Search Documents

By John D. Clark

ONE'S lifetime does not usually offer the opportunity to observe and be a part of the commercial development of an entirely new material. Petalite has been known for over a century, but at first it was presumed rare. However, it was found to be so abundant that it has become a new and extremely useful industrial tool.

Jan 10, 1950

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By Alfred F. Brainerd

A few months since, Prof. Lawrence C. Johnson, of the U. 8. Survey, discovered in Mississippi large deposits of carbonate iron-ore, geologically located in the Claiborne formation of the Tertiary Epoch. These deposits are not pockets, but continuous layers or beds extending for miles, and can be located with certainty where they have not been removed by erosion. Upon examination, recently made by G. W. West, Birmingham, Ala., the largest deposits and highest grades of ore were found near Enterprise, Lauderdale county, and in Clark county, Miss. These beds measure from 10 to 18 feet in thickness, are superimposed upon a " burr rock," associated with green sand, and dip 30 feet to the mile southeast, at an altitude of 350 feet above sea-level, can be

Jan 1, 1888

By M. R. J. Wyllie

In a recent publication1 wetting phase relative permeability was exvressed as: and it was stated that a similar expression applied, mutatis mutandis, to non-wetting phase relative permeability; i.e., In Equations (1) and (2), Sw and S0 are respectively the wetting and non-wetting phase saturations as a fraction of the pore volume; PC is the capillary pressure; I; the wetting phase electrical resistivity index; IN, the analogous non-wetting

Jan 1, 1951

By M. R. J. Wyllie

In a recent publication1 wetting phase relative permeability was exvressed as: and it was stated that a similar expression applied, mutatis mutandis, to non-wetting phase relative permeability; i.e., In Equations (1) and (2), Sw and S0 are respectively the wetting and non-wetting phase saturations as a fraction of the pore volume; PC is the capillary pressure; I; the wetting phase electrical resistivity index; IN, the analogous non-wetting

Jan 1, 1951

By Olin G. Bell

The year 1934 in Southwest Texas was marked by aggressive development and exploratory work and resulted in the finding of five new fields and a new producing horizon in one of the older fields. This activity is the result of a reasonable market outlet for production, on both oil and gas, and the fact that drilling and operating costs are reasonable and that possibilities of finding new productive areas are rather high. A large part of the area is prospective and very little, if any, satisfactory surface geological work can be done. This, together with the possibility of finding new productive areas, stimulates wildcatting throughout the counties under discussion. Development work continued actively in all of the newer fields. Exploratory work was most intense in Duval, McMullen, Starr and Zapata counties. The activity in Duval and McMullen counties was the result of persistent efforts to find new trends of production similar to and perhaps associated with the Government Wells group of fields. The activity in Starr and Zapata counties was stimulated by the discovery of the Sam Fordyce field in Hidalgo County as well as the continued effort to find new productive trends southeastward from some of the older fields in northeastern Zapata County and western Jim Hogg Comity. Statistics on production are shown in Tables 1 and 2. New Fields Lopeno.—The Lopeno gas field in the southwestern part of Zapata County was opened in August, 1934, by R. B. Morrison No. 1 Ramirez. This is an anticlinal structure mapable in Claiborne beds and the producing horizon is the Queen City sand at 2100 ft. in the Upper Mt. Selman. At the close of the year only two gas wells had been completed but drilling operations were in progress on several other wells and a gas line was being laid to the field so that withdrawals from the area will begin early in 1935. Comilas.—The Comitas field was opened by Merle Gunby No. 1 Haynes in a sand at 800 ft. in an area southwest of the Escobas field. The discovery well had an initial production of only about 16 bbl. of oil

Jan 1, 1935

With over one year experience, Western Deep Levels Ltd., reports satisfactory operation with new features of its 200,000 ton per month gold reduction plant. Western Deep is Anglo American group's newest gold mine. It is situated 43 miles west of Johannesburg on the West Wits Line and will ultimately be extracting ore from a depth of 13,000 ft. Although the plant was put in production in March 1962, after a three month break-in period, construction of the fifth milling section was not completed until last month.

Jan 7, 1963

By Edgar Bain

IN STUDYING the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900° C. (1650°, F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement-the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1. shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 2, 1924

By Peter F. Howard

Major reserves of phosphorite were found in the Georgina Basin of northern Australia in the period 1966-1968. Geological investigations by various companies and the Bureau of Mineral Resources of Australia show that these phosphorite deposits are associated with siltstones, cherts, siliceous shales, and limestones of the Beetle Creek formation or its equivalents, all of lower Middle Cambrian age. The discoveries resulted from systematic Australia-wide exploration programs by several companies utilizing, in concept, the relation of basin stratigraphy, lithologic associations, tectonics, and phosphate occurrences to paleogeography in respect to its paleolatitude and areas of supposed oceanic upwelling. In terms of field techniques, the first discovery at Duchess, North Queensland, resulted from the recognition of a phosphorite interval at depth in a stratigraphic oil well followed by prospecting of the nearest outcrop of the equivalent aged rock succession. In Northern Territory, the Wonarah-Alexandria deposits, which do not crop out, were discovered by analysis and interpretation of gamma radiation logs followed by drilling.

Jan 1, 1972

By R. C. Ferguson, Harlowe Hardinge

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By Robert W. Zimmerman

POROUS SOLID COMPRESSIBILITIES There are four different compressibilities associated with porous solids, each relating the fractional change in either bulk volume or pore volume with the change in either pore pressure or confining pressure. These will be referred to as Cbc, Cbp, Cpc, and Cpp, with the first subscript denoting the relevant volume, and the second subscript denoting the relevant pressure. They are defined as: [ ] Note that minus signs are included in two of the definitions so that each of the compressibilities will always have a positive value. In general, each compressibility depends on the elastic moduli of the matrix material, the porosity, and the exact geometry of the pores. Taking the latter factor into account calls for separate analysis for each different pore shape, which of course can only be attempted for a few relatively simple cases. But lower bounds for each of the four compressibilities can be found, independant of pore structure, in terms of only the porosity (0) and the elastic moduli of the matrix material (any pair chosen from K, E, G and V). The first step is to find relationships between the four compressibilities, starting with the following observation: If a porous solid made of a linear elastic, isotropic and homogeneous matrix material is subjected to uniform hydrostatic pressure of magnitude P on its external and all of its internal (pore) surfaces, the state of stress in the solid will be exactly the same as that which would occur

Jan 1, 1982

By R. Neilson M. E. Clark

(with map on plate I.) THE coal-beds of Canyon City are situated six miles below the town, upon the Arkansas River. At this point the Rocky Mountains have thrown out from their main ridge two spurs. The one to the north, containing Pike's Peak and Cheyenne Mountain, is known as part of the "Rim Range;" the one to the west and south is known as the `1 Green¬horn Range." Against these syenitic mountains, the later rocks are piled and uplifted; at right angles to the direction of this main uplift is the axis of a lesser plication. On the north, west, and south, the pitch is steep, gradually flattening as it approaches the centre of the basin and rising again to the east at a pitch of about 5°, thus forming a perfect basin, the centre of which is only three miles east of the base of the Greenhorn Range.

Jan 1, 1873

By John McDonald

THE amount of published literature in the field of mechanical proper-ties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherch1 have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing' with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in, properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the proper-ties of alloys in conditions where the effect of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these proper-ties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments will produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of working and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treat-ments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloys have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are relatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1939

All the Technical PUBlications and Preprints published in 1932 are available at Institute headquarters. They are also on file in public, university and technical libraries and, when so indicated in the list, may be found in the Transactions. Copies of the Technical Publications have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Insti-tute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of Preprints may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. Metal Mining Technical Publi- Title Author Meeting Trans. cation Volume No. and Page* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 88. 95 F.52 Shaft. Butte. Montana (13) Feb.. 1932 487-A.46 Progress in the Improvement of Max H. Barber New York. Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932 Milling And Concentration 445-B.37 Soap Flotation of the Nomulfides Will H. Coghill New York. H.19 (18) J. Bruce Clemmer Feb., 1932 461-B.38 Principles of Flotation—An Experi- I. W. Wark New York. mental Study of the Effect of A. B. Cox Feb.. 1932 Xanthates on Contact Angles at Mineral Surfaces (48) Iron and Steel Division 447-C.81 Electrochemical Potentials of Nitri- Shun-ichi Satoh New York, fied Steels (31) Feb.. 1932 450-C.82 Reaistanoe of Iron-aluminum Alloya N. 9. Ziegler New York. 100, 267. 670 E.143 to Oxidation at High Tempera- Feb., 1932 tures (8) 451-C.83 Pressure Welding of Low-carbon C. H. Austin New York. Steela with Theoretical Con- W. S. Jeffries Feb.. 1932 siderations on the Mechanism of Such Welding (42) 453-C.84 Inclusions—Tbeir Effect, Solubility C.E.Sims New York, 100, 154, 176 and Control in Cast Steel (24) 0. A. Lillieqvist Feb., 1932

Jan 1, 1932

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

By J. A. Musselman, P. F. Gnirk

A study was made of indexed penetrations by a single dull bit tooth under statically applied loads into rock subjected to confining pressures from atmospheric to 5,000 p.si and atmospheric pore pressure. Experimental results obtained with a 45" wedge tooth over the above range of pressures are presented for two limestones and a sandstone, a variely of indexing distances and two degrees of tooth dullness. The optimum distance between successive bit-tooth penetrations required for maximum rock damage and chip formation decreases substantially with increa.sing confining pressure above the brittle-to-ductile transition pressure of a particular rock. However, the distance remains approximately constant for a variation in confining pressure below the transition pressure. At a given confining pressure, the bit-tooth force required lor chip formation is constant for indexing distances greater than optimum, but generally decreases linearly with decreasing indexing distance for distances less than optimum. The chip-formation force data obtained at confining pressures for which the chip-generation mechanism is macroscopic-ally of a pseudoplastic nature compare favorably with previous theoretical results for indexed dull hit-tooth penetrntion into an idealized, rigid, perfectly plastic rock. INTRODUCTION To study the cutting action of a roller-cone bit, the interaction of a penetrating bit tooth with craters formed in a rock surfacc by the passage of previous bit teeth must be considered. Current knowledge of the basic mechanics of bit tooth-rock intcract:on under simulated borehole environmental conditions has been extensively reviewed.',' Particularly of current interest are the effects of bit-tooth shape, distance between successive penetrations and differential pressure at the rock surface on the extent of the interaction. Pertinent to this paper are results of an experimental investigationb f the interaction between successive penetrations by sharp, wedge-shaped bit teeth. It was demonstrated that both bit-tooth angle and differential pressure influence the extent of rock damage between successive bit-tooth penetrations. Specifically, the optimum or minimum distance between successive penetrations required for maximum interact'on or chip generation tends to decrease with decreasing bit-tooth angle and increasing differential pressure. In addition, at differential pressures on the order of 2,000 psi for four va- rieties of limestones and sandstones, the macroscopic mechanism of chip formation exhibits a transition from brittle to ductile. In this paper, experimental consideration is given to successive or indexed penetrat ons by wedge-shaped bit teeth. Since pore pressure in a rock sample is maintained at atmospheric pressure, the differential pressure at the fluid-rock interface is equal to the confining pressure. The degrees of bit-tooth dullness include teeth with flat and round apexes (Fig. 1). Of primary concern in this paper are the bit-tooth forces required for chip formation, the macroscopic mechanism of chip formation and the minimum distance between successive penetrations, i.e., optimum indexing distance required for maximum rock damage, as functions of differential pressure. Of further interest is a comparison of actual bit-tooth chip formation forces at elevated differential pressures with calculated forces from previous theoretical results4 for indexed dull bit tooth penetration into a rigid-plastic rock. EXPERIMENTAL APPARATUS AND PROCEDURE The experimental apparatus consists of a pressure vessel equipped with a piston through the side of the vessel (Fig. 2). A single bit tooth inserted in the lower end of the piston is forced at a desired rate into the rock when the ram pressure chamber is pressurized. Electrical instrumentation incorporated into the apparatus yields a graphical plot of force on the piston as a function of bit-tooth penetration or displacement into the rock. Since the piston and ram assembly are in force equilibrium for a constant confining pressure in the main vessel, the fluid volume in the vessel remains constant during bit-tooth penetration. Hence, the force resisting penetration of the tooth is independent of the force exerted on either end of the as-

By W. W. Mein

IN March 1949 the Calaveras Cement Co. was sued by five landowners whose properties are located in the vicinity of the plant. These landowners—all of them cattle ranchers—sued for dust damages of $120,338 and for an injunction preventing the company from casting dust upon their properties in injurious quantities. The issue was split, the jury deciding the amount of damages and the court handling the injunction features. The action came to trial before a jury in April of that year and resulted in damages being awarded in the amount of $7,508. A month later the court issued its injunction requiring recovery of stack dust to an 87 pct minimum. The Calaveras plant, shown in Fig. 1, is located three miles from San Andreas in the heart of the Mother Lode country, about 45 miles east of Stockton, Calif. Since it is in a small town, the company's responsibilities to its employees and to the community are different from those of plants located in large centers of population. Construction of the plant was begun in 1925, and production was started the following year. Standard gray Portland cement as well as several specialty cements are produced. Production facilities have been continually enlarged so that the present capacity is more than double what it was 25 years, ago. The most important item in the company's expansion program was the purchase in 1945 of an 11 ft 3 in. x 360 ft Allis-Chalmers kiln which had been declared surplus by the Defense Plant Corp. The company is now able to produce about 2,500,000 bbl of cement a year, and employment at the plant is approximately 300. The production of cement has always involved a dust problem, solution of which has been attempted in a number of different ways. By far the most efficient method of catching dust discharge is electric precipitation. Soon after the company went into production in the 1920's, the landowners near the plant began complaining about dust discharge. The company settled the matter by paying them a total of $27,000 for dust damages incurred during the period from 1929 to 1938. In the latter year the two-unit Cot-trell Electric Precipitator shown in Fig. 2 was installed and collected over 85 pct of the dust resulting from operation of the two 11 ft 3 in. x 10 ft x 240 in. kilns. From 1938 until 1946 the landowners registered no objection and were apparently satisfied with that dust recovery. In 1946, however, the substantially higher production resulting from operation of the new kiln immediately overtaxed the facilities of the existing two-unit precipitator. In a short time claims for dust damages were again received from the landowners. The company informed them that because of postwar shortages it would take several years to install a new precipitator. The company stated that it intended to purchase an additional precipitator and offered in the meanwhile to pay the landowners a fair amount to cover their damages. This offer was rejected and the landowners filed suit in the Superior Court of Calaveras County asking for total damages of $120,-338 and for the injunction outlined above. Case for the Ranchers The attorneys for the plaintiffs produced three different types of witnesses: first, the landowners themselves and members of their families; second, other cattle raisers who were sympathetic to the plaintiffs; and third, several types of technical experts: veterinarians, soil chemists, and an aerial photographer. The testimony of these witnesses was designed to establish that the flue dust from the plant had not only damaged the land and the forage, but had also caused fluorine poisoning to their animals. By a combination of these causes, the plaintiffs attempted to prove substantial loss of profits.

Jan 1, 1952

By Strathmore R. B. Cooke

On the basis of experiments conducted on quartz using a bubble pick-up method, it was shown in an earlier paper1 that this mineral will preferentially adsorb hydrogen, calcium, or sodium ions, depending on the relative concentrations of those ions in the solution in which the quartz is immersed. For quartz particles ranging in size from 0.2 to 1 mm, it was demonstrated that the concentration of calcium in solution (assumed present as ions) necessary to completely activate quartz for flotation is given by the expression: Ca++ = [H+] X 106 + [Na+] X 10-3 In this expression, ionic concentrations are in mols per liter. It was further shown that the pick-up method is apparently more sensitive to changes in reagent concentration than the standard captive-bubble method, and that induction times are apparently much reduced. Since completing these earlier tests, a new type of cell has been constructed; this is shown in Fig 1 and 2. In Fig 1, A is a ground joint, B is a central tube reaching to within a few millimeters of the bottom of the cell, and C is a stopper which may be removed for reagent addition, and serves the further purpose of excluding carbon dioxide from the air during the test. The entire cell is constructed of Pyrex glass, and does not give the trouble experienced with the earlier cell, in which activating ions were released from the glass at high pH values. The only critical factor in the construction of the cell is the clearance between the central tube and the bottom of the cell. This clearance should be sufficiently small that the bubble can be pressed directly on the mineral grains lying on the bottom of the cell. In the pick-up tests to be described in this paper, the reagents used were all of C. P. grade, except the sodium oleate, which was Merck's "neutral powder." The quartz employed was water-clear vein quartz, sized on screens, cleaned with both hydrochloric acid and sodium hydroxide, and given a thorough final washing with distilled water. Experimental procedures were the same as described in the earlier paper. EFFECT OF SIZE OF QUARTZ ON PICK-UP To ascertain the effect of particle size on the adsorption of calcium ions, the quartz was sized from minus 14 plus 20 mesh through the intervening screen sizes to minus 270 mesh plus 400 mesh. Each size was thoroughly cleaned, and then tested in the cell at different calcium chloride and sodium hydroxide concentrations, and at a constant sodium oleate concentration of 20 mg per liter. All particles, within the size range given, exhibited complete pick-up within the curve expressed by the equation above. This presumably means, when the conditions imposed by the equation are satisfied, that this maximum is independent of particle size. However, it was found that the range through which partial particle pick-up occurred progressively broadened as particle size decreased. This is shown in Fig 3, in which curves B, C, and D show the limits at which pick-up just commences (as the pH is increased) for particles of minus 14 plus 28 mesh, minus 65 plus 100 mesh, and minus 270 plus 400 mesh size, respectively. These results indicate that for satisfactory activation, at any given pH, a lower calcium ion concentration is required for fine particles than for coarse particles. EFFECT OF HIGH ALKALINITY ON PICK-UP At calcium concentrations of between 1 and 10 mg per liter, and at high alka-linities, it was noticed that pick-up ceased as soon as calcium hydroxide commenced to precipitate. This effect was investigated at other calcium concentrations, with the same results. Solutions of calcium chloride, containing 105, 104, l03, and l02 mg of calcium per liter were made alkaline with sodium hydroxide until calcium hydroxide just started to precipitate, according to the following equation: CaCl² + NaOH -+ Ca(OH)2 + 2NaCl The beginning of precipitation was taken as that point at which either a faint opalescence appeared in the solution, or a Tyndall cone became ap-

Jan 1, 1950