Search Documents

By L. A. Norman

ANOTHER chapter in the history of Mother Lode mining is being written by operations in the Old Eureka mine near Sutter Creek, Amador County, California. During a two-year period (1938-1939), 85,517 tons of ore averaging 0.62 oz. gold per ton were mined and milled, as compared to the production of approximately 210,000 tons of 0.315-oz. gold ore during the preceding seven years. This is a repetition of mining history in the Mother Lode, where a period of prosperity has followed a long period of lean production. The location of this new ore in the hitherto unproductive hanging-wall greenstones and its mining and geological developments are most interesting. HISTORY OF THE OLD EUREKA MINE The Old Eureka mine, also known as the Hayward, Eureka, Hetty Green and Amador Consolidated, is in the most productive 10-mile length of the 120-mile long Mother Lode of California. The mine was first opened in 1852 with operations more or less continuous for the next 30 years. Production during this period amounted to $12,000,000 from an ore shoot 500 ft. long, which bottomed 1700 ft. below the surface. The shaft was continued as a prospect to 2065 ft. on the incline, where work was stopped in 1881. The mine was sold in 1916 by Hetty Green and the shaft deepened to the 3500-ft. level (3212 ft. vertically) by the new owners. Drifts were run on the 1700, 2100, 3000 and 3500-ft. levels, together with approximately 1500 ft. of crosscuts. No ore was found and work was abandoned in 1921. The present owners, the Central Eureka Mining Co., purchased the mine in 1924 after threatened litigation over rights to the rich ore shoot being mined from the lower levels of the Central Eureka mine on the south. Rehabilitation of the shaft commenced in 1926 and in 1930 mining on the old 2100-ft. level was started. While efforts of the previous owners had been directed for the most part toward the area south of the Old Eureka shaft and adjacent to the productive Central Eureka mine, the present owners started drifting northward on the old 2100-ft. level. On the 2000-ft., 2100 and 2300-ft. levels, drifts were run in part along the

Jan 1, 1939

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By M. J. Sheriff, D. H. Smith, W. Macdonald

The paper outlines the basic procedure used in electrical system planning and design. Consideration is given to the use of applicable codes and standards, development and use of a system One Line Diagram, power availability, load requirements and power factor. Also discussed are the factors influencing the selection of power supply and distribution arrangement, voltage levels, system grounding, distribution and utilization equipment such as switchgear, transformers, motor control, cable systems, motors. Short circuit calculation methods and system protection are discussed.

Jan 1, 1978

By Zay Jeffries

Each generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwithstanding their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization. It will remain for future generations to determine whether there is now going on a gradual change toward greater importance of the non-ferrous metals, as compared to iron and steel. The world's pig iron production in 1920 was slightly more than twice what it was in 1890, whereas the non-ferrous metals production in 1920 was about two and one-half times that in 1890. Every non-ferrous metal industry has shown marked growth during the last thirty years. During this period, the production of cop-

Jan 1, 1924

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By C. Dirksen

This study investigates whether oxygen consumption during segregated forward combustion may be affected by natural convection. Linear theory indicates that thermal instability occurs in a horizontal porous medium when the modified Rayleigh number N 'Ra exceeds a critical value of about 40. Most experimental results, including those described here, indicate this value to be about an order of magnitude smaller. N ', is derived from "differential similarity" and the proper time scale factor is also obtained. The critical value of N'ra for a horizontal, water-saturated porous medium at atmospheric pressure subjected to a uertical temperature gradient was found to be about 3.0. The ambiguity in the value of N'R, arising when fluid properties cannot be assumed constant is indicated. Natural convection was observed for oblique systems below N 'Ra , while simultaneous horizontal flow did not affect N Racrit. The expected range of values for the various parameters pertaining to segregated forward combustion is indicated and the corresponding values of N 'Ra calculated. Only under very favorable conditions, such as high permeability, high pressure and low top temperature, can the critical value of N 'R, be exceeded. Thickness of the convection layer should not become too large, since the time required to obtain significant mixing is proportional to the square of the thickness. For an oblique combustion frant the conditions for significant mixing may be less strenuous. LNTRODUCTION Laboratory1,2 and field314 experiments have shown that a markedly upgraded oil can be produced by in situ forward combustion. Under certain conditions injected air may move through a high permeability, gas-saturated channel over the oil-saturated layer, while combustion takes place, exclusively, at the horizontal interface (Fig. 1). Such a channel may be a natural gas cap, or it may result from a forward combustion process in which injected air and combustion gases fingered through the top of the formation, causing a premature breakthrough at the production well. In this particular case of segregated forward combustion, the air stream moves parallel to the combustion front. Molecular diffusion and transverse mechanical dispersion will be insufficient to cause all the oxygen in the air stream to reach the combustion front. When the oxygen in the air stream is not completely consumed in the combustion process, it will reach the production well and create a serious fire hazard. In addition, the reduced efficiency may make the process economically unprofitable while also serious corrosion problems may be experienced in the production we11.3 This undesirable situation should, therefore, be prevented. However, in a situation as depicted in Fig. 1, an unstable temperature gradient exists in the gas phase. The combustion is taking place at the lower boundary at a nearly constant temperature that may be anywhere from 600 to 1,200F, depending on the conditions. The upper boundary of the gas phase is overlying, impermeable rock; its temperature might be around 100F, but may increase to 300F or higher due to conduction and convection as the combustion process continues. This represents a steep temperature gradient and it is conceivable that under those conditions free or natural convection will take place in the gas

Jan 1, 1967

By Robert H. Merrill, David W. Wisecarver, Raymond M. Stateham

The US. Bureau of Mines, in cooperation with US. Borax and Chemical Corp. and Kennecott Copper Corp., has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of micro-seismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron mine near Boron, CaL, and the Kimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nev. Microseismic monitoring within a frequency band of SO to 5000 Hz indicates noise rates in stable, inactive mining areas are between 0 and 10 noises per hour; the rates in stable, active mining areas are between 10 and 50 noises per hour; and the rate in unstable areas is as high as 2500 noises per hour. High microseismic noise rates in the Liberty pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic technique is applicable to large pit walls, and that the wide-band, wide-range microseismic equipment appears to be suitable for open-pit investigations. The microseismic method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. The method has been used for many years to detect incipient failure in roofs or pillars in underground mines. In 1963 the U.S. Bureau of Mines (USBM) started an investigation of the microseismic method in large, open-pit slope walls. The purpose of this investigation was to evaluate the method in open-pit slopes where the rock may be fractured and broken and where the size of the rock mass under investigation is much larger than normally encountered underground. In addition, both the stresses in the rock and the strength of rock near pits are lower than usually found underground. Consequently, there was some doubt concerning the feasibility of the method for open pits, and the economics of such an investigation may have been prohibitive especially if large walls had to be monitored with closely spaced geophones. The successful application of the microseismic method to underground operations has improved safety at little, or no sacrifice, to production or extraction ratios. The anticipated reward in open-pit mining would be the improvement of safety with a minimum sacrifice to mining operations. There is also a possibility that the method could be used to optimize the unloading (stripping) of potential failure areas by the removal of intact rock from the slope wall rather than the cleanup of a slide from the bottom of the pit. This report contains a brief description of three types of microseismic apparatus used in four different pit walls, each of which is different in height, slope, rock types, or has different planes of weaknesses, such as faults, fractures, or joints. Because the geologic features of the pit walls are varied and complex, for brevity, this report dwells mostly on the microseismic apparatus, techniques, the rock noise rates, and the slope movements measured at the various sites. PROGRESS AND DEVELOPMENT The microseismic method was developed over 20 years ago; and the method and examples of investigations in underground mines are summarized by Obert and Duvall. 1 In more recent years, the method has been applied in several underground mines, and an in-situ test under controlled stress conditions is described by Morgan and Merrill. 2 Experience has shown that, on occasions, the microseismic noise rate and amplitude reach a peak value and then start to decrease before a failure occurs in an underground mine; on other occasions, the noise rate steadily increases to a maximum at failure. The method has been applied to slopes by Goodman and Blake,3 and by Paulsen. 4 Goodman and Blake found that the noises corresponded with failures in the slope

Jan 1, 1970

By Milton E. Wadsworth, J. Brent Hiskey

Galvanic interaction between particulate chalcopyrite (CuFeS2) and copper results in the rapid conversion of chalcopyrite to chalcocite. The effects of temperature, surface area, concentration of sulfuric acid and agitation were systematically evaluated. The kinetics were found to be controlled by a steady-state current flow controlled by the effective anodic and cathodic surface areas involved in the galvanic couple. The experimental activation energy was 11.5 and stoichiometric data and reaction products have been characterized. The overall kinetic system has been evaluated based upon an electrochemical model.

Jan 1, 1974

By Oscar Harder

IT is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing -his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treating high-speed steels. Regarding this research, Dr. Sauveur, (22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and. related materials in the red-heat range, using various methods. . The results, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as its immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By Ernest Burchard

A RECONAISSANCE of the chrome and manganese'1ore deposits of Culm was made in the spring of 191s by Albert Burch representative of the U. S. Bureau of Mines and the writer representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the: United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a mining engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of, the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War Industries Board, and as soon as chemical analyses of the chrome ores could .be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data, and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party. In the study of material for the present paper, chemical analyses have been made by R. C. Wells and petrographic determinations and descriptions were furnished by Miss E. F. Bliss, both of the U. S. Geological Survey.

Jan 9, 1919

JAmes E. Howard, Watertown, Mass.:—In connection with this paper, it is the desire of the Watertown laboratory to receive suggestions as to the lines of work and the particular direction along which the examination of the ingot-metal should proceed, and any suggestions so offered will be noted with care, and the tests conducted so as to embrace such features as it is thought desirable to have investigated. To me the question of structural continuity seems of para-

Jan 1, 1909

By J. H. Klepinger, C. W. Goodale

I. Introduction....................567 II. Character oF the OrE................568 III. Old FluE System..................572 IV. Tests on Old FLUE System..............575 1. Aspiration Tests................. 575 2. Tests with Steel Settling Chamber........... 575 3. Test with Experimental Brick Flue........... 583 4. Testa on Blast Furnace Geses............. 591 V. Design of New FluE System.............. 597 VI. Main Dust Chamber................. 605 VII. Some DetailS of Construction ............. 609 VIII. THE Chimney.................... 616 IX. Operation of New FluE System............. 624 X. Temperatures and DraFTS............... 630 XI. Velocities and Volumes................ 632 XII. TeStS on the New FluE System............. 637 XIII. Conclusion..................... 643 I. Introduction. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and as this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 1, 1914

By AIME AIME

PRESIDENT Edwin Ludlow and Secretary Bradley Stoughton made their first-trip of the year 1921 to visit Local Sections of the Institute, and talk over Institute interests and policies, during the early part of April. The main purpose of the trip, as usual, was to bring back to headquarters suggestions or comments on the Institute's work on the part of, members. The trip was made a brief, one by the necessity of remaining in New Fork until Apr. 1, and of the attendance of President Ludlow at a meeting of American Engineering Council and. the organization of a Philadelphia Section of the Institute in Philadelphia on Apr. 16.

Jan 1, 1921

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950

By A. C. Fieldner

THE older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer, I who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter "g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 5, 1925

By Theodore B. Comstock

The existing topographical features of the United States present many points of interest to the student of dynamical geology, but there is, perhaps, no subject which offers a more promising field for investigation than the relations between the geological structure and the mineralogical characteristics of the principal mining districts. There are seven prominent culminating points in the relief of North America, each one of which can be used as a type of the physical features of all the others. Again, if we divide these seven elevated districts into two sets, we shall discover a still more striking parallelism between the individual members of each group. But the most remarkable revelation is the fact that each one of these points is more or less closely the centre of an area of economically important mineral resources. It is interesting to note in this connection that six of these mineral tracts lie mainly within the borders of the United States, three of them being almost wholly in our territory. For

Jan 1, 1883

By J. E. Johnson

At the Cleveland meeting of the Institute in October, 1912, I had the honor to present a paper outlining the conditions surrounding the charcoal iron industry…

Jan 1, 1915

By Alan Arias

On grinding in pure water, zirconium, tantalum, iron, and stainless-steel powders were extensively comminuted and simultaneously oxidized with hydrogen release, whereas nickel, copper, and silver powders did not react with water and their particle sizes increased. On grinding nickel, copper, and silver in water pressurized with oxygen, nickel and copper became extensively comminuted and were oxidized, whereas silver did not react with oxygen and its particle size increased. From these results and other considerations , it is hypothesized that for extensive comminution of ductile metals and alloys to occur on grinding they must react with the grinding media. UlTRAFINE metal and alloy powders are finding an ever-growing number of applications in metallurgy and in other fields.' Of particular interest are ultrafine metal and alloy powders suitable for dispersion strengthening.2'9 Various research programs on dispersion strengthening are being carried out and in some of these programs the ball-milling method is being used to produce dispersion-strengthened materials. This method usually involves the simultaneous grinding of metal or alloy and a dispersoid followed by consolidation of the resulting powder mixture. To obtain the ultrafine powders required for dispersion strengthening,' grinding is carried out in many liquids, including aqueous and nonaqueous media, with or without grinding aids.4'5 Nonaqueous liquids usually contain water as an impurity and some grinding aids may contain water of hydration.5 The water present may affect the grinding process. The writer has shown5 that. on ball milling chromium in water, the chromium is oxidized and hydrogen is released. It was surmised that the same reaction may occur on ball milling other metals and alloys in waterbearing liquids. Therefore, the investigation of ball milling in water was extended to metals and alloys other than chromium. In the course of the investigation, however, it became apparent that the data-to-gether with the results from a few additional experi-ments—could be used to postulate a comminution mechanism for ductile metals and alloys. A well-known comminution theory is that of smekal.7 According to this theory, comminution is possible because of the weakening effects of surface cracks and other imperfections in materials. This theory imposes a lower limit of about 1 µm for the ground particles. The beneficial effects of liquids and additives on the rate of grinding are well known.8 Mechanisms by which liquids and additives may aid in grinding were reviewed by Rose and Sullivan.' One aspect of these effects is based on Rehbinder's theory of crack propagation in materials under stress.9 According to Reh-binder's theory, liquids or additives may promote the spread of cracks in stressed materials by lowering the surface tension at the crack tip. Rose and Sullivan surmise that the same mechanism may be operative during grinding, thereby facilitating comminution of the particles. In addition, Rose and Sullivan reviewed how additives may act as dispersants as a result of their being adsorbed on the surface of the particles being ground. This concept has been suggested by Quatinetz, Schafer, and smea15 to explain from their experiments the major role of additives that enabled them to grind metal down to 0.1 µm. Discussions of other comminution theories and additional sources of material on the subject will be found in Ref. 10. None of these previous suggestions and theories, however, can account for all phenomena encountered during ball milling of metals to submicron size in this and in a previous investigation by the author.6 The objectives of this investigation were to determine the behavior of metal powders during ball milling either in pure water or in oxygenated water and to gain an insight into the grinding mechanism. Zirconium, tantalum, iron, nickel, copper, and silver powders were ball-milled in pure water. These metals were selected because their oxides cover a wide range of free energies of formation. For comparison purposes, an alloy-type 430 stainless steel-was also ball-milled in pure water. The pressure of the hydrogen released during ball milling was monitored in order to determine the oxygen that combined with the metal or alloy. In order to obtain more information on the nature of the grinding process, nickel, copper, and silver powders were also ball-milled in oxygenated water (water pressurized with oxygen). The oxygen that reacted with the powders was determined from the pressure decrease in the mills. The powders resulting from ball milling in pure water and in oxygenated water were subjected to surface area, optical microscopy, and X-ray diffraction analyses. With these data, the oxygen calculated to be combined with the metals during ball milling, and comparison of the free energies of formation of the oxides of the milled powders with that of water, a comminution mechanism was postulated. MATERIALS, EQUIPMENT, AND PROCEDURES The materials used in this investigation were powdered metals, deaerated distilled water, high-purity helium, and commercial grade (99.5 pct purity) oxygen. The powdered metals used were zirconium, tantalum, iron, nickel, copper, and silver. A 16 pct Cr, ferritic stainless steel, type 430, was also used. The purities (or nominal compositions) and the surface areas of these metals and the alloy are given in Table I.

Jan 1, 1970