Search Documents

By Carl Swartz

METALLURGISTS differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a one-millimeter screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in, color, having the general characteristics of a spinet Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution zinc values tied up in this compound remain behind. HISTORY In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite, others merely a mixture of zinc and iron compounds.

Jan 1, 1927

By S. T. Wlodek

The scale md subscale reaction products were identified and their rates of formation were studied in air over the range 1600" to 2000°F (871 " to 1149°C) for periods of up to 400 hr and for hoth the solution-annealed and aged conditions. The effect of prior sltrface preparation on suhscale oxidation was also studied The general oxidation behavior of both Ni-Cr-Mo-Al-Ti type alloys was similar. A surface film of a, Al2O3, forms immediately on exposure Subsequent oxidation continued at a linear rate (QL = 55 * 5 kcal per mole) as colonies of Cr2O3 nucleated at the A12O3/gas interface Further oxidation proceeded at a paraholic rate zvhiclz could he fitted to two successive rate constants. During paraholic oxidation, and depending on temperature, the scale consisted of Cr2O3, NiCr2O4 , and TiO2 with traces of NiO. In the case of Rene 41, the activation energy of both paraholic processes was 66 * 3 kcal per mole suggesting that diffusion of cations tlzrozrgh Cr2O3 was the rate -determining process. An unusual decrease in the oxidation of Udimet 700 at 1900°F where a spinel of Ni(A1,Crh0, zuas the predominant reaction product prevented the accurate assignment of activation energies for this composition. In both alloys internal oxidation of Al2O3 commenced shortly after parabolic scaling was observed. Prolonged exposure prod7tced intemal oxidation of TiN, and in Udimet 700 a complex Mo-Ni nitride was also found. At 1900oF, the subscale reactions in Udimet 700 undergo an inversion which parallels the decrease in surface oxidation; internal oxidation ceases hut is replaced by the formation of "spherodized" 3.' colonies. Surface-preparation techniqtles which introduce appreciable working, such as coarse surface grinding or grit blasting. increase the amount of alloy depletion and internal oxidation in Reni 41. The reverse is true of Udimet 700 for which electropolished or mechanically polished specimens show much more subscale oxidation than strongly worked stirfaces. The strongest commercial nickel-base alloys presently available are generic to the Ni-Cr-Mo-A1-Ti base which exploits the precipitation of Ni3(A1,Ti) as the main strengthening mechanism, while relying on solid-solution strengthening by molybdenum and chromium reinforced by the pre- cipitation of carbides to attain maximum properties. This study characterizes the oxidation behavior of Rene 41, the strongest alloy of the Ni-Cr-A1-Ti type commercially available in sheet form, and Udimet 700, whose higher aluminum and titanium content allows it to exhibit one of the more attractive combinations of high-temperature properties available in a wrought product. The scaling processes of complex, type nickel-base alloys have received relatively little attention. Malamand and vidal as well as Poulignier et al.2'3 have determined the composition gradients across the metal/oxide interface produced by high-temperature oxidation and considered the effect of surface perature, Limited weight-gain data has also been published by Fere 5 for alloys of this type and Radavich6 has identified the reaction products on Udimet 500 and Inco 702 after oxidation at 1832°F. Reference can, of course, be made to the excellent reviews of Kubaschewski and Hopkins7 or Ignatov and Shamgunova8 for a summary of the data available on the oxidation of binary and ternary alloy systems which are related to the more complex alloys considered here. EXPERIMENTAL The analyses of the different commercial heats studied are given in Table I. Using the experimental procedures previously established,9 continuous weight-gain data were obtained on both heats of Rene 41 sheet (A and B) and 150-mil-thick slices of cast Udimet 700. Subscale oxidation reactions were followed by static exposure of cylindrical specimens obtained from swaged Rene 41 (Heat C) and Udimet 700 (Heats E and F). In brief, continuous weight-gain tests were performed on specimens with a surface area of 10 to 12 sq cm. These were abraded through 600 grit Sic paper, electropolished to 2p rms in an electrolyte of 10 pct H2So4 in ethanol, and lightly etched in 10 pct HCl in ethanol before final washing and rinsing in ethanol. All continuous weight-gain data were obtained in dried (-70°F dew point) flowing (1 liter per min) air to an accuracy of +0.1 mg. Subscale oxidation processes were followed by the metallographic examination of 0.5-in-diam by 1.0-in.-long specimens. After an initial center-less grinding, various additional surface treatments were employed to determine the effect of surface preparation on subscale oxidation processes. Before exposure in zirconia crucibles, all samples were lightly etched in 10 pct HCl-ethanol, washed in ethanol, and dried. The depth of internal oxidation was measured to ±0.00025 in. on unetched specimens mounted so as to provide a taper mag-

Jan 1, 1964

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray 'analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949

By T. S. Blair

I feel a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

By William L. Fink, H. R. Freche

This is the thirteenth paper of a series from the laboratories of the Aluminurrl Company of America presenting the results of investigations of equilibrium relations in aluminum-base alloys prepared from electro-lytically refined aluminum. The ninth paper, on The Constitution of High-purity Aluminum-titanium Alloys,' presented a type of system that had not previously been encountered in aluminum alloys. Subsequent work has shown that there are several similar binary aluminum diagrams including that of aluminum and chromium. The present investigation was limited to the cxtreme alnminum end of the aluminum-chromium system. The first systematic investigation of the aluminum-chromium equilibrium diagram was carried out by Hindrichs.? The resulting equilibrium diagram with some imaginary additions suggested by Guillet3 is shown in Fig. 1. Recently Goto and D6gane4 investigated the constitution of aluminum alloys containing up to 32 per cent chromium, and presented the diagram that is reproduced in Fig. 2. Wide discrepancies in the two diagrams are evident. The following intermetallic compounds have been reported in the literature: A1Crl5,6 AlloCrlzSi,5 AlCr4,6 AlCr3,7 AlaCr.8 Preparation of Alloys and Chemical Analyses With the exception of sample Y4206, which will be described under Determination of Hyperperitectic Liquidus, the alloys were prepared from electrolytically refined alurninum% Of which the analysis is given in

Jan 1, 1933

By Charles S. Barrett, Robert F. Mehl

A study of the structures arising from the decomposition of the ß solid solutions in the Cu-Zn and the Cu-A1 systems is of peculiar interest in the study of the mechanism of precipitation from solid solutions. It is possible in these alloys, by varying the composition within the ß field, to precipitate from the same basic lattice phases having different lattice structures. It has been rather generally assumed heretofore that the type of structure originating from the decomposition of a solid solution— the Widmanstätten structure—-is determined by the lattice structure of the parent solid solution alone. In the first paper of this series1 evidence was advanced which threw doubt upon this hypothesis; but definite proof of the correctness or incorrectness of the hypothesis should be forthcoming from a study of these alloys, for if the structures originating, for example, from the precipitation of the a phase from ß and of the ? phase from the ß in the Cu-Zn system should be shown to be crystallographically different, the hypothesis would necessarily be held as definitely disproved. Furthermore, the newer proposal enunciated in the first paper of this series—that the origin of the Widmanstätten structure lies in a cooperation between the lattice of the parent solid solution and that of the precipitate-—which at present seems the only a1ternative hypothesis, would in such an event be given added weight. The work here reported shows that the Widmanstätten structures originating in the precipitation of the a phase from the ß and in the precipit'at.ion of the y phase from the y in the Cu-Zn system are indeed crystallographically different; and incidentally presents some new descriptive information on the Widmanstätten structure from a more general point, of view.

Jan 1, 1931

By R. J. Wysor

Since the outbreak of the European war, few problems of raw-material supply have commanded more nation-wide attention than potash. It is well known that before the war the domestic production of potash was an insignificant percentage of the imports. The average annual importation of raw potash salts for several years prior to 1914 was slightly over 300,000 net tons, and of other potash manure salts about 700,000 tons. The sudden and almost total cessation of these imports created a unique and stringent situation. Methods of recovering potash from feldspar and other native mineral sources, and reclamation from hitherto waste products, have received a marked impetus. Soaring prices have been a keen incentive to research and industrial development. Although several brief articles concerning the possibilities of potash recovery have appeared in recent trade journals, it still may be a matter of some surprise to the average technical mind that potash might be reclaimed as a profitable byproduct in the manufacture of pig iron. At the present time it may be of special interest to present some data, largely of a technical nature, on this subject. A fairly thorough search of the literature reveals a number of articles concerning salts of the alkali metals in the blast furnace. Many of them deal with the theoretical rôle of alkali cyanides in the furnace. Several discuss the probable effect of the alkalies on the furnace brickwork. Two or three ambitious patents have been granted for reclaiming potash or other products from blast-furnace gas. However, we have heard nothing further as to the practical application of these patents. Little literature of importance has appeared during the last 10 years concerning alkalies in blast-furnace practice, and I have discovered no record whatsoever as to the actual sale or commercial disposal of flue dust for its potash content until this was inaugurated in our plant at Bethlehem. A bibliography of the most important articles discovered is appended. About 4 years ago, in the course of investigating blast-furnace stove efficiencies, I analyzed the fine, yellowish fume of which a considerable

Jan 1, 1917

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By AIME AIME

IT is unlikely that any oil field has ever threatened the future course of the oil industry as does Kettleman today. It seems that nature has striven to outdo herself in combining in this field every possible factor conducive to a tremendous production of the petroleum product in greatest demand-gasoline. This field already has 13,700 acres of proved land and an oil zone of known thickness of 1400 ft. It has wells yielding several thousand barrels of oil of virtually motor fuel grade, together with millions of cubic feet of gas at almost unheard of pressures. The field would have been the. answer to an oil man's prayer in times of under-supply, but now it is the oil man's nightmare, for drilled in -the manner of most other fields and without regard to available markets for oil and gas, the greatest physical and economic losses in the his¬tory of the oil industry will result.

Jan 1, 1930

By A. T. Shurick

THE NRA Administrator's casual reference to the coal code as the next "pineapple" to be fixed was a conservative estimate of his job. This thorny and adamantine morsel now looms as a critical test of NRA. A failure in coal supplies would have the gravest potentialities in the Administration's program at this time. And the loss of prestige from a breakdown of the enforcement machinery in this initial large-scale test of strength would accentuate the incipient indications of insurrection in other directions. General Johnson has had a difficult task. It involves problems festering for a quarter of a century. A succes¬sion of Presidents have been glad to tide over their respective regimens with inconclusive expedients; they have been baffled by the complexities of the technical angles and hopelessly irreconcilable concepts of powerful conflicting interests with large issues at stake.

Jan 1, 1933

By Arthur F. Wendt

IN 1697 King William the Third granted unto his well-beloved subject Adolph Philipse, a certain tract of land, now known as Putnam County, N. Y. At the death of Adolph Philipse the land descended by inheritance to his nephew, Frederick Philipse. In 1751 his surviving three children partitioned the surface into nine parcels and divided them equally amongst themselves, but reserved the mineral rights which they held in common. Thus, at this early period in the history of the colonies, the existence of valuable deposits of iron-ores in Putnam County seems to have been a matter of common knowledge. Yet it is only within the last five years that the county has become a prominent, producer of iron-ore. Desultory mining had been carried on before that period at the Sump, Croft, arid Tilly Foster mines, but only a limited output was achieved, and few of our iron-masters suspected the existence of an abundance of good ores only forty miles from New York harbor. The accompanying map shows the location of those deposits of ore which are now generally known, and have been worked to considerable extent. Without doubt there are many more still awaiting the miner's pick, for no systematic exploration has ever been attempted within the borders of the county. Geologically, the occurrence of the ore is a counterpart of that of the New Jersey and Lake Champlain magnetites. The countryrock, and even the physical geography, are identical. Many small lakes dot the surface of the county. It is from these and their tributary springs and streams that the metropolis derives its farfamed Croton water. Abrupt hills divide the lakes and ponds. Some of the lakes, notably Lake Mahopac, are on the crest of hills, and are fed by subterraneous springs. The prominent mines of the county, in the order of their productiveness, are the Tilly Foster, Mahopac, Croton Magnetic, Sump, Croft, and Island mines. Of these, the first two are at present the only producers, and are quite exceptional in their nature. In fact they are the only ones of their kind in the Appalachian range, if not in the world.

Jan 1, 1885

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950

By Philip Bucky

THE term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater mecha-nization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar model built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimensions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein.

Jan 1, 1938

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,' catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.' have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200' C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927