but, as the hoisting-works were to be placed in position and the new shaft permanently timbered from the start, its correct alignment was an essential requirement. The important features of the work, therefore, were the methods used in determining with certainty : 1. That the shaft was located in the right place in a general way; 2. That the ordinary inaccuracies of linear and angular measurements were so reduced as to insure correctness of location within certain defined and allowable limits. Instruments.—Thc instruments used were: a Buff and Berger transit-theodolite, with a 6-in. horizontal plate, reading to 10 seconds; a Heller and Brightly Y-level; a Chestermán steel tape, graduated in tenths and hundredths of a foot; and New York leveling-rods, graduated to thousandths of a foot.

Jan 1, 1901

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By Y. Mishima, R. Shiromizu

THE equilibrium y phase in Cu-Be alloys forms by discontinuous precipitation, the new phase nucleating at the grain boundaries and growing into grains on both sides of the boundary. When the alloy is aged above 500°C, however, growth may take place into only one of the grains.1'2 In A1-Ag alloys it is known that the precipitate has the same orientation as the grain in which no growth takes place.3, 4 This was confirmed in the present investigation on a Cu-Be alloy. A Cu-1.79 wt pct Be alloy was solution-treated at 810°C for 2+ hr, quenched into water at O°C, and aged at 600°C for 1 hr in a salt bath. The specimen was thinned by chemical polishing and electropolishing at room temperature in a solution of H3PO4 saturated with CrOs. The foil produced was examined in a JEM 150 electron microscope operating at 150 kv. Fig. 1 shows precipitates growing on only one side of the grain boundary. The black platelike precipitates were identified as the y phase. Electron dif-

Jan 1, 1969

By Lawrence Addicks

SOME three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed y constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge. was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust Were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and Was fired with fuel oil. A run of several hours yielded excellent nodules. The kiln showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal. of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per. ton of flue dust shown on the test and as fuel oil at that time Was selling around 2 1/2 c. per gallon it was decided to let it go at that.

Jan 7, 1914

By M. S. Burton, B. W. Christ, G. V. Smith

Evidence of the effects which high-angle grain boundaries and veining subgrain boundaries have on the yield phenomenon of zone-refined iron is reported. Room-temperature tensile tests on 50-mil wive at several gram sizes produced upon recrystallization at diffevent temperatures below 910C (a-y phase-transfornzatzon temperature) show that upper and lower yield stress decrease with increasing grain size. The upper yield point effectively disappears at grain sizes of 81 and 102 u in samples of this diameter. However, samples of 129 p grain size. produced during recrys-tallization at 950°C, exhibit a pronounced upper yield point and an increased lower yield stress. Possible causes of the reversal in the grain-size dependence of yielding are discussed. Veining substructure, detected with picval-HC1 etchant, but not with 2 pct nital, is formed during the a-y transformation, and is believed to account for the observed effecls. The strengthening associated with high-angle boundaries in zone-refined tron is discussed in terms of: 1) the stress dependence of slzp multiplicity, and 2) the stress dependence of dislocation emission from grain boundaries. WIDE use of transmission electron microscopy and dislocation etch-pitting techniques has led to a growing awareness of the presence of dislocation substructures in annealed pure metals. Whereas much speculation'-4 has developed about the influence which subgrain structures have on the mechanical behavior of metals, particularly the yield strength, only limited experimental evidence correlating subgrain structures with lower yield strength has been presented. 2,3,5-7 It is the purpose of this note to present experimental evidence of the effects which grain boundaries and subgrain boundaries have on both the upper and lower yield strength of zone-refined iron. Effects due to high-angle boundaries formed upon recrystallization below the a-y phase transformation are compared with effects due to veining subgrain boundaries formed upon "recrystallization" above the a-y phase-transformation temperature. These effects are further compared with the reported influence 2,3,5-7 which low-angle boundaries have on the lower yield strength of bcc transition metals. EXPERIMENTAL PROCEDURE The starting material for these experiments was a 1-in.-diam zone-refined ingot prepared at Battelle Memorial Institute. Initial purification of electrolytic iron by vacuum-induction melting was improved by a floating zone-melting treatment in ultrapure hydrogen.' Chemical analysis of this zone-refined iron appears in Table I. Tensile samples of 50-mil wire were prepared by rolling and drawing portions of the ingot. An intermediate recrystallization anneal at 625°C after rolling to a reduction in area of 85 pct was carried out in an evacuated Vycor capsule (10-=5 mm Hg). Further reduction in area of 91 pct was followed by recrystallization in evacuated Vycor capsules at temperatures between 600" and 950°C, see Table 111. All samples

Jan 1, 1967

The Mines Handbook, Published by Mines Information Bureau, Inc., Suffern, N Y. It is felt that the Mines Information Bureau should be included in this directory, as publishers of a valuable reference book of mining companies of the United States and Canada, known as the "Mmes Handbook "

Jan 1, 1933

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson') in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda's work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470'C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927

By C. Y. Cheng

THE purpose of this note is to show that the dislocation mechanism controlling the creep of Fe-4 pet Si alloy1 may equally account for the behavior of a-Fe2 over the same temperature range. A recent study of the creep behavior of a-Fe has been made by Ishida et al.2 Their results were in agreement with the mechanism of nonconservative motion of jogged screw dislocations over the entire range of temperatures investigated, from 480° to 1045°K. However, the observed creep rate was much higher than that which could be accounted for by the above model unless the authors assumed that pipe diffusion became significant below 775°K. More recently, Cheng et al.1 inves-gated the creep of Fe-4 pet Si alloy over about the same temperature range and found that the results could be correlated fairly well with a dislocation climb mechanism as represented by Eq. [l]. Proceeding as shown previously,1 if creep is controlled by a single climb mechanism, at intermediate stresses, the shear creep rate, y, can be represented by where n and K are material constants {K is independent of the temperature but dependent on the structure, that is, K decreases during the primary stage and reaches a steady-state value over the secondary stage of creep), t is the applied shear stress, G is the shear modulus, gc is the free energy of activation for creep (usually equal to that for self-diffusion, gd), and RT has the usual meaning. By solving for y, the apparent activation energy for creep, Q which can be determined experimentally, is given by where hc is the enthalpy of activation for creep which usually is also equal to that for self-diffusion, h^. By using Eq. [2], the data in Fig. 2 of Ref. 2 can be re-plotted as shown in Fig. 1. By comparing the two figures, it is seen that the slight increase in the apparent activation for creep over Region II, as noted in Fig. 2 of Ref. 2, is due to the influence of temperature on the shear modulus rather than of the stress on the

Jan 1, 1969

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the' second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson' argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By Harry Klemic

Zirconium and hafnium minerals are used industrially both as minerals valuable for their chemical and physical characteristics and as ores of zirconium and hafnium. The principal zirconium-hafnium-bearing minerals, their composition, and their ranges in content of zirconium and hafnium dioxides are listed in Table 1. The supply of zirconium and hafnium is based almost entirely upon the supply of the minerals zircon and baddeleyite. Eudialyte may eventually also be of importance as a source of these elements. Zircon, which generally contains nearly 49% zirconium and between 0.4 and 1.5% hafnium, is the principal industrial mineral of this group. Baddeleyite, a commercially important but less abundant mineral, contains as much as 73% zirconium and 0.4 to 1.7% hafnium. Eudialyte has a wide range in content of these elements, but analyses of material from several localities indicate values of 6 to 11 % zirconium and 0.07 to 0.4% hafnium. Zircon is a mineral consisting principally of zirconium, silicon, and oxygen that crystallizes from magmas during the formation of igneous rocks. Zircon also occurs in veins and in metamorphic rocks. It is in the tetragonal crystal system. It commonly forms as small well-developed prisms having pyramidal terminations but also occurs as irregular-shaped grains. Zircon has a hardness of 7.5 on the Mohs' scale. Its specific gravity is commonly between 4.68 and 4.70 (Dana, 1932), but the specific gravity varies somewhat depending upon com- position and state of alteration. Zircon has no good cleavage directions and is brittle, breaking with a conchoidal fracture. Zircon of the composition ZrSiO, would contain 67.2% Zr02 and 32.8% SiO2. However, in addition to about 1 % of hafnium, minor amounts of thorium, uranium, rare earth elements, yttrium, calcium, magnesium, iron, aluminum, phosphorus, and hydrogen, and trace amounts of other elements are commonly present in the mineral (Frondel, 1957). Radiogenic lead and other daughter products from the radioactive decay of uranium and thorium also accrue in the mineral. Radiation damage to the structure of zircons that contain appreciable amounts of uranium and thorium may alter the internal structure of the crystals to

Jan 1, 1975

By William Y. Warren

Messrs. Thomas & Cross, having leased from the Akron Cement Company from twelve to fifteen acres of abandoned cement-tunnels and chambers, for the purpose of propagating mushrooms for the market, commenced operations about a year ago, and are now beginning to furnish mushrooms in quantities to the local markets of Buffalo and Rochester. The quarries, or, more properly, the mines, of the Cement Company are located at Akron, Erie County, PIT. Y. The cement-rock occurs in a stratum about 71/2 to 8 feet in thickness, which is overlain by from 1.5 to 25 feet of limestone and flint-rock. There is a gentle rise from the opening of the tunnel inwards, giving a natural drainage and leaving the chambers comparatively dry. The roof is good and is supported by pillars and heavy timbers. The mushroom-beds are located about 300 feet from the opening of the tunnel, and are made in the form of mounds about 3 feet by 12 feet, at the base, and 24 feet high, giving to the chambers the appearance of a subterranean graveyard. Many experiments have been made to determine the best form for the beds, and the mound

Jan 1, 1889

By H. Y. Hunsicker

A graphic method has been devised for three-di-mensional analysis of hot deformation and for correlating the amount and directionality of the deformation with resulting directional properties. Deformation is evaluated in terms of dimensional change ratios referred to three orthogonal axes. Since all combinations of the three ratios can be represented in a triangular coordinate field with logarithmic scales, a two-dimensional chart of extent of deformation and degree of asymetry is possible. The entire gamut of shape changes from upsetting through flat-rolling to rod-rolling is accommodated. The resulting coordinate system is a base upon which can be represented the properties of the wrought products measured in the directions of the axes employed fir evaluating the deformation. When property data are available for many types and amounts of deformation, a three-dimensional figure can be constructed, and the projection of this figure is referred to as a ''3d'' chart. Experience in using such charts to plan fabricating operations for a variety of thick-section forged and rolled products of heat-treated aluminum alloys has verified its practical value for optimizing directionality relationships. MechANICAL anisotropy of thick section products of heat-treatable aluminum alloys is recognized by producers and users of these products, and the extent of the directional differences is apparent in property tabulations included in handbooks, standards, and specifications.' Attention has also been directed to the existence of important directional differences in the resistance of these products to stress-corrosion cracking. Metallurgical structure factors responsible for these directional differences include, among other possibilities, shape and alignment of grains, voids and nonmetallic inclusions (when present), volume fraction and spatial distribution of secondary phase particles and solid-state precipitates, crystal-lographic textures, and Bauschinger effect. The contributions of the individual factors vary with alloy composition, heat-treated temper, type of working process (forging, rolling, extrusion), and the amount and directional nature of the deformation. In general, the cast ingot used as the starting material for producing these wrought products exhibits only a modest degree of directionality. A monotonic and continuous transition from this nearly isotropic state with progressive hot deformation would appear probable, assuming that the working temperature is sufficiently high to cause continuous dynamic recovery. Several years ago a project was undertaken to evaluate the effects of hot deformation and metallurgical structures on the directionality of thick wrought aluminum alloy products, and the method to be described was developed as an analytical tool in this investigation. DIRECTION NOMENCLATURE The nomenclature system adopted by industry for the three mutually perpendicular directions employed in testing aluminum alloy products includes four terms: "longitudinal", "transverse", "long transverse", and "short transverse". These terms are conventionally related to the external geometry of the product but also by implication to the deformation and resulting metallurgical structure. Occasions arise in which through use of unusual fabricating methods, intentional or otherwise, the structure does not have the usual relationship to external geometry or may be very complex because of inhomogeneity of deformation throughout the piece. The longitudinal direction is generally parallel to the primary rolling direction or to the direction of extrusion. In the case of forging, it is parallel to the direction of maximum extension (not maximum "working" or "flow", as frequently stated). The term transverse is applied to any direction perpendicular to the longitudinal direction in a product having symmetry about the longitudinal axis, and generally, although not always, the deformation to produce these forms is nearly symmetrical in the transverse plane. This term then may be applied to a round, square, hexagon, or other polygonal, symmetrical shape produced by extrusion or rolling or by forging, if produced by a simple, symmetrical drawing procedure. The type of microstructure generally associated

Jan 1, 1970

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By W. P. Lass

(San Francisco Meeting, October, 1911.) TEE purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Gold Mining Co., at Douglas Island, Alaska., under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows: Smelting-charges, . $4.00 Loading, freight, insurance, etc., 2.89 Interest due to time lost in transit and in settlement, . 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 5.01 Total, . . $11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows; Per Day. Per Ton. Labor, . $66.16 $0.827 Chemicals, . 76.60 0.960 Power and steam-heat, 67.60 0.845 Marketing-, refining- and other charges, 49.36 0.617 Totals, . . $259.72 $3.250 Adding to this total the 4 per cent treatment-loss, which on 3-oz. concentrates amounts to $2.48, gives a total cost of $5.73 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Feb 1, 1912

By H. Y. Bassett

THIS paper attempts to show the various major operations used in nonferrous tube mills and does not necessarily represent the current practices at the two plants of the Wolverine Tube Div., of Calumet and Hecla Consolidated Copper Co. Inc. The operations now utilized in the production of tubing are quite varied and show the continual interest and advance metallurgically and mechanically to produce the best quality at the lowest cost. Naturally, any advance or lowering of cost is dependent on large production runs, which mean longer machine running time with maximum worker productivity. Standardization of tube sizes and elimination of unnecessary alloys are therefore very necessary, otherwise the development of costly new production machines would be of little benefit to the consumer as a whole. It should be noted that in such a short presentation it is impossible to describe in any detail the major operations. The short descriptions, it is hoped, will enable all who are interested to obtain a general idea of present, day practices in the copper tube producing field. Fig. I is a flowchart or sequence of operations showing the steps usually employed in tube production. RAW MATERIALS Quality starts with the raw material, and it is absolutely necessary that raw material be controlled and held to rigid specifications. Little need be said, however, regarding the raw materials for the casting of bars or billets, as the material always is purchased and checked against the various governing A.S.T.M. specifications. CASTING Casting, as is indicated in Fig. I, is quite varied and for convenience can be classified into two groups: The casting of solid billets, and the casting of hollow tubes, each of which is the base for subsequent operations. In the melting of the raw materials various types of furnaces are used, and the selection of any one is dependent on many factors outside the scope of this paper. However, as of general interest, a short description will be made of each. Induction Furnace (Low Frequency) This is popular in the melting of copper-base alloys, Fig. 2. In the induction furnace the principle of an inefficient transformer is used for the production of the necessary melting heat. The primary coil is.arranged around a transformer core made of high permeability silicon steel sheet. The secondary circuit is through a melting channel around the primary coil and opens into a hearth which contains the main charge. The heat is generated only in the melting channel, but because of the stirring action there is a constant flow of metal around the channel, which when mixing with the charge causes very rapid melting. The volatilization losses are very low as the furnace atmosphere above the charge is heated only by the heat from the melting metal. The stirring action, however, makes the use of any slag cover difficult. Such furnaces- must be started with molten

Jan 1, 1951