Search Documents

By D. S. Sanders, E. W. Witcomb

FLOTATION tests, from which the flowsheet for the concentrator was determined, were made in a pilot mill at Chuquicamata and later comparative testing of full size flotation cells was done at the Andes Copper Mining Co. concentrator in Potrerillos. The principal sulphide copper mineral is chalcocite with varying amounts of covellite, enargite, and chalcopyrite. The oxidized portion is principally antlerite, a green basic copper sulphate. The gangue minerals include quartz, sericite, pyrite, feldspars and kaolin. Chuquicamata pit ores have proved to be hard grinding. The results of the flotation and metallurgical work prove that good extraction and concentrate grade can be obtained under a rather wide range of conditions. Metallurgy In general the metallurgy of the ore requires a fairly close control of the grind to the primary rougher flotation and of the regrind of the primary rougher concentrate before cleaning. Regrinding is necessary to reduce the insoluble content of the final concentrate since a large part of the middling combinations are between the copper and silica minerals. The alkalinity of the pulps can vary between wide limits and control of the percent solids gives the desired grind. Alkalinity Control Arroyo Salado water is supplied to the concentrator head tanks. It contains about 5000 ppm of salts but test work shows no deleterious effect. Actually this water permits a decrease of as much as 1 lb of lime per ton of ore as compared to San Pedro water, which is used for leaching oxide ore. About one quarter of the water flow through the concentrator will be new water from the reservoir. The remainder will be reclaimed from the thickeners. For primary grinding and rougher flotation, new and reclaimed water are combined in the head tanks. To avoid erratic results, only new water is used in the regrind system. Milk of lime is added to the rod mill feed chute to obtain the maximum benefit of mixing with the ore. This protects the equipment from corrosion due to entrained acids and soluble copper salts. Lime consumption is 3 to 5 lb per ton of ore. Grinding and Flotation The six bin gates over each belt feeder are opened in controlled combination and sequence to keep a live bed of ore in the bin to prevent arching and to obtain mixing. The milk of lime added ahead of the rod mill is regulated to suit rougher flotation requirements. The primary promoter reagent, Aerofloat 238, is added to the 10-mesh discharge of the rod mill as it is laundered to the ball mill scoop box. The classifier overflow is regulated to produce a grind of about 12 to 15 pct +65 mesh and 60 pct -200 mesh. A secondary promoter Z-4 (aml zanthate) and the pine oil frother are added in the overflow launder where a pH of 10 to 11 is maintained. Comparatively heavy beds of froth on the

Jan 1, 1952

By W. J. Houk, F. C. Hull

To clarify interpretations of grain structures and to assist in calculations of spatial grain size distributions, plane distribution curves have been determined for random sections through four regular polyhedrons approximating the shapes of metal grains. The characteristics of the distribution curve for the average metal grain are predicted. IT was realized early in the history of metallurgy that metals are polycrystalline aggregates and that the size and shape of crystals affects the properties of the material. Reaumur1 in 1722 employed the microscope to examine the fractured surfaces of steel and of white and gray cast iron and suggested a polyhedral arrangement of the crystals. The first extensive investigation of the form of crystal grains was carried out by Desch.2 He examined the disintegrated grains from a ß brass sample and noted that the number of faces per grain ranged from eleven to twenty and that the number of edges per face varied from three to eight and the maximum occurred at five. While it has been found practical to examine isolated grains only in exceptional cases, it is always possible to make a plane section through the metal and examine the shape of the grain sections on the plane of polish. Desch2 tried to determine the relation between the form of a polyhedron and that of its plane sections for comparison with distribution curves of numbers of sides per grain section of actual metal samples. The polyhedrons investigated were the rhombic and pentagonal dodecahedrons and the orthic tetrakaidecahedron. However, the frequency distributions of the number of sides of plane intersections were not sufficiently characteristic to decide which polyhedron most closely approximated the average grain in a metal. Determination of Statistical Shape of Grain in Space Scheil3 was interested in the problem of calculating the distribution of grain sizes in space from the easily measured distribution of grain section sizes on the plane of polish. Assuming that the grains were spheres and using the plane distribution curve for a sphere shown in Fig. 1, he employed a successive subtraction method to calculate the spatial distribution. In order to evaluate the accuracy of these calculations, Scheil and Wurst4 determined the actual distribution of grain sizes in space in their sample of ingot iron by polishing off successive layers and following every individual grain in a series of micrographs. From curves of mean radius of intersection of a given grain vs thickness of metal removed in polishing, Scheil and Wurst attempted to derive the statistical shape of a grain in space. Their calculated plane distribution curve for this shape is compared with the distribution curve for a sphere in Fig. 1. A table of values based on this curve was prepared for calculating spatial distributions of grains. The calculated and measured spatial distributions of their sample then agreed much better than when a spherical shape had been assumed. In the present paper, an attempt has been made to learn something about the average metal grain by studying in detail the effect of the shape of regular polyhedrons on the plane distribution of areas and shapes of areas produced by random sections through them. From the data presented below, it can be concluded that the plane distribution curve for the average metal grain differs in three fundamental respects from the curve derived by Scheil and Wurst. Polyhedrons Selected for Study The polyhedrons selected for the statistical study are illustrated in Fig. 2 and consisted of a cube, a figure formed by cutting off the corners of a cube at the midpoints of the original edges, a tetrakaidecahedron, and a pentagonal dodecahedron. The length of edge on any one figure is a constant. For the above models the edge lengths were 3.50, 4.00, 2.00, and 2.08 in., respectively. A cube was selected for one of the polyhedrons because of its simple geometry, because it is a form that by repetition can completely fill space, and because it represents a convenient degree of departure from compactness beyond which the shape of

Jan 1, 1954

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

By R. W. Mancantelli, J. R. Woodward

IN 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company&apos;s Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1,1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia, and an ore dressing group at the company&apos;s Port Hope refinery. Pilot plant operations were conducted at the Ottawa plant of Sherritt Gordon Mines Ltd. under the general direction of C. S. Parsons, consultant on metallurgy and ore dressing for Eldorado. In mid-September, having compared results of the several research programs, Dr. Parsons recommended a process employing a carbonate or basic leach. He reported that, while the chemistry of the process had been proved, engineering of the flowsheet was incomplete, and he suggested that under normal conditions further pilot plant work at the Ace mine might be profitable. However, since this would involve a delay of 12 to 18 months in bringing the property into operation, he recommended that design of the concentrator proceed immediately. Concentrator capacity was determined by two considerations: 1) the amount of ore then available and 2) the expectation that continued improvements would be made in the ore dressing process as a result of the intensive research being carried out by the Mines Branch of the Department of Mines and Technical Surveys. As these improvements could affect both the chemistry and the en-

Jan 1, 1956

The Western World&apos;s gold reserves now exceed 23,000 mt (750 million oz), 65% of which exist in South Africa. Although several major mines are reducing production or closing because of depletion of reserves, new mines or expansions of existing mines are coming on-stream which will maintain an annual production of 684 mt (22 million oz) of gold well into the 1990s. These new operations by the South African mining industry represent the largest expansion since the opening of the Witwatersrand gold fields in 1886. Included in three new mines being opened is that of Anglo American Corporation&apos;s Elandsrand plant, their fir& new gold venture in South Africa in seventeen years. Current average grade of South African mines is 8.2 g Au per mt (0.24 oz per st); and while the cost of the Elandsrand 135,000 mt (149,000 st) operation, including mine development, was about $314 million, it is estimated that the cost of a comparable operation started today and completed in the mid-1980s would be of the order of $480 million. New mines to exploit low-grade ore bodies are, therefore, likely to be few in number, and further expansion will undoubtedly be in the form of extensions to existkg operations where cash flow can be used to finance development. The authors&apos; first monograph, "Gold and Silver Cyanidation Plant Practice," devoted a section to South African cyanide plant operation; and it is believed that this new volume would not be complete without a description of Elandsrand, South Africa&apos;s newest gold plant. The Elandsrand mine is adjacent to Anglo American&apos;s Western Deep Levels on the Far West Rand. The decision to go ahead with the development was taken in mid-1974 from the results of exploration drilling carried out over a period of .lo years. Results of 17 bore holes and 68 intersections of the Ventersdorp Contact Reef had indicated a gold-.bearing reef less than one meter thick at a depth of 1,800 to 3,000 meters (5,900 to 9,840 ft). Preliminary studies indicated a mine of 900 km (560 miles) of underground workings would yield 725,000 kg (23. 3 million oz) of gold from 60 million mt (66 million st) of ore to be milled over a period of 34 years. Eventually, when the mine is in full production, the total hoisting capacity will be 300,000 mt per month (331,000 st) for a milling capacity of 225,000 mt per month (248,000 st). The Elandsrand surface facilities have been built on a low range of 0 hills to take maximum advantage of the 10 slope in transporting ore

Jan 1, 1981

By S. Fisher Morris

THE New River coal-field embraces that portion of the Appalachian coal formation which lies on the waters of the New River, principally in Fayette and Raleigh counties, West Virginia, covering a strip of territory about forty miles in length along the line of the Chesapeake and Ohio Railroad from Quinnimont to Kanawha Falls, where the New River empties into the Kanawha, the railroad following the banks of the river the whole distance. (See map.) Between Kanawha Falls and the Valley of the Ohio lies the great Kanawha region, and these two coal-fields possess a greater variety of coal than can be found in any other portion of the country, enabling them to furnish the best fuels for any of the various demands of manufacture or domestic use, the Kanawha region possessing many varieties of gas, hard splint, and cannel coal, and the New River region bituminous and semi-bituminous, steam and coking coal. The New River, in its westward course towards the Kanawha, has cut its way entirely through the Seral conglomerate or No. XII of the Pennsylvania Reports, the Umbral red shales of No. XI appearing at the foot of the mountains at the eastern end of the region at Quinnimont, one of the upper ledges of the Conglomerate forming the summits; while at the western end, at Kanawha Falls, the top of the Conglomerate is nearly down to the level of the river, a portion of the " Lower Productive Measures" forming the greater portion of the mountains. These mountains rise abruptly from the banks of the river to a height of from 800 to 1200 feet, leaving only here and there narrow strips of bottom land, a few acres in extent; and as the measures consist principally of hard sandstones, shales, and conglomerates lying in a nearly horizontal position, the mountain-sides are very precipitous, with many long and high cliffs, which, with the great height of the mountains, give the country a very rugged appearance. Along the sides of these mountains fronting on the New River and its many tributaries there are exposed the outcroppings of several veins of bituminous and, semi-bituminous coal, varying in thickness from a few inches to over four feet, five of them being workable, or

Jan 1, 1880

By Porter W. Shimer

As is well known, cast-iron borings are a mixture of small particles of iron with more or less of finely divided graphite, separated from thc surfaces of these small particles during the process of boring. The amount of graphite thus mechanically mixed is, in all cases, quite large enough to cause serious difficulty when the problem is to obtain an average sample of a given lot of borings for carbon determination. This difficulty arises from the necessity of obtaining a uniform mixture of the heavy and comparatively coarse borings with the finely divided and light graphite, and of removing a sample for analysis without disturbing the uniformity of this mixture. It was first sought to overcome this difficulty by having the horings made very fine, so that they might have more nearly the size of the particles of graphite. It was not practicable, however, to secure this uniformity of size, since much of the graphite is in the form of the finest dust. At all events, the duplicate determinations of rarbon in these fine borings, made with every precaution by combustion in oxygen, frequently showed differences too large to be accounted for in arty other way than by imperfect sampling. Very coarse borings were also tried with the idea that the graphite separated from these large and heavy pieces would perhaps be inappreciable ; but it was found that quite enough was separated to vitiate the results. Various methods of mixing were tried, both in the bottle and on glazed paper ; but in all these mixtures it mas found that duplicate samples seldom colitained the same proportion of the mechanically mixed graphite; and when they did, there could be no certainty that it was the true proportion. All this was shown many times over by the failure of duplicates to agree closely, the differencheing sometimes so much as 0.20 per cent. It was finally clear that nothing was to be hoped from these methods. Even if we could secure a perfect mixture containing in every part its due proportion of graphite, it would run a great risk of being destroyed the moment a spatula was inserted to remove a sample: for the least agitation causes some of the graphite to fall through between the coarser borings.

Jan 1, 1886

By R. H. Sweetser

The Committee on Evaluation of Coal for Blast-furnace Coke reports progress in the working out of the problem of evaluation. There has been no full meeting of the Committee but there have been several conferences with two or more of the members present, and the different members have expressed themselves freely on the five points that have been under consideration since the meeting of the Committee in New York on Feb. 16, 1932. The need of a method of coal evaluation, not only of coking coals but all other kinds, is obvious. Under NRA it becomes imperative that coals of the same size from the same seam be priced according to their variations in quality, especially in reference to cleanliness in respect to freedom from extraneous ash-forming materials. In looking over the correspondence that has passed between members of our Committee, it is evident that much of the confusion and misunderstanding would disappear if we could realize that practically all of the variations in value of coal from the same seam of coal are due to variations in the amounts of extraneous materials that are contained in the coal as it passes over the scales for shipment. It is not now a question with our committee as to the differentials in value, or in prices, between different kinds of coking coals or between noncoking and coking coals; our present problem is to arrive at the method for determining the scale of values of the coal from a certain coal seam according to the increase or decrease of extraneous ash and moisture from a predetermined base line adopted for that particular coal. The five points mentioned above are the same as discussed at the meeting in February, 1932, except that the temperature for determining the moisture content has been changed from 212" F. to 221" F., at the suggestion of Dr. A. C. Fieldner. The points are: 1. It is proposed that the coal industry adopt as a base line for evaluating all coals the analysis of the coal as it passes over the neighing device that determines the tonnage of coal bought and sold. 2. It is proposed that the Committee on Evaluation of Coal for Blast-furnace Coke approve the adoption of the base line for Pittsburgh seam coal presented by F. A. Jordan at the annual meeting of A.I.M.E.

Jan 1, 1934

By C. W. Hazelett

This paper is a resume of some of the accomplishments in direct rolling of strip from molten metal, and a description of some experimental developments in recent years. In all the early developmental work, we used a pair of rolls with a bath of metal between them, maintained by flanges or plates at the ends of the rolls. These flanges produced an excess cooling of the metal and built up enormous pressures at this point as the metal went through the bight of the rolls. Many means were tried for compensating for this excess cooling, such as thickening the strip at the edges, heating the end dams directly or by flowing more of the molten metal against them, leaving an open crotch below the end dam and above the bight of the roll, where the excessive pressures built up could be relieved by some of the metal squeezing out at this point, and so forth. All of these helped somewhat to solve the problem, so that very large heats of many metals melting up to 200°F., having commercially uniform gauges, could be rolled up to 24 in. in width. The rolls were made by mounting heavy rings on heavy shafts, and pressures up to 75,000 lb. per inch in width were used. Cooling of the rolls was generally done by spraying water on the outside surface of the rolls that came in contact with the molten metal. Roll life was commercial with brass, barely satisfactory with copper, and totally impractical with steels. The greatest difficulty encountered in all this work was caused by lack of uniformity in the product, owing to a folding action in the mill. Those who are familiar with the operation of a rolling mill know that a bar entering a mill moves at a lower speed than the peripheral speed of the roll. However, the metal solidifying from a bath in a direct rolling mill is cast at exactly the peripheral speed of the roll. This results in irregular folding of the metal, some irregular remelting of the previously solidified sections, and it is difficult, if not impossible, in some cases to exert enough pressure to weld these folded sections sufficiently into a sound product. In addition to this melange of solid, semisolid and liquid metal in the bath, we know that pressure near the freezing point of any alloy in which the constituents have different melting points—and I believe all of them have—causes the lower-melling-point constituent to be squeezed back until it becomes cold enough to solidify and go through the mill. This segregates all alloys, the segregation increasing with the pressures and the freezing ranges of the metals. Add to these problems the excessive roll-maintenance costs with high-melting-point metals and then, the greatest difficulty of all, the vanity of homo sapiens where a matter of possibly large importance is being considered, and the problems seemed almost insuperable. It was long ago obvious to me that something much more than the size of a corporation&apos;s money and self-assuradce was necessary if this process was to be made commercial. I should like to show you first the performance of the only mill we ever really designed and built, to see what might be done with a well constructed mill. We accomplished something new in history with this prccess, first, by producing at Scovill Manufacturing Co. coils of brass

Jan 1, 1945

The research project on size reduction, sponsored by the mining industry through financial support from individual companies, is now embarking on a second three-year program. The first 3-year program had as its objectives assimilation of the literature on comminution and development of simulation programs encompassing the basic mechanisms of grinding. This involved investigating conditions under which a particle in a mill is captured, the stress to which it is subjected, its break probability, and the resulting particle size distributions. The results were used to obtain the most representative simulation models based on current knowledge of mechanisms. As part of this work a set of computer programs has been developed for the following cases: . Batch mill, by numerical integration for completely general selection and breakage functions. . Continuous open-circuit mill by same method as above. . Continuous open-circuit mill by general numerical integration method, including transient behavior

Jan 1, 1969

By S. Jess Larsen

Modern technology has provided the world with many innovations to improve living standards, ease of job performance, efficiency, and managerial control. While not expected to compete with the computer revolution, Kerr-McGee Coal Corporation has found a way using laser technology to solve one of their haulage problems. Operating successful and profitable surface coal mine facilities in Wyoming&apos;s Powder River Basin require economies of scale, flexibility of operation, conscientious cost control, and ever-present innovative effort. Because haulage costs are the major source of expenditure in surface mining, Kerr-McGee recognized early the need for maximum haulage productivity and the economies of scale provided by large haulage trucks. Special conditions that exist in the Powder River Basin coal fields require consideration. The coal thickness (up to 100 feet and more) and varying depths of overburden dictate that a haulage unit with good gradability characteristics be used to avoid undesirable long ramps. Two and often three coal seams are encountered by most mines, which necessitates operating from several coal and parting faces simultaneously. This situation consumes much space, and to minimize the scope of problems, a coal haulage unit with good maneuverability and stability is needed. Finally, the low density of coal (±1500 pounds/loose cubic yard) demands a large volume capacity to utilize truck load carrying capability effectively. These conditions prompted Kerr-McGee to select unitized two-axle bottom dump trucks of the 160-170 ton size for primary coal haulage at its two Gillette-area mines. Use of 170-ton bottom dump trucks at the Clovis Point Mine handles most of the coal haulage, but the truck

Jan 1, 1983

L. C. GRATON, Cambridge, Mass.-I should like to ask the authors if they attempted to draw any analogies with the manganese deposits at Franklin Furnace, N. J., and whether there are. any traces of zinc in these Brazilian-deposits. J. T. SINGEWALD, JR.-We did not think of them at all as analogous to the Franklin Furnace deposits and there is no appreciable percentage of zinc present. If these ores do contain zinc it could be there &apos;only as a fraction of a per cent. F. LYNWOOD GARRISON, Philadelphia, Pa. (communication to the Secretary *).-There is no disputing the fact that the manganese ore ,supply situation in this country demands serious consideration and is a matter of fundamental public concern. We are consuming this material at a steadily accelerating rate and there is no hope for a proportionate increase in the domestic supply. In the year 1916, this country imported 560,000 tons and produced only 27,000 tons from our own territory In 1915, the local production was 9,709 tons, which on its face shows the American output to have tripled during the past year. Those of us who are familiar with the

Jan 4, 1917

On Jan. 1, the office of the. National Service Committee was established at 502 McLachlen Building, Washington, D. C. The first work was to review current legislative information; which is being continued and good results are accomplished. Whenever matters of importance appear in the Congressional Record, notice thereof with such documents as are germane are forwarded to the members of the committee for their information and advice. The first formal report of the chairman was on the so-called Smith-Howard bill to secure Federal endowment for the establishment of engineering research. The chairman of the Committee, at the request of the Executive Committee of the Engineering Council, appeared before the Senate Committee on Education and Labor for the purpose of opposing those features of the so-called Kenyon bill which would create a practically permanent commission dominated by the Engineering Corps of the Army over all Federal engineering projects as well as state and municipal projects receiving Federal aid. The greater part of the time has been expended in correspondence and consultation on the matter of the establishment of a Department of Public Works. The results of this work lead to the belief that there is much promise of the establishing of such a department by the 66th Congress Hall members of engineering societies, as well as the societies themselves, will unanimously agree on and support a measure, and in order to secure such unanimous support, it will be advisable to call a conference of engineering societies. .

Jan 4, 1919

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study con firm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity.

Jan 7, 1950

By H. T. Byck

The plastering properties of six representative California drilling muds were studied over a temperature range of 70 to 175 F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water—the flowing medium—at elevated temperatures. It is concluded that no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds. Importance of Plastering Properties A survey of the literature on rotary drilling muds clearly shows the growing realization of the importance of plastering properties,&apos;-5 not only from the point of view of the successful completion of the mechanical operation of drilling the well but also from the point of view of minimum impairment of the natural flow possibilities of a given well. Poor plastering properties with attendant high filtration rate (large water loss to the formation) and thick mud sheath, lead to stuck drill

Jan 1, 1940

By H. T. Byck

The plastering properties of six representative California drilling muds were studied over a temperature range of 70 to 175 F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water—the flowing medium—at elevated temperatures. It is concluded that no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds. Importance of Plastering Properties A survey of the literature on rotary drilling muds clearly shows the growing realization of the importance of plastering properties,&apos;-5 not only from the point of view of the successful completion of the mechanical operation of drilling the well but also from the point of view of minimum impairment of the natural flow possibilities of a given well. Poor plastering properties with attendant high filtration rate (large water loss to the formation) and thick mud sheath, lead to stuck drill

Jan 1, 1940

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By Irwin R. Higgins

CONTENTS A. Introduction B. System Description C. Uranium Pilot Plant Programs D. Summary INTRODUCTION The Chem-Seps Continuous Countercurrent Ion Exchange (CCIX) contactor was first conceived of in 1951 at the Oak Ridge National Laboratory. In the 27 years that have passed, there has been a steady stream of pilot plant process development studies on a variety of processes far too numerous to mention. These have been in the area of water and waste treatment, chemical processing, ore leach treatment, and many others. Many successful production systems have been installed and operated in a variety of applications. A few of these are described herein together with a description of the system and its operational characteristics. SYSTEM DESCRIPTION Chem-Seps Continuous Countercurrent Ion Exchange* is a single loop in which various sections are separated by valves to isolate the sections performing different functions simultaneously. (Refer to Figure 1). To explain the working of a typical unit, let us use a simple configuration used in water softening or demineralization. The resin is moved in small increments by the hydraulic ram action. All solution flows are countercurrent to the flow of resin. The contaminants are removed in the process cycle and the resin is moved in the pulse cycle. A controller in the effluent stream from the treatment section senses the proper limit permissible in the effluent. In the process cycle, the influent enters through a set of distributors, moves downward and leaves through a set of collectors. Simultaneously the regenerant enters through valve RE and leaves through valve WA. The rinse enters through valve RI and its duration is controlled by an interface controller. In the process cycle, valves B, C, and D are closed, isolating all the sections. The duration of the process cycle is 4-10 minutes depending on the contaminants to be removed and is controlled either by a timer if the contaminants are fixed, or a controller in the effluent stream, if the contaminants fluctuate at short intervals. Valve A is open and resin is dropped to the pulse section simultaneously with the removal of contaminants in the treatment section, regeneration of loaded resin in the strip section, and rinsing of regenerated resin in the rinse section. As the resin drops through the valve A, it is backwashed to remove the suspended solids or resin fines. Removal of these fine particles is important to avoid the unnecessary pressure drop in the bed and plugging of the distributors. At the end of process cycle, all flows going into the unit and out of unit are automatically shut off. The valve A closes and valves B, C, and D open in proper sequence. A slug of water enters through valve PU, a predetermined incremental volume of resin moves into the regeneration section, an equal volume of regenerated and rinsed resin enters the bottom of the treatment section, and an equal volume of the loaded resin leaves the top of the treatment section and goes into the resin reservoir section. (The resin movement is plug flow with the Reynold&apos;s number being in the laminar region of the curve, and no fluidization occurs during the pulse cycle.) The total time required for proper sequencing of valves and the movement of resin is 20-30 seconds. At the end of this period, the valves B, C, and D close and valve A opens. The solution valves open and normal steady state operation begins. All valves are interlocked and properly sequenced. The resin movement is precisely controlled by sonic devices. Special Features of Chem-Seps CIIX "Downflow"*: The raw feed in the treatment section moves downward and the resin moves upward in the treatment section. The "downflow" of feed overcomes the handicap encountered in "upflow" systems. The "upflow" of feed requires a certain minimum flux during process cycle to lift the bed and keep it

Jan 1, 1979

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942