Search Documents

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.' Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

Organization Place Date 1913 Mining and Metallurgical Society of America New York, N. Y. Jan. 8 American Institute of Electrical Engineers New York, N. Y. Jan. 11 American Society of Civil Engineers New York, N. Y. Jan. 22-25 American Society of Heating and Ventilating Engineers : New York, N. Y. Jan. 22-25 American Institute of Mining Engineers New York, N. Y. Feb. 18-21 National Society for Promotion of Industrial Educa- tion New York, N. Y. Feb.. American Institute of Architects Washington, D. C. April American Iron and Steel Institute New York, N. Y. May New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. American Chemical Society Cleveland, 0. Sept.

Jan 1, 1918

By Benjamin Gi ldersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than 1/2 in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000.

Jan 1, 1950

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969

PRESIDENT AND DIRECTOR EUGENE MCAULIFFE OMAHA, NEBR. PAST PRESIDENTS AND DIRECTORS HERBERT G. MOULTON NEW YORK, N. Y. JOHN R. SUMAN HOUSTON, TEXAS TREASURER AND DIRECTOR H. T. HAMILTON NEW YORK, N. Y. VICE PRESIDENTS AND DIRECTORS ERLE V. DAVELER NEW YORK, N. Y. W. M. PEIRCE PALMERTON, PA. PAUL D. MERICA NEW YORK. N. Y. LEROY SALSICH DULUTH, MINN. CHESTER A. FULTON NEW YORK, N. Y. L. E. YOUNG PITTSBURGH, PA.

Jan 1, 1942

Jan 1, 1886

By PERCY E. BARBOUR

SECONDARY copper1 has &come more or less of a bugbear generally. What is its influence is often the subject of heated argument. The inedapable fact usually quoted is that since in 1929 primary production of copper in the United States was 1,026,348 tons and secondary production was 626,550 tons, there- fore, 0.6 lb. of secondary is produced for every pound of primary, and "How can you get around that?" The matter seems very plain, now that I have reached my conclusions, but they are the result of much laborious study and research. I shall show that' the production of secondary copper is not 0.6 per lb. of primary, in spite of statistical appearances; that the production of secondary is a function of primary production rather than of price; that secondary production has 'only a sub-. ordinate influence on the price of copper and then only in abnormal times; that there is not an accumulating reservoir of secondary from which the country is some- time to be drowned in copper, as is believed by some, or a reservoir from which we are going to draw much needed and more or less inexhaustible stores in the future, as is believed by others; and finally, that the United States always produces more copper than it uses and exports the surplus. These are all controversial points, and for that reason and to anticipate argument I have set forth my reasoning in considerable detail.

Jan 1, 1931

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

Jan 1, 1886

PRESIDENTS L. D. RICKETTS, NEW YORK, N. Y. PAST PRESIDENTS BENJAMIN B. THAYER, NEW YORK, N. Y. WILLIAM L. SAUNDERS, NEW YORK, N. Y FIRST VICE-PRESIDENT SIDNEY J. JENNINGS, NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y.

Jan 1, 1917

PRESIDENT BENJAMIN B. THAYER, NEW YORK, N. Y. PAST PRESIDENTS JAMES F. KEMP, NEW YORK, N. Y. CHARLES F. RAND, NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS, NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y.

Jan 1, 1917

By D. Harrington

ANNUAL or necessary inspections and investigations of coal mines for various purposes were made possible through the Federal Coal Mine Inspection Act of May 7, 1941, which authorized entry to the Secretary of the Interior through the Bureau of Mines. Primary object of these inspections is to obtain information pertaining to health and safety conditions. Among the purposes for which the data are to be used, are annual reports to Congress, the publication of inspection reports, and the compilation and publication of statistics. The act states that inspections and investigations shall be made by employees of the Bureau of Mines, who shall co-operate with other bureaus of the U. S. Department of the Interior, as well as with the official mine-inspection, safety cr health agencies of the several states and territories. The act specifies that a coal-mine inspector shall have "the basic qualifica-

Jan 1, 1946

COMMITTEES. Iron and Steel. Albert Sauveur, Chairman. A. A. Stevenson, Vice-Chairman. Herbert M. Boylston, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. LOCAL COMMITTEES. Program Committee.-A. A. Stevenson, Chairman. Herbert A3. Boylston, J. E. Johnson, Jr., Henry D. Hibbard, E. Gybbon Spilsbury. Reception Committee.-J. R. Johnson, Jr., Chairman. Felix A. Vogel, William R. Walker. Dinner Committee.-E. Gybbon Spilsbury, Chairman. The opening session was held on Thursday morning, Oct. 16, 1913, at the Institute Headquarters in the Engineering Societies Building, 29 West 39th Street, New York, N. Y., and was called to order by President Rand, who addressed the meeting briefly before presenting Albert Sauveur, who responded to the President's address, and presided at the meeting. The following papers were then presented in oral abstract by their authors or authors' representatives: The Cleaning of Blast-Furnace Gas, by W. A. Forbes. Discussed by S. K. Varnes, H. N. Diehl, F. H. Wagner, Joseph Hartshorne, S. B. Marshall, J. W. Richards, J. E. Johnson, Jr., W. A. Forbes, and others.

Jan 12, 1913

For the year ending February, 1923 PRESIDENT ARTHUR S. DWIGHT, District 0 NEW YORK, N. Y. PAST PRESIDENTS HERBERT HOOVER, District 4 WASHINGTON, D. C. EDWIN LUDLOW, District 0 NEW YORK, N. Y. FIRST VICE-PRESIDENT J. V. W. REYNDERS NEW YORK, N. Y. TREASURER CHARLES F. RAND NEW YORK, N. Y. SECRETARY FREDERICK F. SHARPLESS,. . . . . NEW YORK, N. Y. ASSISTANT SECRETARY PERCY E. BARBOUR NEW YORK, N. Y.

Jan 7, 1922

By S. H. Chauvenet

Jan 1, 1882

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By S. H. Penn

One of the more challenging aspects of the unfolding age of space travel centers about the opportunity for man to use the natural resources of other worlds. The first of the extraterrestrial worlds to be exploited will be the moon. After only a scant few thousand years of scratching the earth's crust, man will embark upon a venture that for centuries has excited the imagination of many (while staggering that of most) and may become a reality within the next decade. There has never been a time when so much money and effort will have been expended to exploit an area about which so little is known. Paradoxically, this effort combines much of the detached objectivity so typical of our analytical time with the proverbial optimism of the indefatigable prospector. As the earliest manned lunar missions will be brief and exploratory in nature, astronauts will not be expected to attempt to exploit any of the possible lunar natural resources. In later missions, with a more extended period of time available for the astronauts to stay on the moon, it may be desirable or even necessary to "live off the land". The resulting exploitation of lunar resources will be intended primarily to reduce the dependence of manned missions upon terrestrial logistic support and to reduce the cost of maintaining lunar bases.

Jan 3, 1966

By AIME AIME

THE American Institute of Mining and Metallurgical Engineers will hold its annual meeting in New York City, Feb. 9-12. The technical sessions, excepting the Sunday afternoon and evening sessions of the Mineral Industry Education Division (see the M.I.E.D. program) will be held in the Engineering Societies Building. The "All-Institute" luncheon on Monday will be at the Commodore Hotel; the Annual Banquet and President's Reception, the Smoker, and the Informal Dance will be at the Waldorf Astoria Hotel. The dinners of the Petroleum Division and the Institute of Metals Division will be at the Roosevelt Hotel.

Jan 1, 1942