Search Documents

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By Walter S. Larsh

The Ruth orebody, so far developed, is roughly oval in plan, major and minor axes about 1600 ft. (457 m.) and 1200 ft. (365 m.) respectively, average thickness about 120 ft. (36 m.), and with a general dip of about 15" to the northwest. According to the generally accepted theory, the ore is a secondary enrichment of the porphyry due to leaching in situ by meteoric waters. Copper occurs as chalcocite, chalcocite coating pyrite, and a little chalcopyrite. The leached zone, or capping, covering the ore varies in thickness from 110 to 540 ft. (33 to 164 m.), average about 410 ft. (124 m.). The ore is blue gray in color, and the capping, light yellow to brown. Ore was first discovered in quantity in the workings from the Ruth shaft, now caved. Further development work was done by churn drills, and the outline of the orebody, as stated above, determined in this manner. Drilling is still being carried on. The porphyry area is entirely surrounded by sedimentaries, limestones, and shales; and, in so far as the underground workings have shown, the porphyry itself, the sedimentaries' near the contact, and the country underlying the ore (igneous or sedimentary) is very soft, heavy, and in places swelling ground. All openings have to be carefully and stoutly timbered, and, after once driven, they have to be constantly eased off and repaired. The mine Is at present served by two shafts, the Star Pointer, the main working shaft, a vertical, and the Ingersoll, an incline used for waste and material. The two shafts are about 2600 ft. (792 m.) apart, connected on the 500 level; a connection is now being driven on the 600 level. (Dec., 1917. This connection is now completed.) The 300 level, which is finished, and the 400 level which is nearly completed, are accessible only from the Ingersoll and connections with the 500 level. The 300 level was developed for and mined by the shrinkage stope system, similar to that used successfully in the Ray Consolidated property.

Jan 1, 1918

By Frank Haas

Many articles on the physical properties of fire damp have appeared in the Transactions and elsewhere but practically nothing has been written in regard to its occurrence or fluctuation in quantity in an ordinary mine. After the Monongah explosion in 1907, with the loss of 361 lives, the Consolidation Coal Co. sought a method by which such catastrophes could be prevented. While the cause of this particular explosion was attributed to coal dust, some of those acquainted with the mine thought that fire damp was involved, if it was not the initial cause. So the literature on the subject was studied and mines where similar conditions prevailed in this country and Europe, were visited, with the view of establishing some system by which gas could be more easily detected and controlled. The results of this study were disappointing for no method was found other than the time-honored fire boss with his safety lamp, with some variations in the rules and regulations governing his inspections and reports. Duties of the Fire Boss Pending the development of a better method, it was decided to standardize and perfect the duties of the fire boss and the reports based on his observations. Those who were then in service were closely examined, various lamps were experimented with and the lamps and individuals tested under known conditions. It was found that a fire boss could tell whether gas was present but his estimate of quantity was not even an approximation; therefore, while the services of fire bosses were indispen-sible there was need of additional information by which the quantity of gas could be estimated with some precision in order to determine its variation from time to time. Chemical Process for Determination of Methane After considering all methods known at that time a chemical process was adopted. The principles involved in the process are that in an enclosed receptacle, in the presence of excess air, methane will be completely burned by means of a hot platinum wire to carbon dioxide and

Jan 1, 1927

By Geo. Otis Smith

Twelve years ago, the Director of the United States Geological Survey addressed to the Secretary of the Interior a letter calling attention to the government's need for liquid fuel for naval use and pointing out that the rate of increase in demand was more rapid than the increase in production.' This letter, in a way, inaugurated the policy of public oil-land withdrawals, which was well founded in its primary purpose of protecting the oil industry and highly desirable in its immediate effect of checking the over-development of that day in California. Unfortunately, however, through delays in legislation, this policy may be regarded now as having outlived both its intent and its usefulness. In 1908, the country's production of oil was 178,500,000 bbl., and there was a surplus above consumption of more than 20,000,000 bbl. available to go into storage. In 1918, 10 years later, the oil wells of the United States yielded 356,000,000 bb1.—nearly twice the yield of 1908—but to meet the demands of the increased consumption more than 24,000,000 bbl. had to be drawn from storage. Nor is this all of the brief comparison. In 1918, our excess of imports over exports of crude petroleum was nearly 33,000,000 bbl. whereas in 1908 we exported 3,500,000 bbl., which was net, as we had not begun to import Mexican oil. In this period, the annual fuel-oil consumption of the railroads alone has increased from 16,871,000 to 36,714,000 bbl.; the annual gasoline production from 540,000,000 gal. to 3,500,000,000 gal. This record may be taken not only as justifying the earlier appeal for Federal action, but as warranting deliberate attention to the oil problem of today. Need of Future Supply The position of the United States in regard to oil can best be characterized as precarious. Using more than one-third of a billion barrels a year, we are drawing not only from the underground pools but also from storage, and both of these supplies are limited. In 1918, the contribu-

Jan 1, 1921

By D. A. Dukelow

By using the U. S. Steel oxygen sensor to measure the oxygen content of the steel, deoxidation practices have been developed for silicon-killed fine-grain steel produced by the basic oxygen process. Measurements of oxygen content taken at final turndown are related to the amount of the aluminum addition to the ladle necessary to obtain the desired aluminum analysis for proper grain refinement. In comparison with heats deoxidized by the standard approach, which is based on carbon content, the heats deoxidized according to the oxygen-sensor-based schedule showed a 25 percent decrease in variability from the desired aluminum content. As more heats of a particular grade are made, it is expected that improved quality will result in decreased rejections and better analysis control. Sensor-based deoxidation schedules are also being developed for semikilled, rimmed, and capped steels.

Jan 1, 1972

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc, may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, to¬gether with the names of its president and its secretary, may be published in MINING AND METALLURGY or the DIRECTORY of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as associates or junior associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied by suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership. The Affiliated Student Societies receive the following privileges: 1 A copy of MINING AND METALLURGY free; 2. The use of Employment Service; 3. The use of MINING AND METALLURGY for publicity purposes, such as printing notices of their activities, etc ; 4. Assistance in obtaining speakers for their meetings, lists of moving-picture films, etc. To retain the privileges of the Affiliated Student Society, its officers must keep in touch with the Secretary of the Institute and advise him of its activities. The foregoing plan is not confined to students in mining engi¬neering or metallurgy. Any undergraduate society of engineers may avail itself of the privileges offered. Societies desiring to be recognized as Affiliated Student Societies are requested to make application to the Secretary of the Institute, giving particulars as to their nature, membership and officers. The accompanying list gives the names of the Affiliated Student Societies as of April 15, 1927, and their presidents and secretaries, in so far as they have been reported to the Secretary of the Insti¬tute.

Jan 1, 1923

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Howard E. Parkinson, John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry's needs. The Bureau programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine communications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved mine communications systems. In May 1975 the U.S. Bureau of Mines (USBM) conducted a mine communications technology meeting to provide a brief overview of the USBM communications technology developments in the past 5 yr. This meeting lasted for 1 1/2 days. Therefore, I have elected to narrow this paper to a brief review of recent underground mine communication developments. The following will be discussed: 1) Ultra-high frequency (UHF) radio for fan hole drill operators;

Jan 1, 1978

By P. Duwez, H. Martens

Dimensional changes generally occur during the sintering of metal powder compacts. These changes may have several causes and their magnitude depends upon the numerous variables involved in the process, such as the nature of the powder, size and shape of the grains, compacting pressure, rate of heating, maximum temperature, length of time at temperature, and furnace atmosphere. Among all the variables, time, temperature, and compacting pressure are probably the most important ones, and the effect of each one of the other variables can be studied separately once the effect of these is well understood. The most precise method of studying the phenomenon of dimensional changes in a compact consists of heat treating the compacts at various temperatures for different lengths of time. In this method, only very small specimens can be used, in order to achieve rapid rates of heating and cooling. The technique involved in these measurements is very simple, but is time consuming. Another experimental approach to the problem consists of measuring the change in length of a compact as it is being heated at a constant rate. Although the two variables, time and temperature, are combined into a single one (rate of heating), the results obtained by this technique may be of great interest from both practical and theoretical points of view. The purpose of this paper is to describe a systematic investigation of the change in length during sintering of compacts made of one or several metal powders. Experimental Procedure The change in lenght of compacts during sintering was measured with an automatic recording dilatometer. In this instrument the change in length and the temperature are recorded as functions of time on two separate charts and the rates of heating and cooling may be varied from 1 to 20°F per min. The temperature may be kept constant at any value up to 2200°F during any predetermined length of time and the change in length recorded as a function of time. Provision is made for atmosphere control inside the fused silica tube containing the specimen. Three different magnifications are provided, so that 1 in. on the chart corresponds to 0.002, 0.005, or 0.010 in. change in length. The mechanism following the change

Jan 1, 1950

The earliest reference to coal in Tennessee is that by Dr. Walker in 1750 (see p. 18) where he saw it near the present site of Middlesboro. The next reference found is in 1798 when Morse stated, "some of these mountains, particularly in the, Cumberland, or Great-Laurel Ridge, are the most stupendous piles in the United States. They abound in ginseng and coal."' There must have been many places where it was seen in that interval, but nearly as long a time elapsed before Morris, in 1834, said that "fine beds of stone-coal exist in both East and Middle Tennessee."2 In a description of the Dover Iron Works, on the left side of the Cumberland River, a few miles above Dover, in Stewart County, it was said that "80 hands were employed in digging and transporting stone coal" and that the "plant had been running at least since Oct. 2, 1834."3 While doubtless coal had been used locally, this is probably the first use of it commercially in the state. The consumption of stone coal was 4,000 tons per year. In this same geological report openings of coal are mentioned near Battle Creek, Marion County, and in Bledsoe and Rhea Counties, where it was being used locally by blacksmiths; some other places were being worked near the turnpike road from Kingston to the Crab-Orchard, the product being hauled three miles to the Tennessee River and loaded in barges; farther west in. White County several outcrops were found. In Fentress County, several pits had been opened, the coal being sent down the Obey and Cumberland Rivers, and openings were also seen in Morgan, Anderson, Roane, Warren, Hamilton and Franklin Counties. The writer had hoped to publish an account of the iron works in the state but was unable to obtain the necessary information. He was told by an old iron-master, Mr. E. Embree, that

Jan 1, 1942

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702' are of interest, not only for

Jan 1, 1969

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 3/4 million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done' on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By B. H. Caudle, A. B. Dyes, R. A. Erickson

The study of the influence of fluid mobilities on the sweepout pattern resulting from the injection of gas or water has been extended to cover the production period which follows breakthrough of the injected material. Mobility ratios over the range common in field operations (0.1 to 17) were studied for several pattern floods (five-spot, staggered, and direct line drive). The experimental data required for these studies were obtained by the use of the x-ray shadowgraph technique using miscible oil phases of different viscosities in porous plate mode1s of a reservoir element. From the shadowgraph pictures obtained before and after breakthrough of the injected fluid, flowing ratios at the producing well and cumulative volumes injected were calculated. The method for applying such data in predicting field behavior is illustrated for a water flood of a five-spot. For this case a range of mobility ratios of 0.5 to 5.0 results in: (I) nearly complete (95 to 100 per cent) sweepout pattern efficiencies at abandonment conditions, (2) production after breakthrough being responsible for as much as one-third of the total recovery at the lower mobility ratios, and (3) a twofold variation in the operating life of the reservoir. In determining the merits of a secondary recovery operation, the fraction of the reservoir which is ultimately to be swept by the injected fluid is of major importance. Because of its significance a large amount of research has been applied to the study of areal sweepout efficiency. Muskat, Wyckoff and Botset1,2 have presented the classic analysis of the pattern efficiency at breakthrough for several injection patterns in which the mobility of the fluids ahead of the injected phase front was equal to the mobility of the fluids behind the front. Aronofsky3 as extended this analysis of recovery at breakthrough through numerical computations and by the stepwise use of the potentiometric model to include the effect of different fluid mobilities ahead of and behind the invasion front on the line drive performance. Fay and Prats' have also employed numerical computations to show the influence of one other condition of fluid mobilities on the five spot flood. In a previous paper' a new method of attack on this problem which employed x-ray and porous plates was described. At that time experimental results were also presented which described the effect of fluid mobilities on the reservoir area contacted by the injected fluid at breakthrough for the five spot and direct line drive patterns. Most of the literature pertaining to sweepout pattern efficiency has emphasized the pattern which is obtained at breakthrough of the injected phase. The increase in the sweepout pattern which occurs after breakthrough

Jan 1, 1955

By F. Brons, V. E. Marting

In the past, other authors.1, 2 have studied the influence of a skin effect on the productivity of a well. This skin effect, expressed by the skin factor S, is considered to be caused by a thin layer of impaired permeability immediately around the wellbore and extending vertically over the whole productive interval penetrated by the well. The skin factor S is defined as follows. Based on this, the impairment in productivity caused by a skin can be expressed by the fractional loss in productivity I, which is the loss in productivity divided by the total unimpaired productivity. For compressible flow in a stabilized well which drains a circular area of radius re, 1 is given by The present paper deals with a different kind of productivity impairment. Consider a well in which part of the productive formation is blocked off completely, either by incomplete penetration or by exclusion of parts of the productive zone by blank casing. In Fig. 1 (A, B and C), three examples are shown. Fig. 1(A) shows the situation where a well only partially penetrates the formation. This often is done to combat the actual or imagined danger of bottom-water coning. Fig. 1(B) shows a well producing from only the central portion of a productive interval. This type of completion is sometimes used where both water and gas coning are a problem. Although the case of a well producing through perforated casing cannot be treated in a manner similar to the previous two cases (where radial flow in the horizontal plane is assumed), Fig. 1(C) shows several intervals open to production and qualitatively describes this case (as will be discussed later). To study the loss in productivity in all these cases, two parameters are introduced which fully determine the impairment. The first is the penetration ratio "b," i.e., the total interval open to fluid entry divided by the total thickness of the productive zone. The second is the ratio hlrw. In this ratio, rw is the wellbore radius. The definition of h is more cumbersome. In Fig. 1(A), h is the thickness of the total productive interval. The streamline configuration for this case of partial penetration is basic to the other two cases considered (Views B and C of Fig. 1). It will be obvious from Fig. i (A) that the flow lines in the uppermost portion of the formation will be essentially horizontal, while those in the lower portion will curve upward toward the well. In Fig. 1(B), with only the middle portion of the zone open to production, the streamline configuration. of the upper half will be an exact mirror image of that in the lower half of the zone. Hence, for the case illustrated in Fig. 1(B), h is defined as one-half the total sand thickness. It follows, then, that in Fig. 1(C) h is one-half the distance between corresponding points in adjacent intervals. (In gun-perforated casing, h would be one-half the distance between perforations.) In a paper by Nisle4 and a paper given by the present authors5, the mathematical theory was developed for the cases under consideration. In the present publication, the emphasis is put on the results of these studies; consequently, the equations derived in Refs. 4 and 5 will be omitted, for the most part. The pressure drop p in a well producing from only a portion of the total formation thickness can, in analogy with Eq. 1, be expressed by Numerical solution of Eq. 5 by use of the IBM 650 leads to the following important conclusions. First, during a short period after starting production (usually on the order of a few minutes), the function p(b) is given by

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paper. The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal.

Jan 1, 1960

By J. P. Witherow

MR. BIRKINBINE'S description of the bad working and sudden chilling of the Warwick Furnace last summer, seems to me quite phenomenal in blast-furnace practice. During my connection with the management of blast furnaces for many years, in the anthracite, coke, and raw-bituminous coal districts, such a case has never come under my notice. It seems to me that the scaffold in the zone of fusion could not have established itself (so that the whole power of the engines, with a blast pressure ranging from 12 to 18 pounds per square inch, could not penetrate), unless the furnace was previously badly scaffolded and bridged in some of its upper sections, from 15 to 30 feet above the hearth level, either in the zone of chemical action or the beginning of the zone of fusion. Such a "barrier to the upward gaseous currents would cause a suspension of combustion which may have superinducedd the scaffold that is assumed to have existed in the zone of fusion. It is Difficult to conceive' that an agglomerated mass almost across the section of the lower bosh should have formed all at once, if the furnace was free and porous for the reaction of the gaseous currents above. Therefore, I think, the Warwick furnace was by no means in as free, open, and fine internal condition at the time the trouble commenced as the description of its regular working would lead us to suppose. I do not question the accuracy of the statements relative to the output of iron, etc. I merely claim that the phenomena., as described, could not have been almost instantaneously developed, unless there had been an incipient seaffold and lodgment above the zone of fusion. I would state my hypothesis to be that the stock lodged or collected in some of its upper sections during the process of blowing-in, on which, as a basis, more or less accumulations may .have lodged, and thus, indirectly, caused the formation of the suc- * This paper was not presented to the Institute in its present form, but is based on remarks, in discussion, by the author on Mr. Birkinbine's paper on, a Short Blast at the Warwick Furnace, and Mr. Witherbee's paper on Two Scaffolds at the Cedar Point Furnace.

Jan 1, 1881

By William E. Ford, Edward Salisbury Dana

430. The more important of the special properties of a mineral species with respect to heat include the following: Fusibility; conductivity and expansion, especially in their relation to crystalline structure; change in optical characters with change of temperature; specific heat; also diathermancy, or the power of transmitting heat radiation. The full discussion of these and other related subjects lies outside of the range of the present text-book. A few brief remarks are made upon them, and beyond these reference must be made to text-books on Physics ant1 to special memoirs, some of which are mentioned in the literature (p. 305).

Jan 1, 1922

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.' For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By P. F. Richardson, J. L. Perisho, W. J. Roe

Handling and transport of coal during the winter months can be a severe problem. The inability to unload frozen coal from rail cars produces serious economic and logistic problems due to transportation delays, rail car shortages, and demurrage on the rail cars. One method of dealing with the problem of unloading frozen coal has been to spray freeze conditioning agents onto the coal before it is loaded into rail cars. Both water soluble and oil based formulations have been used as freeze conditioning agents. The water soluble treatments generally contain a polyhydroxy alcohol, such as ethylene glycol, or salts of alkaline earth metals, such as magnesium chloride and calcium chloride, as freeze point depressants. The oil based treatments consist principally of hydrocarbons, such as No. 2 oil or diesel fuel. The authors' tests have shown significant differences in the effectiveness of these freeze conditioning agents, depending on the particular coal substrate being treated. These differences correlate with the coal porosity and inherent moisture of the substrate. In general, the greater the porosity of the coal, the smaller the effect of the freeze conditioning agents. Coal porosity has a greater impact on water soluble freeze conditioning agents than oil based products. The authors investigated the pore structure of a variety of coals using mercury intrusion. Findings were related to the effectiveness of different freeze conditioning agents as measured by unconfined compression strength tests. In general, coals with a large number of very small pores (between 0.05 µm and 0.03 µm) do not respond as well to freeze conditioning chemicals.

Jan 1, 1986