Search Documents

By H. E. Stamm, H. H. Spain, R. C. Rumble

This paper presents a reservoir analyzer study of the performance of the Woodbine formation in the East Texas basin. The study was made possible by the compilation of available information on the configuration. thickness and the pressure drawdown of the formation. The investigation was made of the pressure variations in the basin incident to production from the several Woodbine reservoirs. In addition, the apparent compressibility of Woodbine water was evaluated so that the potential water yield of the formation could be determined. The distribution of permeability of the Woodbine sand and the interference between producing areas were also investigated. In conjunction with this basic study of the Woodbine sand, an acceptable match of the production-pressure relationship in the East Texas Field was established on the analyzer. INTRODUCTION When production is taken from a reservoir contiguous to an aquifer, the resultant pressure gradient causes a water influx into the reservoir. For some years it has been the practice to predict the performance of water drive reservoirs with mathematical equations that relate the water influx into reservoirs to their pressure behavior. A rigorous solution of these equations is quite complex: hence, the conventional method requires the simplifying assumptions that the formation have constant thickness, permeability and poiosity, and that it have a known and regular shape. It is necessary to use performance records of the reservoir in question to determine the equation constants that make the results of the mathematical calculations duplicate the reservoir history. The values of the constants determined in this manner sometimes differ so greatly from theoretical or measured values that the constants appear unreasonable. The equation constants comprise such factors as the thickness, porosity and permeability of the formation, and the viscosity and compressibility of water. Usually the thickness, porosity and viscosity are known within a reasonable degree of certainty. whereas the formation permeability and the water compressibility are known with considerably less certainty. Hence. permeability and compressibility values are arbitrarily selected that will make the mathematical equations duplicate the reservoir behavior. In many reservoir studies the value of the compressibility of water thus selected has exceeded the reported value by a factor of from severalfold to manyfold. Whether this excessive value results from the inadequacy of the mathematical approach to take into account the shape irregularities and the heterogeneities of the aquifer, or is due to some type of formation compaction and decrease of porosity has not been established. Because of the significance of the potential water yield of formations with reference not only to oil reservoirs but to water resources as well, it is very important that a representative value for the effective water compressibility be determined. One of the best known examples of a field for which it has been possible in the past to predict the future reservoir pressure is the East Texas Field. Until about 1943 it was possible by means of mathematical equations to duplicate past pressure behavior and to predict with a high degree of accuracy the reservoir pressure of the field. Since 1943, however, the calculated pressures have deviated progressively from the observed pressures to such a degree that in recent years, it has

Jan 1, 1951

By H. H. Spain, R. C. Rumble, H. E. Stamm

This paper presents a reservoir analyzer study of the performance of the Woodbine formation in the East Texas basin. The study was made possible by the compilation of available information on the configuration. thickness and the pressure drawdown of the formation. The investigation was made of the pressure variations in the basin incident to production from the several Woodbine reservoirs. In addition, the apparent compressibility of Woodbine water was evaluated so that the potential water yield of the formation could be determined. The distribution of permeability of the Woodbine sand and the interference between producing areas were also investigated. In conjunction with this basic study of the Woodbine sand, an acceptable match of the production-pressure relationship in the East Texas Field was established on the analyzer. INTRODUCTION When production is taken from a reservoir contiguous to an aquifer, the resultant pressure gradient causes a water influx into the reservoir. For some years it has been the practice to predict the performance of water drive reservoirs with mathematical equations that relate the water influx into reservoirs to their pressure behavior. A rigorous solution of these equations is quite complex: hence, the conventional method requires the simplifying assumptions that the formation have constant thickness, permeability and poiosity, and that it have a known and regular shape. It is necessary to use performance records of the reservoir in question to determine the equation constants that make the results of the mathematical calculations duplicate the reservoir history. The values of the constants determined in this manner sometimes differ so greatly from theoretical or measured values that the constants appear unreasonable. The equation constants comprise such factors as the thickness, porosity and permeability of the formation, and the viscosity and compressibility of water. Usually the thickness, porosity and viscosity are known within a reasonable degree of certainty. whereas the formation permeability and the water compressibility are known with considerably less certainty. Hence. permeability and compressibility values are arbitrarily selected that will make the mathematical equations duplicate the reservoir behavior. In many reservoir studies the value of the compressibility of water thus selected has exceeded the reported value by a factor of from severalfold to manyfold. Whether this excessive value results from the inadequacy of the mathematical approach to take into account the shape irregularities and the heterogeneities of the aquifer, or is due to some type of formation compaction and decrease of porosity has not been established. Because of the significance of the potential water yield of formations with reference not only to oil reservoirs but to water resources as well, it is very important that a representative value for the effective water compressibility be determined. One of the best known examples of a field for which it has been possible in the past to predict the future reservoir pressure is the East Texas Field. Until about 1943 it was possible by means of mathematical equations to duplicate past pressure behavior and to predict with a high degree of accuracy the reservoir pressure of the field. Since 1943, however, the calculated pressures have deviated progressively from the observed pressures to such a degree that in recent years, it has

Jan 1, 1951

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper' that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,' was not adequate for this study.

Jan 1, 1965

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By Takao Kobayashi

Micro-crack formation zones developed near a crack tip in rocks and ceramics play a significant role in fracture behavior of these materials. In order to study micro- crack formation near a crack tip and its effects on crack behavior, a mica-epoxy composite material was developed. Multi-layer mica flakes were embedded in an epoxy matrix. Under high stress in the vicinity of a crack tip the mica delaminated, simulating the micro-cracking along grain boundaries or crystal planes in rocks and ceramics. A compact tension specimen was fabricated from mica-epoxy composite material. During the test the load and crack opening displacement were measured following the ASTM E561 (R-curve determination) procedure. Through the compliance calibration method the effective crack length and the KR were computed. The experiment clearly demonstrates the formation of micro-cracks and their effects on the overall behavior of the specimen. The paper discusses the significance of micro-crack formation on fracture toughness characterizations, and the advantages of the use of mica-epoxy composite for detailed studies of interaction between the micro-crack formation zone and the specimen geometry and size.

Jan 1, 1982

By A. F. Crawley

The densities of some liquid Pb-Sb alloys up to 11 wt pct Sb and Pb-Sb-& alloys up to 10 pct Sb/10 pct Sh have been determined by a pycnometric technique over a temperature range of about 130°C above their melting points. The data given are accurate within 0.05 pct. Density is shown to vary linearly with temperature , and equations relating these quantities have been formulated. Molar volumes calculated from the density data indicate that volumetric deviations from ideal mixing are undetectable within the limits of experimental error. A continuing research program into some fundamental physical properties of liquid metals is being pursued at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This work has received support from the Canadian Zinc and Lead Research Committee in cooperation with the International Lead and Zinc Research Organization. This paper, which reports some density data for Pb-Sb and Pb-Sb-Sn alloys, follows previous work from this laboratory on lead, tin, and Pb-Sn alloys.' Of previous data from others, Greenaway2 and Sato and Munakata3 have reported results on Pb-Sb alloys. No previous work has been published on the ternary Pb-Sb-Sn alloys, reported here. EXPERIMENTAL METHOD Densities were measured by a pycnometric technique which has been described in detail and appraised for accuracy in earlier Mines Branch reports.475 Fig. 1 shows the densitometer with the pycnometer in position for a run. The pycnometer is also shown in some detail. The pycnometer of dense, high-purity graphite, about 14 cu cm in volume, was carefully machined to a uniform, smooth finish. The height was measured by a depth micrometer and the diameter by fitting precision gage blocks between steel balls.' In each case several readings were taken, and the final results were considered accurate within 0.01 pct. The resulting volumetric uncertainty together with small inaccuracies in the coefficients of linear expansion of graphite lead to a maximum systematic uncertainty in the method of ±0.03 pct. As shown in Fig. 1, the pycnometer lid is a threaded cap. Thus, the charge, a cylinder of the alloy, can easily be inserted and the solidified metal can readily be removed after a run. The dimensions of the cylindrical charge are chosen to ensure that, once molten, the metal will not only fill the pycnometer completely but will discharge an excess into the excess-metal float chamber. AS the temperature is increased above the melting point, the volume of metal in the excess chamber increases until the system has equilibrated at the desired temperature. At this point, the excess chamber is moved to one side by twisting the shaft F, leaving a fixed volume of liquid metal in the pycnometer. This volume of fluid is readily calculated using measured coefficients of linear expansion of the graphite which expands anisotropically. The associated weight of fluid is determined as the weight of the solidified metal removed after the furnace has cooled down. Alloys were prepared from 99.997 pct Pb, 99.999 pct Sn, and 99.999 pct Sb, being melted by an electric furnace in a graphite crucible and poured into graphite molds. Several density specimens of the same nominal size were machined from each ingot, and, by comparing specimen weights, relative differences in specimen composition resulting from segregation in the ingots could be detected. In this way, segregation was found to have occurred in Pb-Sb alloys at compositions beyond the eutectic (11.2 pct Sb) and this

Jan 1, 1969

By N. S. Keith

No one of the live subjects of the day, to which the attention of the mining engineer and metallurgist should be turned, is of greater practical interest to him than electricity in its applications to various mechanical, chemical, and metallurgical operations. The object of this paper is to call the attention of my fellow-members and associates of the Institute to various new, as well as comparatively old, developments in the science and art of electricity which seem to promise results of advantage. Too many of the comparatively old applications have been neglected by the mining engineer, which; if he had given them a place among his appliances, would have assisted him greatly. The telegraph may be noticed as one. Its. use is, however, confined to a person having skill in the. manipulations of the key, the reading of the alphabet, and familiarity with the sounder. One of the simpler forms-the call-bell-has a range of application far greater as to distance and convenience than the old wire-pull, or the hoarse voice of the windlass-man or the bucket-dumper. A few Leclanehé cells, two or more electric bells, and a mile or more of wire judiciously placed will put the superintendent, at his office, in communication with the foremen of his mills and mines, so that by the aid of a code of signals, great advantages may be gained without necessitating a knowledge of the Morse alphabet, or of the mechanical voice of the sounder. The telephone furnishes a means of communication be-

Jan 1, 1882

By J. E. Wilson, F. P. Lebar

TYPICAL of southwestern Wyoming are coal structures that dip from 4° to 17°. Those at the Reliance and Winton mines of the Union Pacific Coal Co. average 91/2 and 15°, respectively, and dip almost directly to the west. By using a hoist for main haulage, a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 ft. a two-entry system is driven to the north and to the south. In both fields, which are nongassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy loader was introduced into The Union Pacific Coal Company's operations, slopes, aircourses, and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 ft. and entries at 230 ft. Connections to the workings above were made by driving up the pitch 75 ft. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a I¼-in. hemp rope dou- bling around it and having me end attached to the car and the other to the mule. The mulc, pulling downhill, raised to the working face a small wooden car of one-ton capacity. With the introduction of mechanical loading, mule haulage and small wooden cars disappeared and auxiliary hoists, electric locomotives, and steel cars with a capacity of 4 tons were substituted. Development work was done during two or three shifts of the 24-hr. period. Driving of haulage slopes down the pitch by hand continued. Crosscut intervals were changed to Ioo ft. and the crosscuts were driven with shaking conveyors. With the use of a 90° swivel, aircourses and manways were driven up the pitch. Entry intervals were changed from 230 ft. to 300 feet. Mobile loaders of the Joy type were first employed by this company in the year 1923 at Hanna, Wyo. In 1928, two 4-BU Joy loaders were transferred from Hanna to Winton No. I mine, where they were used in driving slopes and entries. At the time of transfer, the machines were about worn out and were not suited to the steep pitch, therefore frequent breakdowns occurred. However, experience justified the belief that the mobile loader was fitted for driving slopes in this field. During 1937 a unit was installed in Reliance No. 7 mine, and during 1939 one in Winton No. 7½ mine. With the introduction of this type of mobile loader, a new era of development began. Speed undreamed of in hand-loading days became a reality. The cost of development down the pitch has been reduced until it

Jan 1, 1942

By J. E. Wilson, F. P. Lebar

TYPICAL of southwestern Wyoming are coal structures that dip from 4° to 17°. Those at the Reliance and Winton mines of the Union Pacific Coal Co. average 91/2 and 15°, respectively, and dip almost directly to the west. By using a hoist for main haulage, a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 ft. a two-entry system is driven to the north and to the south. In both fields, which are nongassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy loader was introduced into The Union Pacific Coal Company's operations, slopes, aircourses, and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 ft. and entries at 230 ft. Connections to the workings above were made by driving up the pitch 75 ft. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a I¼-in. hemp rope dou- bling around it and having me end attached to the car and the other to the mule. The mulc, pulling downhill, raised to the working face a small wooden car of one-ton capacity. With the introduction of mechanical loading, mule haulage and small wooden cars disappeared and auxiliary hoists, electric locomotives, and steel cars with a capacity of 4 tons were substituted. Development work was done during two or three shifts of the 24-hr. period. Driving of haulage slopes down the pitch by hand continued. Crosscut intervals were changed to Ioo ft. and the crosscuts were driven with shaking conveyors. With the use of a 90° swivel, aircourses and manways were driven up the pitch. Entry intervals were changed from 230 ft. to 300 feet. Mobile loaders of the Joy type were first employed by this company in the year 1923 at Hanna, Wyo. In 1928, two 4-BU Joy loaders were transferred from Hanna to Winton No. I mine, where they were used in driving slopes and entries. At the time of transfer, the machines were about worn out and were not suited to the steep pitch, therefore frequent breakdowns occurred. However, experience justified the belief that the mobile loader was fitted for driving slopes in this field. During 1937 a unit was installed in Reliance No. 7 mine, and during 1939 one in Winton No. 7½ mine. With the introduction of this type of mobile loader, a new era of development began. Speed undreamed of in hand-loading days became a reality. The cost of development down the pitch has been reduced until it

Jan 1, 1942

By J. B. Wagstaff

The raceway in front of the tuyere of the blast furnace has been studied quantitatively and a correlation obtained for the penetrastudiedtion of the blast. Some evidence is presented for the height and width of the raceway which suggests that all the raceways of a ffurnace overlap. The size of the coke in this zone has been measfurnaceoverlap.ured photographically during normal operation and results are given for the various areas. IN an earlier paper,' it was shown that a raceway exists opposite each tuyere of a blast furnace. This raceway is formed by the jet effect of the air emerging from the tuyere and consists essentially of a turbulence in which coke particles are recir-culated at high speed. Its presence was deduced originally from observations on movies taken with a high-speed camera through the tuyeres of various furnaces and was confirmed by experiments made on a model. In the model described,' this raceway was shown as operating in a vertical plane only, although there was a suggestion in the motion-picture film exhibited at that time that the raceway was three dimensional, unless artificially restricted. There was also some doubt then about the factors influencing its size. This paper describes the next steps in the investigation. Since the size of the raceway is obviously of importance in the operation of the furnace, it seemed worth while to study the subject more carefully. It is probably in this region that about half the coke in the furnace is consumed, so that the movement of the stock column may well be controlled by raceway behavior. Furthermore, there is some evidence to suggest that the coke is packed densely in the center of the furnace to form the "dead man" and more loosely above the raceway. It is therefore probable that the bulk of the gases passing up the stack flow from the top surface of this raceway. Clearly then, a knowledge of this critical zone is of interest to the blast furnace operator, and the first half of this report is devoted to a quantitative discussion of the subject. A further topic of interest among operators is the degree of breakdown of coke in the furnace, with which is inseparably linked the importance of a strong coke. Indeed, the whole question of the optimum size and type of coke may be as dependent on the condition of the coke in the bottom of the blast furnace as at the top. Attempts have been made from time to time to obtain samples of coke from the tuyeres and other furnace openings but they all suffer from the fact that the coke is filled to a varying degree with metal and slag and is probably broken up by the very act of taking the sample. It has proved difficult to make any reliable studies of coke size by these methods. However, it did seem possible to use the highspeed movies mentioned earlier1 to estimate the size of the coke. These movies provide an accurate record of individual coke particles so that, in theory at least, it should be possible to measure the size of the particles one by one and to obtain, for the first time, information on the coke being blown around the raceway under actual operating conditions while the furnace is performing normally. Such a study has been made and is discussed in the second half of this paper. The results obtained enabled the blast furnace data to be correlated with the model results given in the first half. Raceway Size In order to make a quantitative study of the size of the raceway it was necessary to devise some apparatus of laboratory scale, which could be handled quickly and easily. This focused attention on models, which in turn means that the laws of similarity governing this particular process must be ascertained. Method of Procedure: Since the work was to be carried out on a smaller scale than the blast furnace, the linear dimensions of the model became unimportant provided that the scale was known; it is only important to insure that the container does not affect the raceway being observed. The studies therefore were carried out in a glass-sided box, 11 in. high x 7 in. wide x 3 in. deep, using air jets ranging

Jan 1, 1954

By F. W. Lake, H. A. Brett

With each year bringing the exploration of deeper and deeper producing horizons in the effort to maintain production, the problem of lifting the oil to the surface is continually becoming more difficult. Flowing and gas-lift wells eventually decline to such a point that pumping is necessary. The increasing loads on sucker rods resulting from deeper pumping operations are approaching the ultimate strength of the rods with consequent reduction in the factor of safety. With this diminishing factor of safety, the vibratory stresses causing fatigue, crystallization, and ultimate fracture become more important. These vibratory stresses are the result of varied pumping conditions which, if properly understood and investigated, may be eliminated to a great extent. To accomplish this purpose, a recording dynameter has been developed which gives an indicator card showing the actual load on the polished rod at each point of the pumping cycle. Recording Dynamometer The instrument consists of a dynamometer head of the piston and cylinder type filled with castor oil, and a recording device, the movable card holder being connected with the dynamometer through a system of levers and the hollow spring gage connected with the fluid chamber of the dynamometer by a high-pressure flexible tube. The dynamometer head is hung from the beam with an ordinary hanger and lugs on the cylinder, while the piston is attached to the polished rod. The movable card holder actuated through levers moves in a vertical direction pro-portionate to the movement of the polished rod. The recording arm of the hollow spring gage inscribes on the card the pressure at all times. Thus by proper scales, the indicator card gives the load on the polished rod at all points in the pumping cycle. Fig. 1 shows the hookup of the recording dynamometer at a pumping well.

Jan 1, 1928

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By J. W. Marx, R. H. Langenheim

The authors are to he complimented for a timely presentation of useful information concerning application of heat to oil reservoirs to increase the rate and ultimate recovery of oil. The solution for heated area resulting from constant rate injection of a hot fluid, presented by the authors, and the fluid-flow analogy, solved by Carter,' are particularly interesting in that 110 restriction is placed on the direction of development of the heated area. It is not necessary that the heated area grow radially. Thus the solution could provide useful information for heat injection in any type of well pattern with any specified swept area data. However, it was assumed in the development that the heated region would remain at a constant clevatcd temperature. Vertical heat losses were computed on this basis. Physically. the assumption that the heated region will remain at a constant temperature (independent of distance from the injection point) appears to require that the heat injection medium be stcam, or other condensible gases near the boding point at injection pressure. If a hot liquid below the boiling point or a hot gas considerably above saturation temperature were used, the temperature of the heated region would decrease with distance from the injection well. Lauwerier2 has discussed this problem for a linear system. (See also Jenkins and Aronolsky; and McNiel and Nelson.') Thus, the authors' solution applies more nearly to steam injection than to hot water injection or hot, non-condensable gas injection. Assuming steam as the injection medium, it appears that steam would pass through the constant-temperature heated region and condense upon contact with the unheated sand. The tempcrature in the condensing region would probably be governed by the release of heat of vaporization required for phase equilibrium at the existing pressure distribution. Temperatures in the region would also be influenced by vaporization of hydrocarbon. Thus, it is doubtful that an expression for radial temperature distribution based on heat conduction only (such as the authors' Eq. 9) would have practical significance. As pointed out by Marx and Langenheim, the growth of the heated area under constant rate steam drive will eventually be limited economically by vertical heat loss. The possibility of continuing to move heat economically by cold water injection or by increasing the steam injection rate appears to be a very important consideration. (Movement of liquids away from the injection well should increase injectivity.) Fortunately, the solution presented by the authors may be generalized to thc case of a variable heat injection rate. The general solution is:

By M. F. Goudge, R. V. Tomkins

Sodium sulfate is an important chemical raw material that is being used in ever increasing quantities in modem industry. It comes on the market mainly in three forms: (1) Salt cake (Na2SO4), a relatively crude form of the anhydrous salt containing up to 3 pct impurities, and comprising about three-quarters of the North American production; (2) anhydrous sodium sulfate (Na2SO4), a refined form containing less than 0.3 pct impurities; (3) Glauber's salt, the decahydrate (Na2SO4.10H2O) containing 55.9 pct water of crystallization. Competing with salt cake from natural sources is byproduct salt cake from a number of industrial operations. For instance there is Mannheim cake resulting from the manufacture of hydrochloric acid by the reaction of salt (NaCl) and sulfuric acid in Mannheim furnaces; rayon cake, a high-quality product, resulting from the process of making rayon by the viscose process; chrome cake from the processing of sodium chromate to dichromate; phenol cake from the manufacture of phenol; also byproduct sodium sulfate resulting from the conversion of lithium sulfate to lithium carbonate; from the processing of sodium tetraborate to boric acid; from converting sodium formate to formic acid; and in the manufacture of cellophane. Sodium sulfate is also obtained as a byproduct in the manufacture of isosebasic acid. In addition strong competition has resulted from imports of byproduct salt cake from the chemical industries of a number of highly industrialized European countries. However in recent years due to technological changes the output of byproduct salt cake is rapidly diminishing and the natural deposits are becoming the most important source of sodium sulfate used in North America. For instance, the production of hydrochloric acid in Mannheim plants has become obsolete and thus the greatest single source of byproduct salt cake will disappear. Also viscose rayon is meeting strong competition from nylon and other synthetic fibers and production of byproduct salt cake from this source may do little more than remain at the present level. These factors together with increasing demand for sodium sulfate point to increased production from natural sources. In 1958, 36 pct of the total United States production was derived from natural sources and in addition 97,000 short tons was imported so that over 40 pct of the total consumption was supplied by natural sources whereas in 1953 the proportion was only 24 pct. The rapid growth in production is shown in Table 1. Principal Sodium Sulfate Minerals There are many minerals in which sodium sulfate is a constituent but those of commercial importance at the present time, and consisting wholly of sodium sulfate in either the hydrous or anhydrous states, are mirabilite and thenardite. Minerals of potential importance but consisting in part of compounds other than sodium sulfate are glauberite in which sodium sulfate is combined with calcium sulfate, and blödite in which sodium sulfate is combined with magnesium sulfate. Mirabilite (Na2SO4.10H2O) the decahydrate, consists of 24.8 pct SO3, 19.3 pct Na2O, and 55.9 pct H20. It is a colorless to opaque, soft, water-soluble mineral with a slightly bitter taste. It has a hardness of less than 2 and a specific gravity of 1.48. It forms long needle-

Jan 1, 1960

By P. R. Sahm, T. V. Pruss, D. A. Gandolfo

Cb 3 Sn powders were hot-pressed to estahlish densi-fication conditions and assess the possible use of such compacts in multiphase structures with ceramic or magnetic inclusions. Superconducting transition temperatures, Tc, were measured as a function of powder particle size, pressing temperature, and second-phase admixtures. The highest transition temperatures were found in coarse powder (5 to 500 u) compacts and were only weakly depended on pressing temperatures up to 1200°C. Fine powders (below 5 p), however, both single-phase CbsSn and Cb3 Sn-composites, showed a stronger dependence on hot-pressing temperatures. While Al2 O3 phase admixtures did not affect T, much more, a Pronounced T, degradation was observed upon the addition of ferrimagnetic Fe2 Mno. 5 Zno.5 O4 powders. Likewise, critical current densities, Jc, at 4.2° K were lowered appreciably in the ferrite doped samples, whereas the neutral A1203 inclusiow gave slightly improved Jc values. MULTIPHASE structures in electronically active materials have recently gained in interest as pointed out by Galasso in a review article.' In superconductors the most widely reported group are eutectic alloys which have been mostly investigated with respect to the proximity effect.2"4 In addition, "artificial eu-tectics", for example in the form of mercury-vycor glass sponge5 or fine niobium wires imbedded in a copper matrix,= have been prepared to attain higher critical fields and critical current densities. The idea was to enhance flux pinning phenomena by second-phase inclusions or ho1es. 7 Flux pinning should also be possible by the introduction of insulator inclusions into a superconducting matrix. Ceramic-metal combinations are most easily produced by hot pressing (= pressure sintering), as it permits an almost unlimited selection of material combinations. Cb 3 Sn has been prepared by vapor phase growths or in the form of thin films. Large compacts must be sintered,1° however, and normally present difficulties. At temperatures below 1350°C insufficient densities are obtained and at higher temperatures the loss of tin due to dissociation upsets the stoichiometry. Hot pressing is a natural approach to circumvent the problems, since one can obtain satisfactory densities despite low sintering temperatures. This work was mostly concerned with establishing conditions to hot press Cb3 Sn and Cb3 Sn multiphase structures (= composites), because no data are presently available, and to evaluate these with respect to their transition temperatures. However, a few measurements on critical current densities were also carried out, in particular to assess the value of ferrimagnetic inclusions. I) EXPERIMENTAL PROCEDURE The experimental procedure involved the preparation of feed material and powders, hot pressing, and evaluation of the resulting ingots. As no attempts were made to synthesize Cb3Sn from the elements during hot pressing, feed material had to be produced. For this purpose, a stoichiometric Cb-Sn powder mixture was compacted into a 3-cm-diam ingot (80,000 psi) and then inserted into a quartz tube and evacuated. Rf heating was employed. Above the tin melting point (230°C) liquid tin was forced out of the ingot, but was pulled back by capillary action after approximately 0.5 hr of continuous pumping at 700°C. Thus, it appears that evacuation at this temperature caused desorption of impurity gas creating wetting surfaces which, later on, favored alloying at relatively low temperatures. After a presintering period of 17 hr at 800°C, the quartz tube was tipped off and sealed into another such larger-diameter tube which, in turn, was connected to a pump system. This configuration permitted a temperature treatment at 1400°C, carried out for 65 hr, without collapsing of the glass walls or unfavorable chemical interaction of Cb3Sn with the quartz. The resulting material was

Jan 1, 1969

By S. R. Elliott

THE principles of the caving system, as they apply to mining of soft iron-ore deposits, are well known, as this method has been in use for many years. It is, however, necessary to give a general description of it before describing the Athens method. The shaft and surface equipment should be placed at a sufficient distance from the orebody, so that the caving and pulling of the surface will not disturb the operations of the mine. Levels are started at the proper intervals, and when raises are completed, slicing commences at the top of the orebody and progresses downward. The necessary precautions are taken to avoid the occurrence of large open rooms and it is customary to break sufficient capping to form a mat to prevent heavy falls of ground from crushing through to the lower sublevels and endangering the lives of the workmen. Slicing is continued, and when sufficient width and length are undercut, the capping commences to cave, and in time a settlement occurs at the surface. As soon as this caving commences, the pressure on the timber naturally increases; after it extends to the surface, the amount of pressure has a certain relation to the depth. In other words, the pressure increases with the depth, but not in direct proportion. At great depths, such as that found at the Athens, 2500 ft. (760 m.), the pressure might be so excessive that the cost of keeping working places open would be prohibitive. The actual caving of the surface in a deep mine, with a great thickness of capping, is slow and often takes years to accomplish. After sufficient width and depth -have been undercut, the capping starts to break away, but through arching large masses of rock-.fill the opening, support the capping, and retard the continuation of caving. Caving to the surface is, therefore, retarded until either a sufficient thickness of the orebody is removed, or the width and length of the undercut part have been greatly increased. I wish to emphasize this fact of slow caving, for it is on, this principle that the success of the Athens system. largely depends.

Jan 8, 1920

By James Douglas

An address before the Meeting of the New York Section, Nov. 4, 1914. As life advances one is inclined to look backward instead of forward, and the vista over which my memory carries me has been filled with such a shifting panorama of changes in metallurgy that the whole practice of the art seems to have been re-created. The first cupola furnace that I saw in operation was at one of the group of mines at Capelton, Quebec, from which the Nichols company still draws some of its sulphur supply. At that time it was operated by a Hartford, Conn., company, under a General Adams. When its small brick furnaces made a campaign of a week and smelted 10 tons a day, the feat redounded to the credit of the operator. The introduction of the water-jacketed cupola dates forward to the next decade. I was using one in Pennsylvania, making copper matte, to the horror of a noted metallurgist, who could not conceive it possible that you. could bring fused sulphides in contact with steel without rapid corrosion. In our ignorance we were doing what seemed to be an impossibility, and it is just that recklessness and disregard for precedent which has characterized so much of the work of American metallurgists, and carried us forward at such headlong speed. Once the water jacket was accepted as the type of the. copper cupola, its almost unlimited expansion in length, but not in width, was a matter of convenience rather than of skill. In Butte the cupolas have been enlarged by adding furnace to furnace. The first reverberatories which I saw in operation were those in Professor Hill's Black Hawk establishment, where the concentrates from the Gilpin County gold mills were run down into matte for separation in England. Sixty dollars per ton was the usual deduction in those days before gold and silver was paid for. Smelting was done with wood as fuel, and the capacity of the furnace was about 10 tons per diem. Shortly after this Professor Hill formed an alliance with Richard Pearce, who was running what, if I recollect aright, was called the Swansea Works, at the bend of the river approaching Georgetown.

Jan 4, 1915

By Richard A. Walker, John P. Hager

The thermodynamic properties of the Pb-Au system have been determined between 750" and 1075°C by means of the cell Mo, Pb(1) |(PbO-SiO2){l) , SiO2(s) |Pb-Au(1), Mo The activities of lead and gold exhibit negative deviations from ideal behavior; the values of ? pb and ? the raoultain activity coefficients at infinite dilution, being 0.24 and 0.25, respectively, at 1200°K. The liquidus curve for the gold-rich region of the Pb-Au phase diagram has been determined from measure-ments on seven alloy compositions in the two phase region (liquid + Au(s)). The standard free energies of formation of Au2O(l) and Ag2O (1) have been estimated from cell measurements obtained by replacing the alloy electrode with pure liquid gold and silver. A new integral molar heat of mixing curve for the liquid Pb-Au system is presented and the results of previous studies discussed. The contribution of HM to FE was found to be small relative to TSE. THE use of galvanic cells of the type A(l) |A+Za|A - B(l) [I] provides an accurate means for the thermodynamic study of liquid alloy systems. In Part 1&apos; it was shown that cells of type [I] may be extended to higher temperatures and to a wider range of alloy systems if the ion A+Za is incorporated in an appropriate molten oxide phase, rather than in the classical fused salt electrolyte. In the following investigation the experimental method is extended to an investigation of the thermo-dynamic properties of the Pb-Au system by use of the cell: Mo, Pb(l) | (PbO-SiO2)(l), SiO2(S) |Pb-Au(l), Mo [] Previous measurements on liquid Pb-Au alloys were obtained by Kleppa2 by electromotive force measurements on a galvanic cell involving a molten chloride electrolyte. These measurements were confined to temperatures less than 830°C and compositions with X Pb > 0.2 because of the instability of the cell at higher temperatures. Later measurements by Kleppa3 on the heats of formation in the composition range 0.67 < Xpb < 0.98 were not consistent with the results by electromotive force measurement. The purpose of the present study is to extend the temperature and composition range of the thermodynamic properties and to obtain an independent measure of the integral molar heat of mixing over the entire composition range.

Jan 1, 1970

"Coulter's Rainbow and Crooked Falls are situated about five miles below the City of Great Falls. Coulter's, the first of the series in the course of the river, is unimportant and has been submerged by the Rainbow dam. Next below Coulter's is the Rainbow Falls, 47 feet in height. Following Rainbow Falls is the Crooked Falls, 21 feet in height. The power developed at this point is such that the one clam, power house and tail-race utilize the power from all three of the above falls.The development at Rainbow was started October, 1908, and completed July, 1910. It has a total capacity of 21,000 k-w. in generators, and 36,000 h-p. in waterwheels, and operates at 105 foot head. The general scheme of development is typical of what may be called standard practice in the west for plants of medium head, and consists of a low diverting clam, a double pipe line feeding into a balancing reservoir near the plant, and individual pen-stocks supplying the turbines from this reservoir.The dam is a rock-filled crib structure 1,146 feet long and 29 feet high, the up-stream side of which slopes at such an angle that the stability of the clam is assured even under the greatest floods, the weight of the water acting to hold it down, so that the higher the flood the greater the stability. The down-stream side is also sloping and tapers off into a long apron so designed as to take care of any overflow which may occur without shock or commotion. The clam is founded on solid rock throughout its entire length."

Jan 1, 1913