Search Documents

By Milton E. Wadsworth, T. D. Chatwin

Bulk density variations can usually be minimized by properly mixing the material before moisture measurement. The measuring of moisture on material being with- drawn directly from storage bins requires some form of bulk density correction. In Bethlehem's pellet plants continuous automatic bulk density correction and uniform feed-rate control are obtained with Bethlehem's patented Bin Level Control System. With this sys- tem a single probe, suspended or inserted in the bin, senses whether material is at the proper level in the bin and automatically regulates filter speed to control the filter-cake discharge rate to maintain this level. The level of concentrate in the filter-cake bin can thereby be controlled to within ± 1/2 in. of the point of contact between the concentrate and the probe. Material thickness on the conveyor does not have to be controlled accurately and mix compositions can vary widely as long as they do not contain variable amounts of water-soluble electrolytes. In sinter plants, errors caused by changes in normal feed rate and bed height are minimized by counter-weights that permit the free-floating to maintain a uniform contact pressure on the mix. Large changes in mix resistance can be taken care of either by resetting the control point or by adjusting the calibration control.

Jan 9, 1968

By Kenneth Seaver

Discussion of the paper of KENNETH SEAVER presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1913 .to 1927. J. W. RICHARDS, South Bethlehem, Pa.-This paper concerns a very large industry, and an important detail in that industry. Within sight of where I live in Bethlehem, Pa., are coke works in which $2,500,000 was lost by the use of improper bricks in the coke ovens. This was the fundamental reason of the failure of the plant. The old ovens have all been torn out and replaced by new ovens built of proper bricks. This may emphasize the commercial importance of this subject. When speaking about coke-oven brick, the first thing that comes to my mind is how important it would he if it were possible to. get a brick of better heat conductivity. The heat for coking coal has to go through the thickness of the brick. The silica brick used has low heat conductivity as compared with some other refractories; magnesite brick probably has four times its heat conductivity. The coke oven needs bricks of high heat conductivity. Any process which would increase the heat conductivity of silica brick would undoubtedly shorten the coking process.

Jan 12, 1915

By A. G. Crocker

The positions of twin reflections in electron-dijjcraction patterns obtained from thin metal foils may he calculated for any twin in any crystal structure by means of an elementary application of vector algebra, General equations for the four classical orientation relationships are presented using the superscript and subscript notation of the tensor calculus, which is briefly described. As an example of the application of these expressions, the case of twinned rhomhohedral crystals, and hence as a special cased twinned cubic crystals, is examined. CONSIDERABLE interest has recently been shown in the interpretation of electron-diffraction patterns obtained from twinned regions of thin metal foils. In the present paper, it is shown that the necessary information may be obtained directly for all twins in any crystal structure by means of a very elementary application of vector algebra. The equations involved are most conveniently presented by making use of the very powerful superscript and subscript notation of the tensor calculus. The use of this notation will first be described and then applied to the problem of calculating diffraction patterns for any twinned crystal. Finally, as an example of the application of the method, the specific case of twinned rhombohedra1 crystals will be considered.

Jan 1, 1965

As the radical element has secured control of the various local printers' unions of New- York City, 250 magazines have temporarily suspended publication rather than grant their demands. The actions of. these local unions have been repudiated by the officers of the different inter-national unions, who are seeking in every way to carry out their agree-ments with the publishers. The charters of the local pressmen's and feeders' unions have been revoked by the international officers and new local unions are being formed. Members of the typographical union are not, as yet, directly affected by the strike, but many of them are taking "vacations," which accomplishes the same purpose as the strike but without the odium. The Engineering and Mining Journal, with true engineering spirit refusing to admit insuperable obstacles, is sending out a two-page printed market bulletin, together with two typewritten pages, making an an-nouncement of its predicament and giving brief items of mining news. Thus s brought home to the members of the mining profession in a very direct way the pernicious results of unrestrained control of labor organi-zations-by foreign and un-American elements. No sermon on this sub-ject is required, as the facts themselves are sufficiently eloquent.

Jan 11, 1919

The State Mining Bureau of California under the direction of Fletcher Hamilton, State Mineralogist, is starting a field campaign to report on the economic minerals of California, which have an important industrial and military bearing on the present war situation. Particular interest and value attaches at the present moment to our available supplies of chrome, coal, iron, magnesite, manganese, molybdenum, quicksilver and tungsten. Trained geologists and engineers of the Bureau's staff are being sent, out to obtain information with relation to the latest developments. Advance notices will be sent to the local newspapers, from time to time, of the arrival of the engineers in the various districts. All persons interested in the minerals mentioned are earnestly urged to cooperate with the State Mining Bureau by meeting the field men while in their districts or by communicating direct with the State Mineralogist at his office in the Ferry Building, San Francisco. The State Mining Bureau has just issued Bulletin No. 72 on The Geologic Formations of California. It was written by Prof. James Perrin Smith of Stanford University, and contains a complete bibliography and resume of all of our present knowledge relative to the geological formations occurring in California. It also contains much previously unpublished data, and six tables showing geologic columns. It covers 41 pages.

Jan 6, 1917

By Frank C. Greene

Drilling for oil and gas in Missouri continued at a slightly lower rate than has been prevailing. A summary of operations for the past few years as compiled and published by the Missouri Geological Survey and Water Resources is as follows: Two oil pools are being developed in Cass County. Neither area has been drilled completely, and detailed descriptions will not be given at this time. In the Endicott pool in the southern part of T. 44 N., R. 33 W., oil is found in the Warrensburg sand, which is now considered to be the Big Lake sand of eastern Kansas. The top of the sand is about 125 ft. below the Herthalimestone. The best well is reported to have made 14 bbl. per day for the first four days. The oil is 30" to 32' BB. gravity. This is the only pool in the state, aside from the older areas on the east and west edges of Lees Summit, Jackson County, that is producing oil from the Warrensburg sand. Drilling continues in the Knoche pool in the central part of T. 46 N., R. 33 W., where the oil is found in the Squirrel sand. The oil produced by both these pools is sold by truck in Kansas City.

Jan 1, 1937

By W. P. Rawles

In the foreword by C. K. Leith, Chairman of The Mineral Inquiry, it is pointed out that the ordinary mineral production tables do not show the commercial control, and that some knowledge of the situation is desirable as a background for the consideration of problems involving mineral raw materials. The report consists principally of tables, accompanied by a brief text, giving the production and an analysis of the control, according to nationality, of 18 minerals: aluminum, chromite, copper, iron and steel, lead, manganese ore, mercury, molybdenum, nickel, nitrates, petroleum, potash, silver, sulfur, tin, tungsten, vanadium, and zinc. For the most part, the production figures for 1929 and the latest figures for reserves have been used. When feasible, the control has been shown at the various stages of production; mining, smelting and refining. American capital was dominant in the production of 10 mineral commodities, including six of the most important; British capital, in four instances; while Spanish, German, Chilean or Chinese interests cach led in the control of one. British, French, German, and Dutch capital occupied second place in the control of most of the important minerals. Between two-thirds and three-fourths of the world's mincral production is controlled by British and American capital.

Jan 1, 1934

A permanent exhibition of mining machinery has just been opened in the Grand Central Palace, New York City. The exhibits include: Aerial tramways, amalgamation, assaying and laboratory appliances and supplies, blast furnaces, coal, coal-breaker plant, coal excavation, coal products, compressed-air plant, concentrating, crushing, cyanidation, distillation, drainage and pumping, drilling, earth excavation, electrical supplies, explosives, fire prevention, flotation, general supplies, hoisting, hygiene, welfare, iron products, leaching, mechanical conveyors, metal products, natural gas, petroleum, petroleum products, electric, steam, hydraulic, gas, air, and internal-combustion engines, power machinery, preparation of coal, pumping, refining, roasting, rock excavation, rotary drilling; boring, safety appliance, screening and washing, sizing and classifying, smelting, storage of coal, storage of petroleum, surface transportation, surveying, underground timbering, underground trans-port, ventilation, mine. This exposition is operated by the Merchants and Manufacturers Exchange of New York for the purpose of showing under one roof all lines of machinery and mechanical appliances. As for as possible, the exhibits will be shown in operation. The Advisory Committee is as follows: General Howard R. Ward and H. C. Parmelee. Coal and Coke.-Prof. H. H. Stoek, Samuel A. Taylor, Edwin Ludlow. Petroleum and Gas.-Frederick G. Clapp, Ralph Arnold.¬ Extraction of Metals.-Charles W. Merrill, E. Gybbon Spilsbury. Refractories.-Kenneth Seaver.

Jan 12, 1919

We, the undersigned, being all persons of full age and citizens of the United States and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I of said law, the existing unincorporated association known , as American Institute of Mining and Metallurgical Engineers, Incorporated, do hereby make, acknowledge and file this Certificate for that purpose, and do certify as follows I That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained II That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council, that the undersigned are all members of said Council as the same was constituted on the 29th day of December, 1904

Jan 1, 1952

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Superintendent for iron mine operated on the sub-level and caving system. Small output, moderate salary. Location, Southern State. No. 45. Chemist to sample and analyze iron ore. Experience in other branches not essential. Location, Southern State. No. 46. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introducd by members.) Experienced mine superintendent desires position. Several years' experience in practical management of mining and development work. Has also practiced ass consulting engineer and is thoroughly experienced in the examination and development of mining properties. Mexican experience. Will go anywhere for reliable concern. Salary moderate. References. No. 254. Member, mechanical superintendent, wants position. Has had 12 years' experience as master mechanic of smelting plants in United States and Mexico. Also superintendent of shops doing marine, mining, and general contracting work. . Experienced in manufacture of mining tools and equipment. Up to the minute in copper, lead, and zinc smelting. Has learned a learned a great deal, can forget much, and has the inclination and ability to learn more. Best of references. No. 255.

Jan 10, 1915

By L. L. McDaniel

ROLLER—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By F. F. Poland

S. ROLLE*—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

The following petition for amendment of the constitutional provisions relating to qualifications for membership in the Institute, signed by 75 members, of whom 27 are members of the Committee on Increase of Membership, was received by the Board of Directors, was printed on the program of the New York Meeting sent to all members early in January, and is now being voted upon by the membership: In accordance with the terms f Article X, we hereby propose the following amendment to the Constitution, Article II, Section 2: Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in addition thereto, all those thereafter, elected or transferred into the, class of Members. A person to he eligible for election or transfer into the class of Members must he at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence.

Jan 2, 1918

CERTIFICATE OF INCORPORATION [AMENDED Nov 22, 1912, AND JUNE 27, 1919 ] WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I of said law, the existing unincoiporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows I That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained II That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council, that the undersigned are all members of said Council as the same was constituted on the 29th day of December, 1904

Jan 1, 1923

In the fall of 1937, the Department of Mining at Penn State was being reorganized and the department records were moved to the Records Room of the School. An inventory of the contents of the vault disclosed six folders of records that had been forgotten for 27 years. These files, apparently preserved by former Dean W. R. Crane, plus the recollections of several former members of the Association described below, unfolded the "lost chapter" in mineral industries education.1 It was apparent at an early date in technical education that an association of mining schools with common interests and problems would have definite value. By 1902 sufficient interest had developed in this idea to cause the holding of a preliminary meeting for the purpose of organization. The first meeting was held at the Montana School of Mines on September 4, 1902. At that time, officers were elected and resolutions were adopted that there be formed an organization to be known as the National Association of State Mining Schools. The object and purpose of this Association was to advance the interests of state mining schools in every way, particularly by promoting legislation for the benefit of such schools. The second meeting was held September 10, 1903, and a resolution was passed that the American Mining

Jan 1, 1950

Seventeen members of the Board were present, and the Secretary of the Institute. During part of the meeting, seven other Members of the Institute were also present as guests. After extended discussion, the Board approved the general principles embodied in the War Minerals bill, and recommended the passage of a bill embodying these principles. The vote stood 14 in favor and two opposed, one member not voting. On motion, duly seconded, it was RESOLVED, that in connection with the appointment of the proposed War Minerals Administrator, the attention off the War Minerals Committee be called to the importance of selecting a man trained in the mining and metallurgical industry, but having no pecuniary interest in these industries. John V. N. Dorr was elected Director to fill the vacancy caused by the election of Robert M. Raymond as Vice-President. Charles W. Goodale was elected First Vice-President. George C. Stone was elected Treasurer. Rossiter W. Raymond was appointed Secretary Emeritus. Bradley Stoughton was elected Secretary. The following committees were elected: Executive Committee, Finance Committee, Committee on Papers and Publications, Committee on Membership, Library Committee, Committee on Nominations, Committee on Safety, Sanitation and Welfare. John V. N. Dorr was appointed Chairman of the Committee on Increase of Membership.

Jan 4, 1918

Note by the Secretary.-—In the preceding communication of Mr. Rickard, in the present discussion, as printed in Trans., xxiii., the loss of quicksilver at Pestarena, reported on p. 569, as 230 and 234 grammes per metric ton, is stated as equivalent to about 74 pounds per short ton avoirdupois—an obvious error, which escaped correction in my reading of the proofs, and was not discovered until after Vol. XXIII. had left the press. The true equivalent is 0.46 pound or about 7 1/2 ounces (instead of pounds) per short ton.— R. w. R. Philip Argall, Denver, Colo. (communication to the Secretary) : Mr. Rickard's last contribution to this discussion* calls for some reply from me, if only by way of defending myself against the charge (p. 569) that my criticisms of his paper were "unnecessarily hypercritical and occasionally unfair." At the same time I am fully aware that our Transactions are not the place for mere personal controversy, and that the sole object of discussion is to define differences of opinion, and defend opposing views as a means of eliciting the truth. Mr. Rickard disclaims the statement, which he says I attributed to him, that in the slow-crushing Gilpin county mills the pyrites remain longer in the mortar than the other portions of the ore. My understanding of his statement was based on the following passages in his paper: " Particles of ore, which have heen pulverized to a fineness which would permit of their exit through the screen, are enabled to settle towards the bottom of the mortar. It would he expected that the heavy metallic minerals occurring in the ore would, because of their greater specific gravity, be most affected by this feature of the treatment. In practice this is found to be so. The fine slimes contain a large proportion of metallic sulphides, generally valuable on account of their close association with the precious metals, while the coarsest particles to be found in the tailings usually consist of quartz and other minerals forming the less heavy gangue (Trans., xxiii., 139).

Jan 1, 1895

By H. A. Gardner

THE principal use of barium sulphate is as an inert paint pigment.. For this purpose, the ground material is used both in its natural and in its artificial forms. Probably the largest amount is used in the production of a chemically precipitated pigment called lithopone which consists of 70 parts of barium sulphate and 30 parts of zinc sulphide. An enormous tonnage-of this pigment is at the present time being used in the manufacture of interior flat wall paints of the oil type, such paints having almost entirely supplanted the use of corroded white lead which was at one time used for interior painting. The more dense nature, lower price and sanitary value of lithopone was responsible for this change. Lithopone is, moreover, used to a large extent in the manufacture of oil cloth, shade cloth and linoleum. Its whiteness makes it of particular value for this purpose. Barium sulphate is also used of itself in admixture with other pigments in the manufacture of prepared paints. The chemically precipitated form of barium sulphate, which is generally called blanc fixe, is also used for this purpose. Much controversy has raged in the paint world over the question of inert pigments such as barytes, silica, asbestine and china clay. These pigments are probably called inert because they have no chemical action upon the linseed oil in which they are ground to produce paints, and on account of the fact that they become transparent in oil. It is well known that in the manufacture of paints, opaque white pigments, such as basic carbonate white lead, basic sulphate white lead, zinc oxide etc., are generally used as the grinding base. These base pigments, when ground in oil, react therewith to some slight extent, and they produce white paints which have excellent biding or obscuring value. The inert pigments so-called, when ground in oil and spread out into a thin film, form transparent coatings which have no hiding power. It has been contended, therefore, that the use of barytes or similar inert pigments in paints is resorted to simply for the purpose of cheapening the cost of the product.

Jan 9, 1914

By W. A. Thomas

STEAM is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 lb., are used for power out of each ton produced.

Jan 9, 1921

By Thomas M. Drown

I DESIRE to communicate to the Institute the results of a few analyses which bear on the condition of carbon in gray and white iron. These analyses were made in the course of an investigation, now in progress, of the chemical composition of "chilling" irons. It will be remembered that Bell says he found no material difference in the amount and condition of carbon in gray and white pig iron made at the Clarence furnace, in England, and he therefore refers the difference in color and appearance in these two varieties of iron to the size of the particles of graphite. I quote from his "Chemical Phenomena of Iron Smelting:" "The inference I would draw from the information afforded by these analyses is, that the condition of iron in respect to its so-called 'richness' is, within certain limits, entirely independent of its chemical constitution.. .. In the fluid state, I conceive the carbon, so taken up, confers upon the iron the property of fusion much below the temperature at which the pure metal melts, and the carbon itself may be regarded as dissolved in the iron. If, during the process of manufacture, the pig metal has been formed at a low temperature, consolidation, I imagine, takes place under such circumstances that the crystals are so minute, and the carbon which is separated assumes the uncombined or graphitic form in particles so minute as to be invisible, and, in consequence, the iron is white. If, on the other hand, the furnace is working at a very high temperature, the intensely heated iron crystallizes with large facets, upon which the extruded carbon assumes the condition of distinct plates or flakes. Should the temperature be less intense, these crystals are of smaller dimensions, and the separated carbon is less conspicuous, and, as the temperature of the furnace declines, the crystals decrease in size, as do the flakes of carbon, until both disappear in white iron.. .. Returning, then, to temperature as the cause of differences in quality of pig iron, the 'chilling' of gray metal, and its conversion into white, may be regarded as the effect of preventing, by rapid cooling, the formation