Search Documents

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,' little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district. The recognition of alteration phenomena and related features by Hoyt S. Gale3 in 1935, followed by the work of Shenon and McConnel in 1936-37,4 changed many of the concepts formerly held and opened the way for more critical study and mapping of alteration effects. Mapping of these effects has been in progress for several years but no well-organized, careful, and complete laboratory study of the alteration has been made by mining companies or by government agencies. Recently, Thomas Mitcham of Columbia University has been occupied in the collection and study of specimens carefully selected from several producing mines in the Silver Belt as well as from several prospects exhibiting alteration effects. Mr. Mitcham and the writer have discussed some of the preliminary results of his investigations, which indicate that definite and interesting material is forthcoming from his studies. Work of this kind, aided by careful observation by district geologists, should advance the knowledge of the environment of Silver Belt ore shoots and establish additional criteria for recognizing meager shallow expressions of deep-lying orebodies. Structural details in the Silver Belt area are extremely difficult to decipher on the surface because the area is almost completely covered by a deep mantle of surface debris and soil. A dense growth of small trees and buck brush adds to a geologist's difficulties. Often large areas reveal only scattered small outcrops with great intervening areas where the underlying formations must be deduced from small altered rock fragments. Some considerable success in obtaining surface information has come from bulldozer roads and cuts in selected areas. As this type of work receives more attention, knowledge of the surface expressions of formations, alterations, faulting, and veining is expanding and giving more reliable information to guide deeper development. Lack of diagnostic marker beds in the district contributes to a geologist's difficulties in determining fault displacements. In the Silver Belt, known commercally important sulphide orebodies commonly are associated with siderite and quartz gangue. Some of the veins at shallow horizons above productive ore shoots are composed of quartz with light-colored carbonate minerals such as calcite, ferrocalcite, ferrodolomite, ankerite, and carbonates with variable amounts of manganese. The relation of these carbonates to commercial orebodies is a problem offering possibilities for research. Shallow exposures of veins composed of quartz and the light-colored carbonates, often with some associated barite, grade into quartz and siderite veins at deeper horizons. The vertical range of these carbonates has been partially established for some veins, but no reliable method has been devised for predicting where the change in a vein may take place. Careful observation and analysis of carbonates may make it possible to predict more closely where the change to siderite may be expected. In 1926 Shannon5 pointed out some of the characteristics of the carbonate veins of the district and included a few chemical analyses. Some of the Silver Belt ore shoots have small commercial outcrops, and very shallow development of some properties has led to the opening of small ore shoots." Several small ore shoots developed at shallow depths have not been explored at deep horizons, and some important ore shoots with no commercially significant exposures at shallow horizons have been developed. The greatest problem of the mining geologist working in the Silver Belt area is to find the all-important link between the very meager shallow expressions of mineralization and the rich ore shoots that may be found below. To develop criteria for use in the recognition of the weak upper expression of ore shoots, the experience of past development programs must be relied upon heavily. The investment of more than a million dollars in the exploration for such ore shoots requires some reliable criteria if these ore shoots are to be found. Management needs some assurance that the risk involved is justified by well-developed and acceptable geological inference. The richness of some of the ore shoots found thus far has contributed greatly to the justification for a bold approach, but many negative results of blind exploration programs would lead eventually to extreme caution on the part of management. Fortunately, recent experiences of development programs have been quite successful. It is hoped that added knowledge. of the environment of Silver Belt ore shoots will contribute greatly to the sureness of approach toward their development. The Coeur d'Alene mining district is located in the panhandle of Idaho in Shoshone County. The population of the county is either employed in the

Jan 1, 1952

By M. von Heimendahl, G. Thomas

The microstructure of TD-Ni has been examined by transmission electron microscopy in the extruded, annealed. and deformed states. The tensile properties hove been correlated with the observed microstructures and the results ore com-pared with those obtained from pure nickel. The important conclusions are that the thorin particles in TD-Ni act as strong burriers to dislocntion motion during both deformation (slip) and annealing (climb). During deformation. the dislocations tangle around the particles and a cell structure is devleloped after 10 pct or more strain. The cell size appears to be determined by the spacing of the largest particles and is about five times smaller than that in pure nickel for the same strain. The higher work-hardening rate in TD-Ni compared to nickel is probably due to the more rapid rate of dislocation multiplication in the alloy as a result of dislocation-particle interactions. The Th0,particles inhibit recrystallization and twin growh so that some strengthening may arise from the high density of small annealing twins. THE strengthening of materials due to the presence of a dispersed second phase has been the subject of considerable experimental and theoretical investigation in recent years. One of the newest dispersion-strengthened alloys to be developed is TD-Ni,1 a system of approximately 2 vol pct thoria (ThO2) dispersed in a matrix of commercially pure nickel. This material is fabricated by powder-metallurgical techniques and offers high-temperature stability and useful mechanical properties virtually to the melting point of the base metal. While the mechanical properties of this system have been investigated,2,3 there have been no reports in the literature concerning the microstruc-ture of TD-Ni and its correlation to mechanical properties. This paper describes a transmission electron microscopy investigation of the micro-structure of TD-Ni together with its mechanical properties. The results are compared with the structure and properties of pure nickel.

Jan 1, 1964

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.'" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By S. M. Marshall, B. M. Bird

For a number of years European investigators have used laboratory methods of predicting the probable strength of coke made from coal, and recently several investigators in the United States have reported the use of various tests for this purpose. There is at present no method accepted as standard, however, nor is there even agreement as to the general type of test that should be used. Furthermore, because the details of most of the tests have not been worked out carefully, one investigator can not hope to duplicate the work of another. The extension of coke manufacture to new localities in the United States, and the increasing need for cokes of exceptional qualities made from the most economical mixtures, made it desirable to have some simple laboratory test which will determine whether given coals, alone or blended with other coals, are more satisfactory from the standpoint of coke strenpth- than others of different cost. The work described herein has resulted in the development of a simple laboratory test which, it is believed, can be generally adopted in coal laborat,ories, and which will give concordant results even though performed by different investigators in different laboratories. The general method of predicting whether a coal or a mixture of coals will produce a strong coke, resistant to crushing and shattering, has been to correlate the known strengths of the cokes produced in commercial ovens with some measurable constituent or with some property of the coals, and then to use the relationship so found for forming an estimate of the coking strengths of coals unknown. Several such correlations have utilized the percentages of the various ultimate constituents of coal, such as the oxygen content and the hydrogen-oxygen ratio;(39)§ other correlations have involved the proportion of a, B and r com-pounds, (17,21,30c) or of "oil and solid bitumens."(16,30) Also a relationship has been traced between the coking properties of coal and the rate of change of the resistance offered to the flow of an inert gas by fine particles of the coal while being slowly heated. (11,176) But the most general corre-

Jan 1, 1930

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By Robert P. Koenig

FOR the first time other than on occasion of war the people of the United States are experiencing full-scale participation in world affairs. Public concern has seldom been so involved with conditions and events beyond our own continental limits. Our interest is not wholly of recent origin. Over the years the activity of the United States as a world power and an important trading nation brought about the widening of our political interests and the progressive interrelation of our economy with that of the rest of the world. Some may see in our present phase of world-wide activity the natural consequence of our continued growth. Such observers must also be aware that within recent years our importance in world affairs has been considerably increased. For within the space of an extremely short period events have occurred that have literally jet-propelled the United States into the role of a leading participant in the conduct of world affairs. Little of the choice of this role was left to us. The decline of power in western Europe, the ascendancy between the Elbe and the Pacific shore of an obviously antagonistic force, our earnest endeavor to secure international control of atomic energy, the necessity of providing relief and rehabilitation to war-ravaged areas, and the police work that must be done in occupied territories are problems which have risen in great measure without our help-but they cannot be solved without it.

Jan 1, 1948

By M. D. Curran

AS applied to coal, the term processing is subject to many interpretations. To some it means preparation of coal for the market by mechanical means such as crushing, sizing, washing, or treating with oil or chemicals to eliminate dust or improve combustion quality. To others it means conversion of the coal to other commodities as in carbonization to produce coke and by- products, or to liquids by application of the hydrogenation process. I prefer to classify the various forms of mechanical treatment under the heading of beneficiation and apply the term processing to those methods of treatment that destroy the coal sub- stance through distillation or hydrogenation.

Jan 1, 1939

By Milton H. Fies

THE writer wishes to acknowledge at the outset his great sense of obligation to those who contributed so broadly and expertly to the preparation of this paper: Dr. Albert DeSmaele, Chairman of the Board of Directors of Socogaz, Belgium; Dr. Julien Venter, Director of the National Institute of Coal Mining and Coal Utilization Industry, Belgium; Dr. Roger Loison, Chief Engineer, French National Coal Research Board, France; and Dr. Erich Sarapuu of the Sinclair Coal Co., Kansas City, Missouri. Liberal use has been made in this paper of a recent publication on Russian, Italian, Belgian, and French experiments prepared jointly by the Centre d'Etudes et Recherches des Charbonnages de France (Cerchar) and the Institut National de l'Industrie Charbonnière of Belgium (Inichar).1 The writer is particularly indebted to Dr. E. T. Wilkins, of the Fuel Re¬search Station, London, and to Mr. James L. Elder, of the Alabama Under¬ground Gasification Experiment at Gorgas, Alabama, for their unfailing patience and effective support. Not only did these experienced and capable men edit and revise this discussion, but much of its content is a direct con¬tribution quoted in full from their memoranda. Without the assistance of all these colleagues, this presentation would not have been possible. It has been a privilege to serve and work with them and to acknowledge repeatedly their loyal cooperation. The recovery of the energy inherent in coal beds throughout the world has been done through the years by methods that today may be justly regarded as primitive. While the techniques of coal mining through the application of machines and the enhancement of information and skills have advanced to an extraordinary extent, particularly during the past 20 years, the underlying means is essentially the same as when man first began to mine coal. Despite this progress in the manner of coal mining, it continues today as a hazardous, toilsome, grimy task. Coal mining per se has advanced at a greater and more rapid stride in the past 25 years than the mining of any: other mineral, but the basic method is fundamentally the same as it was the first day a miner took a pick into his hands many centuries ago. This situation presents a challenge to mining engineers everywhere, from

Jan 1, 1953

By C. R. Kuzell

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: C. C. Long, President; John Chipman, Past-President; J. S. Smart, Jr., Vice-President, T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMiTTEE OF THE METALLURGICAL SOCIETY: D. J. Carney, Chairman; Robert Maddin, Past-Chairman; J. H. Hollomon, J. H. Jackson, H. H. Kellogg, T. B. King, F. C. Langen-berg, D. L. McBride, W. O. Philbrook, J. S. Smart, Jr., R. L. Smith, J. D. Sullivan, and F. L. Vogel Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: H. H. Kellogg, Chairman; T. 8. King, Post-Chairmon; R. P. Hermsdorf, W. A. Krivsky, R. E. Lund, C. L. McCobe, Poul Queneou, A. 5. Russell, M. E. Wadsworth, and W. D. Wilkinson. Institute of Metals Division: R. L. Smith, Choirman; P. A. Beck, I. I. Bessen, J. O. Betterton, Jr., R. S. Davis, J. J. Gilmon, R. 8. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurlond, J. J. Heger, M. Hermon, J. N. Hobstetter, H. H. Johnson, Jr., I. R. Krarner, W. C. Leslie, R. A. Meussner, R. R. Nosh, G. E. Pellissier, T. N. Rhodin, A. U. Seybolt, L. L. Seigle, I. S. Servi, P. G. Shewmon, L. Slifkin, J. K. Stanley, C. D. Starr, and J. Washburn. Iron and Steel Division: F. C. Longenberg, Chairmon; H. L. Bishop, C. W. Sherman, J. 8. Wagstaff, and E. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for nan-AIME members in United States and North, South, and Central America; $25, foreign; $5 far AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1960 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ...Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts ... Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 218, Number 4

Jan 1, 1961

By L. C. Morganroth

Magnesites are of two general classes - massive and crystalline.

Jan 1, 1915

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.' Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Arron Finger, Laurence Delisle

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By J. Brian Eby

As is generally understood, the word geophysics means literally ?the physics of the Earth? and the science of geophysics is therefore that which treats of the study and measurements of the various physical properties of the Earth. The broad and general study of the elastic, the gravimetric. or the magnetic properties of the Earth as a whole belongs to the general science of geophysics. The detailed application of this science to rocks of shallow depth and in small areas for the purposes of ascertaining data on their character and structural attitude gave rise to the present well-known science of ?applied geophysics.? Since the discovery of enormous new quantities of oil, gas, and sulphur has been by far and wide the principal benefaction of geo-physics in the United States, this paper will refer only to geophysical methods employed in the search for these particular minerals. The application of methods and appliances originally used for geophysical research to the solution of the practical problems of finding new oil-fields, plus the counterflow or new and highly refined techniques and Instruments from the company and consulting geophysical research laboratories and into non-economic geophysical research, has provided another case of that gen-eral cycle of events which is familiar to all scientists. That this closed-circuit flow or scientific current has been tremendously important to the whole science of geophysics is probably well known to all members of this audience, but the gen-eral status of the exploratory geophysical arts as now used In the search for new oil-fields, the scales on which different methods are being used, the magnitude of the costs involved, and the far greater magnitude of the practical results achieved may not necessarily have come so directly to your attention. It is, I understand, for this reason that this paper has been sug-gested, and I shall seek to provide the information requested by using as case-illustrations those changes in the oil-reserve picture for the United States as a whole, and for the Gulf Coast, California, and Illinois Basin regions in particular, which have occurred in the period of the past 17 years, during which time oil-field discoveries have proceeded at a rate which served to build up known and readily-available (or proven) oil supplies to a reasonable figure, and have dispelled the fears of a serious oil shortage during any period for which valid fore-casts can be made. Not that geophysical-prospecting methods have alone been responsible for this transformation, but they have an indispensable and leading part in the picture of exploration and production-to which geophysics, geology, engineering, and general technical progress have jointly made contribution. So far as the United States as a whole is concerned, its total proven, probable, and possible oil reserves (discoverable and recoverable by then-known methods) were estimated at about nine billion barrels in 1920, whereas proven reserves alone are now com-puted at about 16 billion. In 1920 the driller in ?wild-cat? territory was faced with the knowledge that for every new oil-field opened by a successful well, from 20 to 100 unsuccessful wells would have to be drilled and, in some territories, that the chances for a discovery were really less than one in 100 for new drilling, in contrast to which may be cited the record for the past year in parts of Louisiana where the 67 wells drilled opened 16 new oil-fields, that is to say, where the score of hits to misses was increased to approximately one out of four.

Jan 1, 1940