Search Documents

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

May 219t, 1872. THE Institute assembled in the rooms of the Geographical Society at the Cooper Union, Tuesday evening at 8 P.M. President Raymond called the meeting to order, and introduced Mr. Abram S. Hewitt, who welcomed the Institute to New York. President Raymond, in behalf of the Institute, replied. The President then read the following report of the Council for the past year. The Council respectfully report that the American Institute of Mining Engineers has held four meetings-at Wilkes-Barre, Bethlehem, Troy, and Philadelphia, respectively-all of which have been well attended, and socially and professionally most successful. The proceedings of these meetings having been published in the Engineering and Mining Journal, and sent to all members and associates, are sufficiently well known. Forty-four papers, by twenty-six authors, have been read. These papers embrace s wide range of subjects, and prove the practical character of the proceedings of the Institute. The finances are in a satisfactory condition. By the report of the Treasurer it appears that $1290.10 have been received, $519.90 expended, and that $770.20 now remains in the treasury exclusive of fees for 1872. This fund, it is hoped, will be so increased by voluntary subscriptions as to enable us before long to issue s volume of our most important transactions in a permanent form. The Council has made a favorable arrangement with the Scientific Publishing Company, publishing the Engineering and Mining Journal, by which that journal became the organ of the Institute for the first publication of the proceedings, papers, and notices to members. This arrangement it is proposed to continue through the present year unless the Institute shall otherwise direct. It is not intended to supersede the publication of an annual or occasional volume, but to maintain an interest in the Institute, and to serve the convenience of members while our funds do not permit s more ambitious publication.

Jan 1, 1873

By S. D. Dahlgren

ORDERED G.P. zones having the cesium chloride structure were found to exist in the bcc iron-rich grains of an Fe-Au-Cu alloy that had been supersaturated with approximately equal atomic percentages of gold and copper, and aged at 400° and 350°C. Streaks and superlattice spots in electron diffraction patterns revealed the presence of the ordered zones in the aged material. The ordered Ll2 structure is commonly found for precipitates in fcc metals (e.g., Ni3A1 in nickelL7&apos;) but it is uncommon to find precipitates in bcc metals having the cesium chloride structure. The formation of the G.P. zones caused age hardening of the grains. Samples containing 3.8 at. pct each of gold and copper (with the remainder being iron) were annealed at 95@ or 1125°C in quartz capsules and were quenched by breaking the capsules under water. X-ray diffraction patterns revealed two solid solutions in the quenched samples. One solid solution was bcc and the other was fcc. The microstructure consisted of iron-rich grains of 0.3 mm diam surrounded by a yellow gold-copper-rich grain boundary network. The Au-Cu phase diagram %hows continuous solid solubility of gold and copper with ordered phases forming below 410°C. None of the ordered Au-Cu phases have the cesium chloride structure. Both Fe-Au and Fe-Cu phase diagrams3 show extended miscibility gaps and only terminal solid-solution phases. Consequently, it is reasonably certain the iron-rich grains consisted of an a-phase terminal solid solution, and the grain boundary network consisted of a gold-copper-rich terminal solid solution. Lattice parameters of the quenched solid solutions were consistent with the suggestion that the quenched phases were terminal solutions. The lattice parameter of the bcc phase (2.879A) obtained upon quenching from 950°C was higher than that (2.866A) for pure iron. The fcc phase in this sample had a lower lattice parameter than that for a 50 at. pct Au and 50 at. pci Cu solid solution, i.e., 3.866 compared to 3.877A. The lattice parameter for the 50 pct Au and 50 pct Cu solid solution was interpolated from data for Cu-Au solid solutions.4 More gold and copper were soluble in iron at 1125°C than at 950°C as indicated by a 0.012A increase in the bcc lattice parameter for a sample quenched from 1125°C. After the alloy had been quenched from 950° and 1125°C, the bcc lattice parameters were 2.879 and 2.891A1 respectively G.P. zones having the cesium chloride structure-which formed during low-temperature aging—were detected by electron diffraction and observed with electron transmission microscopy. In Fig. 1, the asymmetrical streaks parallel to ( 100) directions indicate that platelike G.P. zones had formed parallel to (100) planes of the matrix. The direction of streak asymmetry shows that the bcc unit cell of the G.P. zones was larger than the bcc cell of the matrix. The ordered cesium chloride structure is indicated by low-intensity superlattice spots at 010 positions which are nonallowed for bcc structures. The superlattice spots are streaked; therefore they are from the G.P. zones and are not caused by rel-rod effects of a thin matrix phase. The appearance and size of the zones observed in electron transmission microscopy and the appearance of the asymmetrical streaks in the electron diffraction patterns for the Fe-Au-Cu alloy were the same as those observed for a similarly treated Fe-Au alloy.&apos; Ordered G.P. zones were detected also for an Fe-Au-Cu sample aged only at 400°C. The production of the ordered cesium chloride structure zones by low-temperature aging of super-

Jan 1, 1968

By Willard P. Ward

IT is the object of the present paper to bring to the notice of members of this Institute, the results of experiments made during the past six months in the manufacture of the alloys of iron and manganese in the blast-furnace. The ores at hand and available for the purpose were brown hematites, containing but a very small percentage of manganese, and various manganese ores containing a small percentage of iron. It is hardly necessary here to call attention to the statements regarding the production of iron-manganese alloys from such ores, which are given by all the well-recognized authorities on metallurgy. Suffice it to say, in a few words, that they hold that the operation is practically impossible, and that in the use of oxides of iron and manganese, mechanically intermixed in the same ore, much difficulty has been found in producing spiegeleisen. Spathic ores, containing manganese chemically combined, are alone recommended for the production of spiegel, and even then it is said that well-managed furnaces produce only about 75 to 80 per cent. of spiegel, the balance of the production being white laminated pig or gray iron.

Jan 1, 1876

By O. Skiredj, J. F. Elliott

It has been necessary to collate the available data on the solubility of graphite in Fe-Si-Mn alloys for a study of slag-metal equilibria in ferromanganese production. That study will be reported later; the collation is reported here. The carbon content of graphite-saturated liquid iron above 1153ºC by Chipman and co-workers1 is: %C= 1.34 + 2.54 x 10~3t(°C) [l] For graphite-saturated manganese above 1322ºC it is: %C = 2.68 + 3.52 x 1CT3 t(°C) [2]

Jan 1, 1963

By Charles M. Rolker

The mining industry of Colorado received a powerful impetus from the enterprising railroad builders who, rating highly—perhaps, in some instances, too highly,—the natural resources and favorable conditions of the State for the production of the precious metals and lead, covered it, in advance of any thorough general development of these resources, with a network of railroads. At that time, everything was viewed couleur de rose; population was gaining rapidly, and much more in the way of productivity was expected of certain districts than was subsequently realized. It is, therefore, not quite fair to judge of the wisdom of constructing some of the branches of the Colorado railroad system from the standpoint of later experience. With the building of railroads, a demand sprang up for iron and

Jan 1, 1886

By Dewitt T. Ring

Reliable and detailed data covering the enormous number of wells drilled and the long historical production of the state, many of which were never recorded until recent years, render it impossible to gather statistical material suitable for the Institute&apos;s standardized form. The total production of crude oil in Ohio for the year was 3,654,503 bbl., which is less than the total production in the United States for the peak day of August 1937. For a period of eight years, from 1895 to 1902 inclusive, Ohio produced more oil than any other state. During the year, 1271 tests were drilled in the state, or 114 more than in 1936. Of these, 317 were oil wells, with an initial production of 7088 bbl., an average of 22.3 bbl. per well; 503 were gas wells, with an initial open flow of approximately 222,441 M cu. ft., or 443 M cu. ft. per gas well drilled; 451 were dry holes, that is, 35 per cent of the total completions. A number of factors account for the steady decline of oil production in Ohio. In the state, at the close of thc year, there were fewer than 28,122 producing oil wells. In 1936, there were 30,150 operated oil wells with an average yearly production per well of 126 bbl. The production for 1937 averaged 130 bbl. per well. During the year, 2028 oil wells were abandoned. In other words, old wells are being abandoned more than six times faster than new ones are being drilled. Since the inception of the oil and gas industry in Ohio, between 150,000 and 160,000 wells have been drilled in the state; new potential territory, offering desirable locations for either oil or gas, is becoming increasingly more difficult to find; the dry-hole percentage will continue to increase. Prices Another factor directly affecting the crude situation during the year was the matter of price and proration of Pennsylvania grade oil. The posted price for Pennsylvania grade in Ohio on June 7 was $2.37 per barrel; at the close of the year, it was $1.70 per barrel, or a reduction of 28 per cent in price. In addition to this price cut, a 50 per cent pro-

Jan 1, 1938

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metaliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land the surface of which is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar " method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years .ago, has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are equally applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral, owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1927

By J. R. Barrett

Geotechnical techniques to evaluate conditions in underground metalliferous mines change through a mine&apos;s development from prefeasibility to remnant mining. The objectives of this paper are to determine the geotechnical requirements of typical underground metalliferous mining projects, to determine any shortfalls in conventional geotechnical techniques in satisfying these requirements, and to determine the costs of such investigations in proportion to the project expenditure. Finally, areas for future research and development are discussed. A group of over one hundred case history studies are examined to generate data on typical mining problems. The case studies include projects at most Australian underground metalliferous mining operations supplemented with case studies in Canada, Africa, Asia and Europe.

Jan 1, 1983

By Forrest W. Kinsey

The use of pellets in North American blast furnaces has made the mixes used in the associated sinter plants unique. These mixes generally contain a high percentage of fine waste oxide materials as the principal iron bearing portion of the mix, with iron ores and concentrates added in minor amounts only. Additionally, the sinter basicity is always above one and can be three or higher. This paper will discuss the large body of knowledge and experience developed by one company on this type of sinter mix. Results of laboratory tests will be used to illustrate how mix composition and feed preparation affect sinter productivity and quality.

Jan 1, 1977

By Allen R. Rowen

One of the greatest deterrents to more widespread use of manufactured lightweight aggregate is the fact that no industry-wide standards for its application exist. It is true that ASTM has specifications covering lightweight aggregate, but they are so broad as to be of little assistance in mix design work. Today even an engineer who has worked with one lightweight aggregate may be faced with re-education on his next light- weight concrete job if he is in an area served by another producer. Manufacture of lightweight aggregates has grown with the country, appearing in the patent literature at least as early as 1875, when a patent was issued covering use of burnt clay aggregate as an admixture in manufacture of artificial stone. The widely known Haydite came into the picture prior to 1920 as a result of work by Stephen J. Hayde, and there have been many others since who have contributed significantly to the growth of the industry and its technology.

Nov 1, 1956

By E. P. Miesch, P. B. Crawford

A study was made of the effect of permeable and impermeable lenses in a reservoir on the production capacity of a well. Both steady-state and unsteady-state data were obtained. An electrical resistivity model was used to obtain the steady-state data and thermal models. were constructed to obtain the unsteady-state data. The productivity of a well is affected very greatly only when the lenses are close to the well. The effect of circular lenses on the productivity ratio can be correlated with the distance from the center of the lens to the center of the well divided by the radius of the lens. When this dimensionless distance is equal to six or greater, the effect of the lenses on production capacity will be negligible. The pseudo steady-state productivity of a heterogeneous reservoir can be predicted using steady-state data. INTRODUCTION Many analytical solutions of reservoir behavior assume that reservoir rock is uniform and homogeneous. Although this assumption is used, all of the data from core analyses and well logging indicate that the reservoirs are heterogeneous. Very little work has been done on the performance of heterogeneous reservoirs. The work of Landrum,l et al. showed that transient phenomena in oil reservoirs could be studied with thermal models. Pickering and Cotman2 used thermal models to study flow in stratified reservoirs and investigated the effect of inhomo-geneities in oil reservoirs on transient flow performance. Loucks3 made a mathematical study of the pressure build-up in a system composed of two concentric regions of different permeability. Root, Silberberg and Pirson4 studied the effect of the growth of the flooded region on water influx predictions using a thermal model consisting of three concentric cylindrical regions of different thermal properties which simulated the aquifer, the flooded region and the unflooded portion of the original hydrocarbon region. Tomme, et a1.5 made a mathematical study of vertical fractures. The object of this investigation was to study the effect of highly permeable and impermeable lenses in the vicinity of the wellbore on the pressure depletion history of the well. Steady-state data were obtained for both conductive and nonconductive lenses that completely penetrated the formation. The lenses were symmetrically located at various distances from the wellbore. The unsteady-state data were obtained on seven thermal models. EXPERIMENTAL EQUIPMENT AND PROCEDURE STEADY-STATE DATA The steady-state data were obtained from an electrical resistivity model 30 in. in diameter and approximately 11/2 in. deep. The outside of the model was lined with a 30-in. diameter copper strip, which served as the outer boundary of the reservoir. The bottom was covered with a sheet of plexiglass so that it would be nonconductive. The model was filled with a slightly saline solution. The well size was varied from an 0.064-in. diameter copper wire to a 10-in. diameter copper cylinder. Readings were taken with an impedance bridge using AC current to prevent polarization at the contacts. Copper and wax lenses were used to represent infinitely conductive and nonconductive lenses, respectively. The resistance was first measured for each well diameter with no lenses in the reservoir. Then the conductive and nonconductive lenses were spaced symmetrically at various distances from the well and the resistance read from each lens location. The diameters of the conductive lenses were 3, 1.022 and 0.624 in., and those of the nonconductive lenses were 3, 2.25 and 1.563 in. The ratio of each resistance reading to the resistance reading with no lenses in the reservoir

Jan 1, 1965

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.&apos;l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1&apos; to ensure axial application of the load. The rate

Jan 1, 1942

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.&apos;l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1&apos; to ensure axial application of the load. The rate

Jan 1, 1942

By Robert T. Walker

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)-Mr. Kinkel&apos;s article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel&apos;s conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel&apos;s nomenclature being used

Mar 1, 1956

By Leonard B. Lipson

Boyer, Morgan and Muskat,&apos; with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,&apos; have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/&apos;E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By Leonard B. Lipson

Boyer, Morgan and Muskat,&apos; with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,&apos; have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/&apos;E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

THE assay of all metal ores is made by means of fusion and they are brought to their fineness in the same way as if they were a large quantity. However, I have told you of lead, tin, copper, and iron in their own places, that they are smelted in order to obtain a good assay so that one may know from its weight whether the quantity justifies the expense. This is their assay, for it does not matter whether it be done with great exactness. But the eye is turned with much more care to the assaying of silver and gold, since they are things of value, and one tries to have a more exact knowledge of them. Thus, when you have found the mountain and the vein of ore in it, and have also uncovered it or extracted it from the mine, it is necessary to make an assay of it, for though it is often apparent to the experts what kind of metal it contains, nevertheless they do not know for sure what virtues or evilness it may have unless the light of the assay itself shows them. Therefore it is necessary to extract a quantity in some way that is as free from rock and as good as possible. To a part of this, without any addition, a smelting fire must be applied in order to see whether it can be smelted easily. If it does not smelt by itself, you must consider and try to understand what causes this, for many times it comes from the rock which accompanies it and which contains much dryness and earthiness. I do not believe that one can know this with other judgment than by experiment with powerful and strong fires. Therefore, if the efforts of ordinary methods do not succeed, it is necessary to try to soften them by means of the company of fusible things-now with marble, now with ground glass, now with lead, galena,* or litharge from lead, or with iron scale, or else with the slag of other ores. With small operations even borax, saltpeter, or ochre is used and similar things, as I shall tell you in detail in the discussion of the preparation of ores for smelting. In short, try to see whether they can be overcome by adjustment of the fires or by virtue of the means

Jan 1, 1942

By A. Yazan, M. Sagheer

To meet the demands of the planned development of Turkish steel industry an Iron ore processing plant is under construction at Divrigi, Anatolia and is planned to be commissioned mid of 1978. The plant has been designed for an annual capacity of 4 million tons of crushed magnetitic ore. About 1.9 million tons of coarse concentrate of 25-2 mm size and 1.3 million tons of pellet feed concentrate will be produced by wet screening, dry magnetic concentration of coarse size fractions and wet magnetic concentration of fine size fraction. The fine magnetic concentrate will be reground and filtered to prepare the feed for the pelletizing plant.

Jan 1, 1978

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930&apos;s. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine&apos;s own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine&apos;s power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer&apos;s knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944