Search Documents

By M. R. J. Wyllie, H. W. Patnode

In the quantitative interpretation of electric log data it is essential to know the formation factor, defined as the ratio of the resistivity of the formation 100 per cent saturated with brine to the resistivity of the brine.' This concept implies that the formation factor for any given rock is constant irrespective of the resistivity of the brine or solution with which it is saturated. It is apparent that this can be true only when the rock matrix is wholly non-conductive. As reservoir rocks may contain clay or shale having an appreciable conductance one may expect these constituents to influence the determination of true formation factor. The formation factor may be theoretically derived from log data by dividing the resistivity of the mud filtrate invaded formation by the resistivity of the mud filtrate. Such a method of calculntion has implicit in it the assumption that the fluids in the invaded formation are wholly replaced by mud filtrate. that the solid matrix is non-conducting, and that the formation factor of the invaded zone is identical with the formation factor of the uninvaded zone. Since the validity of the first two basic assumptions regarding the insulating character of porous matrices and the displacement of the interstitial fluids in porous media do not appear to be fully established, the formation factors of a number of cores and clay slurries have been measured under conditions suitable for verifying the assumptions and the extent of any errors inherent in them. CORE STUDIES Apparatus and Procedure Resistivity measurements were made on short cylindrical permeable cores which had been previously mounted in lucite.2 The cores were clamped by means of insulated bolts between brass plates about 5 cm square and 1 cm in thickness. The plates were provided with a ring seal to prevent leakage between them and the core mount, and had a centrally located orifice so that fluids could be flowed through the mounted core. The brass mounting plates were used as electrodes and any current flow between them necessarily passed only through the constituents of the intervening core. Fluid saturation of the core, and fluid flow through the core, were effected by a centrifugal pump connected to the outflow end of the core, thus providing a differential pressure across the core of approximately one atmosphere. The procedure used was first to evacuate each core by means of the pump and then to saturate the core with an aqueous sodium chloride solution of known resistivity. The resistance of the core was measured and flow of the solution through the core continued for sufficient time to establish a constant resistance reading. After equilibrium had been reached with one solution, another sodium chloride solution of a different resistivity was flowed through the core and the flow continued until a constant resistance reading was again obtained. This procedure was continued until resistance measurements of the core had been made with a series of solutions within a salinity range from 1.0N NaCl to distilled water. The data obtained enabled the apparent formation factor of given porous rocks when saturated with fluids of different resistivity to be computed and also provided information regarding the ability of an invading fluid to displace interstitial water from a core. Results Berea Sandstone — The first core examined was a specimen of Berea sandstone." This core had been cut essentially parallel to the bedding for permeability studies. The core was clamped in the core holder and saturated with 1.0N NaCl solution and the resistance determined. It was subsequently flushed and the resistance measured when saturated in turn with 0.1N, 0.025N, 0.01N, .005N sodium chloride solutions and finally with distilled water. In flushing the core with each

Jan 1, 1950

By V. F. Swanson

A petrographic study was made of the type and sources of mineral contamination occurring in Florida phosphate rock products. Emphasis was placed on contaminants in the screened rock (+1 mm), since this portion of the product undergoes no physical beneficiation except for scrubbing to remove slimes. Since iron and aluminum contents of the finished product affect the salability, special emphasis was placed on identifying types and sources of these contaminants and relating chemical composition to visual characteristics. Wavellite derived from the overburden was the major aluminum contaminant with some aluminum being included as secondary clay balls. Iron occurred as phosphates in the overburden and as colloidal oxides included in the phosphate pebbles. Chert and limestone contamination derived from the Hawthorne formation underlying the phosphate matrix.

Jan 1, 1972

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

By R. W. Gurry

Thermodynamic calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganese, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B2O3in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1944

ALASKA Established November 19, 1947 Regular meetings fourth Monday of each month except June, July, and August Theodore A Loftus, Chairman John C Boswell, Vice-Chairman Patrick H O'Neill, Secretary-Treasurer Box 1034, Fairbanks, Alaska District Vice-Chairmen Robert L Thorne, Juneau, Alaska Alfred J Lomen, Jr , Nome, Alaska Donald G. Wilcox, Anchorage, Alaska

Jan 1, 1952

By R. R. Sayers

Ventilation may be defined as the process by which vitiated air of an enclosed or partly enclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level Per Cent. Oxygen.................................................. 20.94 Nitrogen................................................. 78.09 Carbon dioxide........................................... 0.03 Argon................................................... 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxide, ammonia, ozone........................................ traces Carbon Dioxide Limit For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent, carbon dioxide. Nevertheless, in mines it sometimes occurs in sufficient quantities to cause symptoms in men or even unconsciousness and death. One-half of 1 per cent. of carbon dioxide in normal air causes a slight and unnotice-able increase in the ventilation of the lungs, that is, a man exposed to one-ha,lf of 1 per cent. of carbon dioxide will breathe a little deeper and a little faster than when in pure air. If 2 per cent. of carbon dioxide is in the air, the lung ventilation will be increased about 50 per cent.; if there

Jan 1, 1927

By E. C. Weichel

THERE have been many attempts at permanent roof support in anthracite mines, in some cases brick arches, in others concrete, and also combinations of brick or concrete walls with steel beams. These supposedly permanent roof supports have frequently failed when heavy pressure is brought to bear upon the structure, because they are so rigid that failure occurs because the structure is unable to adjust itself to the increased load. Roof pressure exerts a tremendous weight, and it is at times difficult to find any means of support which is strong enough to bear the entire pressure, unless this supporting structure has in itself the element of some flexibility which will enable the structure to hold the moving mass until it "arches" itself. If the supporting medium has flexibility enough so that it can adjust itself to the heavy initial loads, and so give the overlying material an opportunity to form a self-supporting arch, then such a roof support will be more useful than any rigid roof support. There has recently been introduced into the anthracite region a new form of gangway lining that is flexible enough to slightly adjust itself under heavy pressures, and so give the loosened material which is being supported a chance to form into an "arched" mass. This lining, manufactured under patents granted to Hans Schaefer of Essen, Germany, was introduced in the United States in the summer of 1928, at which time the Amercan licensee, Richard Howells of

Jan 1, 1930

By Earle E. Schumacher

THE elements silicon and germanium are not metals within the usual, intuitive association of the word, nor are they so within a stricter definition based on the electronic binding. Two properties associated with metals are plasticity and high electrical conductivity. These elements crystallize in the diamond cubic structure, an arrangement apparently not very favorable to slip, and are therefore brittle rather than ductile. Their electrical conductivity is not like that of metals the atoms are locked together by the covalent bond, which in pure and perfectly arranged material leaves but few electrons free to act as electrical carriers.† In further contrast to metals, their electrical conductivity can be greatly increased by raising the temperature. Yet silicon and germanium are not ideally nonmetallic. They are hard, solid, and possess a metallic luster. They exhibit that peculiar brand of electrical conductivity conveniently termed "semi- conduction," wherein, as shall be seen, lies much of their importance. Both, but silicon in particular, are important components in real metallic alloys and the methods of their reduction and preparation lie clearly in the province of the metallurgist. From their duality of physical and chemical properties, silicon and germanium, along with such elements as boron, diamond, gray tin, selenium, antimony, and arsenic, are considered semimetals or metalloids. Because of their importance to metallurgy and the im-

Jan 1, 1953

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By T. Turner, C. L. Zimmerman, U. Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 km north of Atlanta, GA. The project consists of: a 28-m high dam, a 0.9-m diam outlet conduit, an emergency spillway, and a 4.0-m diam hard rock transbasin diversion tunnel. This flood-water management system was part of Cities Service Co. mine safety program for the Cherokee ore body, which is partially located within the creek channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1981

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By Edward Hanrahan

September 1981 I'm here today to report on a revolution -- a revolution in the way the Federal Government looks at energy. I'm not talking about a simple change in the relative emphasis on sources -- such as more recognition for coal and nuclear power, with less rhetoric about "soft- technology." Nor am I describing a mere change in focus -- from the demand side to the supply side. And I am not referring exclusively to our obvious goal of budget cuts. No, I'm here to discuss a fundamental change in Federal direction -- one that started as soon as President Reagan was inaugurated, and one that is articulated in the National Energy Policy Plan he sent to Congress in July. That brief policy document was backed up by three volumes of supporting data; but I think I can catch it's flavor for you in just three phrases: * First, various energy forms complete with each other and complement one another. * Second, fair competition among them (which includes honest pricing) will give us the best "energy mix." • And, finally there may be ligitimate arguments about where Federal responsibility in regard to energy spills over into Federal interference; but it's about time we drew the distinction -- and eliminated the latter. This Administration's national energy policy is quite different from any we have had in recent years. It is tuned to human nature and changing times. We are seeking the best practical solutions in the energy -a lot better than the ones we have been offered before, but still something less than perfection. One way we do that is by counting on a fully informed public to guide it's own destiny. And, instead of treating energy as an isolated entity, we recognize it as part of the overall economy. The President's Program for Economic Recovery is as much a factor in energy policy as the specific actions of the Department of Energy. One striking difference from the past energy policy 1s that this policy plan does not say: "In 1985 we will -produce so many hundreds of millions of tons of coal: . . . or . . . "By the end of this century the Nation will be deriving X percent of it's electricity from wind generators." Unfortunately, targets like these are what many people have come to expect from the Federal Government -- and what they think of as energy policy, whether the figures hold up in the long run or not. But . . . think about it! Nether the Department of Energy nor any other part of the Federal Government produces coal, or mines uranium, or manufactures solar collectors. There are only a few sections of the country where the Federal Government generates and sells electricity. So it does not take any great insight to recognize that the amount of energy we will produce or consume as a Nation In the future depends on many factors beyond direct government action. And those future totals cannot be predicted precisely, anyway -- by the Government or by anybody else. According to our way of thinking, the choices should be up to the people. When the free market works within a healthy economy, individuals express their preferences in the marketplace -- adjusting the balance of all energy factors continually in a way that no computer could be programmed to reflect perfectly. So, instead of having the Government issue a rigid set of numerical goals, our main concern simply is that there be enough energy. We want the Nation itself to decide how much that should be, what form it should take, and how that energy should reach consumers. The marketplace decides. Considering the recent past, this is indeed a revolutionary idea. It has some pitfalls, and we won't reach this ideal of free choice overnight. But that is where we are headed. And I'll offer some evidence in a few minutes that the policy has already started working. First, let me give you some of it's highlights: 1) Nobody who appreciates the philosophical underpinnings of this Administration will be surprised that the energy policy shows faith In domestic energy production and the supply side of the economy; but it also recognizes the important role of energy conservation -- the wise and efficient use of energy resources.

Jan 1, 1982

By R. E. Somers

THE Appalachian field is notable for four tests drilled in recent years to depths of over 7000 ft. and for one commercial gas well at 6822 ft. The latter is the Ligonier well and produces from the Oriskany FIG. I.-NATURAL GAS PRODUCTION OF PENNSYLVANIA AND WEST VIRGINIA. sandstone. Together with several other comparatively deep tests, these holes were drilled in search of natural gas, to make up for the decline in production of the field. The production curve of Pennsylvania FIG. 2.-EAST WEST SECTION OF APPALACHIAN FIELD. (AFTER ASHLEY AND ROBINSON, PENN. G. S.) and West Virginia from 1907-21 is given in Fig. 1 to illustrate the heavy decline from the peak of 1917. This diminishing supply has also been shown by Moyer,1 on the basis of decreasing rock pressures.

Jan 3, 1924

By John E. Sherborne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons.l-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applications of phase behavior have been made to specific cases pertaining to critical phenomena.l2-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. Definition of Terms In a discussion of this sort, a definition of terms used is most important. Such terms as "pressure," "temperature" and "volume" need little definition other than mention of the units in which they are considered. Pressure is expressed in pounds per square inch absolute. Temperature is usually expressed as degrees Fahrenheit or degrees Rankine. In considering thermodynamic and phase behavior, the use of the absolute, Rankine, scale is desirable. Volume is expressed as specific volume, such as cubic feet per pound. This will be recognized as the reciprocal of the specific weight. In considering systems composed of more than one component, it is sometimes desirable to consider molal

Jan 1, 1940

By John E. Sherborne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons.l-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applications of phase behavior have been made to specific cases pertaining to critical phenomena.l2-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. Definition of Terms In a discussion of this sort, a definition of terms used is most important. Such terms as "pressure," "temperature" and "volume" need little definition other than mention of the units in which they are considered. Pressure is expressed in pounds per square inch absolute. Temperature is usually expressed as degrees Fahrenheit or degrees Rankine. In considering thermodynamic and phase behavior, the use of the absolute, Rankine, scale is desirable. Volume is expressed as specific volume, such as cubic feet per pound. This will be recognized as the reciprocal of the specific weight. In considering systems composed of more than one component, it is sometimes desirable to consider molal

Jan 1, 1940

By Ancel St. John

At the New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,' in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papcrs which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangc-mcnts were therefore made to present that evidence at this meeting. Material Examined The material exalllined was high-ernission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. Scope of the Investigation The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of t.horia detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

By Charles S. Robinson

Abstract-The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains, about 80 km (50 miles) west of Denver. The ore body is being developed for mining by workings that extend more than 1100 m (3500 ft) below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson B Associates Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentay rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreases with time. The rate of decrease inflow (or pressure) is exponential. By measuring the change inflow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 8, 1978

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

Jan 1, 1897

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965