Search Documents

By Jacob Reeese

I HAVE discovered a new method by which steel and other metals may be burnished by the automatic action of the burnishing machine, and by which the cost is greatly diminished, and more perfect work produced. And in addition to the polishing and burnishing action of

Jan 1, 1881

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By E. E. White

I disagree with Mr. Brinsmade on serveral points, and I will discuss this remards under the same six topics which he has used.

Jan 1, 1915

By W. Evans, C. E. Ells

The agglomeration of hydrogen in pure aluminum and A1-Mg alloys has been studied through use of hydrogen introduced into the metal by cyclotron proton irradiation. Both the growth and dispersal of the agglomerates have been followed by metal-lographic techniques. During the cyclotron irradiation, agglomeration occurs at temperatures i 100°C for hydrogen concentrations as low as 1 ppm. On heating at elevated temperatures, 300°C to 600°C, intragranular agglomerates first coarsen and then disperse. The agglomerates formed at grain boundaries are much larger than the intragranular agglomerates; with hydrogen concentra- tions > 10 PPm, heating for 1 hr at 500°C results in extensive grain-boundary cracking. The hydrogen agglomerates have been shown to inhibit grain growth, but no inhibition of recrystallization has been observed. The ability of hydrogen to enter aluminum at a free surface, combined with its high-diffusion rate at elevated temperatures, accounts both for growth and dispersal of the agglomerates. Irradiations at elevated temperatures give results consistent with the explanation proposed for agglomerate behavior on post-irradiation heating. 1 HE formation of hydrogen-filled bubbles, or blisters. in aluminum and its alloys has been studied for over' thirty years. The work up to 1952 has been reviewed by Kostron' and since then Ransley and

Jan 1, 1963

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By Percy Gillie

THE Tralee preparation plant, owned and operated by the Semet-Solvay division of Allied Chemical and Dye Corp., is located on the Virginian railway, near Mullens, Wyoming County, W. Va., and the mine, which is in the Winding Gulf district, produces coal exclusively from Pocahontas No. 3 seam. The property, comprising 4900 acres, is leased from the Pocahontas Land Corp. Prior to 1930 four separate mines were operated in this tract, some having been started about 1916. Plans for the preparation plant were formulated soon after World War 11. Construction began in the spring of 1948, operation early in 1950. The plant was designed to be operated with minimum labor. It was equipped for production of first quality graded sizes of coal for house heating and 3/8x0-in. slack suitable for high-standard metallurgical coke. In the beginning, a thorough investigation was made of the property by means of core drilling, prospect openings, and sections from shallow mines on the property, as well as sections and analyses from mines in the immediate vicinity. After the extent of desirable coal had been established and the average seam section and nature of overlying and underlying strata had been determined, it was decided to install a system of mining which would load the full seam and would clean the product mechanically. Pocahontas No. 3 seam is characterized by draw slate and bone and rock partings. It was not known what the washing difficulties and cleaning plant requirements would be for processing the raw product of full mechanical mining. Arrangements were made, therefore, through the courtesy of the property owner, to obtain a large sample from a section of the mine along the adjoining property line. The

Jan 1, 1954

Discussion of the paper of GEORGE S. RICE and H. H. CLARK, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2563 to 2571. NORMAN V. BRETH,* Pittsburgh, Pa.-It was my privilege to visit in the last two months on behalf of the U. S. Bureau of Mines 10 mines where electric shot-firing systems controlled from outside the mine are installed. I will describe briefly what I saw in some of these mines, which are located in Utah, New. Mexico, Oklahoma, Alabama, and Kansas. At a mine in Utah, 230-volt alternating current is used to fire the shots, which is taken from a small transformer in the substation. The shot-iring circuit is independent of all other wires and is tested for grounds every day. There are no lightning arresters on the firing circuit. Porcelain insulators are used inside of the mine, and glass outside. The switches are situated as follows: One in the substation, one in, the shot-firer's cabin, two at each cross entry; where the shot-firing circuit crosses the trolley wire a switch is placed on either side of the entry in series with the shot-firing circuit. The miners are checked in and out of the mine. The coal is undercut and is shot down with permissible explosive, the shots being connected in multiple. There are 75 to 110 shots fired each day. A great many times there are no missed shots. If not more than two or three are missed they are left until next day. The fan is kept running at full speed when the shots are fired. The shot-firing switch is closed only once and the whole mine is shot at once. At another mine in Utah, power wires are used for shot-firing circuits; 500-volt, direct current is used to fire the shots. The only sizes of wire used outside of the power wires are Nos. 8 and 14 B. & S. gauge. The return is connected to the pipe lines and track. Porcelain insulators are. used inside of the mine.

Jan 4, 1915

By C. D. Young

IN an effort to employ cast steel of a stronger structure than that found in the annealed steel castings, the possibilities of heat treatment which will increase the strength without materially decreasing the ductility may be resorted to. The following abstracted report (which is a brief outline of what has already been clone by the Pennsylvania Railroad Co. at its shops and Test Laboratories at Altoona, Pa.) is of material interest, as it indicates what may be done with steel castings when properly treated, thereby permitting in railway service greater strength of cast steel parts without any increase in weight or space. The question of the heat treatment of alloy steel castings is not taken up in this paper. The obscurity formerly surrounding the heat treatment of steel has been for the most part removed by the development of our knowledge of the critical points of steel, pyrometers, furnace construction, and the testing of the finished product. The operations of the heat treatment proper will be taken up under the heads of (1) heating for quenching; (2) quenching; (3) drawing. (1) Heating for Quenching.-Heating for quenching is best conducted slowly, especially in the case of castings of variable thickness. Cracks may occur either in heating or in cooling, clue to different temperatures at different points of the casting. The castings should be thoroughly soaked at the maximum temperature (generally 1,500° to 1,600° F.), 1 hr. being sufficient for sections 1 ft. in thickness. The minimum temperature which will produce the desired hardening effect will, in all cases, be found to be the most satisfactory, as the grain coarsens when the critical range is exceeded to too great an extent. All temperatures should be governed by a checked pyrometer with the hot junction to the heated object, and with several couples in a large furnace to insure a uniform temperature.

Jan 2, 1914

The opening session was held on Tuesday evening, June 28th. Mr. F. S. Witherbee, of Port Henry, a member of the Local Committee, welcomed the Institute as follows: Mr. President and Gentlemen and (if I my also add) Ladies of the Institute: In the absence of the Chairman of our Local Committee it is my pleasant duty to give you a cordial welcome once more to the shores of Lake Champlain. I think some fourteen years have passed by since we last had the pleasure of receiving you at a meeting in this vicinity ; but the pleasure of that meeting still lingers in our memory; and the profit which we derived from your discussions and from your presence with us has made us heartily desirous to have you here again. If the truth must be known, we were for a time much embarrassed by the difficulty of providing adeqriate and comfortable shelter for the large number of friends whom we hoped (and, as this assembly indicates, had good reason for hoping) to receive. But the liberality and zealous co-operation of the Delaware & Hudson Canal Company and its hotel manager, in offering to open Hotel Champlain, at no little inconvenience, before the usual time, presented a solution of this difficulty, provided the date originally proposed for the meeting could be changed to a week later. This change was duly authorized; .and I think you will all agree with us that it was wise.. At all events, I am sure, I now need offer no apologies for the roof which covers yau. During the fourteen years which have elapsed since your last visit to us, great strides have been made in the industrial development of this country. The meetings of the Institute, held from one end of the land to the other, have permitted you to witness the transformation of small hamlets? like Birmingham, Ala., into populous and thriving industrial centers. You have seen the Minnesota and the

Jan 1, 1893

By John B. Mertie

More than 200 minerals are known that contain the rare-earths and thorium. Monazite and bastnaesite, however, are the principal commercial sources of the rare-earths, and monazite is the principal source of thorium. Monazite was in demand in earlier years mainly for its content of thorium, which was used in the manufacture of Welsbach gas mantles; but beginning in the latter part of the nineteenth century, the rare-earths became progressively more important than thorium. Recently, however, the tenor of thorium in monazite has again become a matter of commercial interest. Rare-Earths and Thorium The rare-earths proper are defined by spectroscopists as the oxides of 14 elements with atomic numbers ranging from 58 to 71; but more commonly lanthanum, with an atomic number of 57, is also included, in which case these 15 elements are often designated as the lanthanides. Chemists also include scandium and yttrium as elements of the rare-earths. A second group of elements, beginning with actinium and including thorium, protactinium, uranium, and all the transuranium elements so far produced, with atomic numbers ranging from 89 upward, are chemically and structurally related to the lanthanides, and are known as the higher rare-earths or actinides. Berzelius discovered that the lanthanides could be separated roughly into three groups, based upon the solubility of their double salts, R2(SO4)3-K2SO4-2H2O, in excess of K2SO4. This separation, with the substitution of sodium for potassium, is still used commercially. The double salts of the cerium earths were found to be almost insoluble; the terbium earths, partly soluble; and the yttrium earths, completely soluble. Based upon the degree of solubility, scandium belongs with the cerium earths; and yttrium belongs with, and gives its name to, the yttrium earths. These three groups with their atomic numbers are shown below. [ ] The prevailing state of oxidation for the rare-earths is R2O3, but cerium may readily be oxidized to the tetravalent state, in which condition it may be separated chemically from the other cerium earths. Praseodymium and terbium may also exist with the valence IV, and samarium, europium, and ytterbium may have the valence II. Most of the elements of the rare-earths, however, are very difficult to separate, and their initial isolation required the work of many chemists over a period of 150 years.20 Fractional crystallization, fractional precipitation, and ion exchange are the principal methods so far used, and fractional precipitation is now employed commercially on a large scale. Ion exchange columns are

Jan 1, 1960

By Werner Schwartz, Wolfgang Haase

Lead sulfide concentrates, which may include other lead concentrates, are sintered on an up-draught sintering machine without the addition of any diluting agents or fluxes. Subsequently they are melted in an oil- or gas-fired rotary furnace. The sintering and melting processes are based upon the following roast-reaction: PbS + 2 PbO = 3 Pb + SO, PbS + PbSO, =2 Pb + 2 SO, For obtaining a lead bullion free from sulfur, the sintering process is carried out in such a way that the sinter product contains a small amount of excess oxygen above that to react with the sulfides. At the end of the melting process, when the reactions are finished, the remaining small amount of oxide residues is reduced with coal to which a certain percentage of soda ash (about 1 pct of the lead bullion) is added. For the lead smelting process described neither coke nor fluxes—except soda ash—are required. This process is being utilized by a European smelter successfully and with a high lead recovery. The consumption figures for the smelting of 100 tons per day of lead concentrates are indicated. The lead content of the lead concentrates from modern ore dressing plants ranges from 65 pct to above 80 pct. In most lead smelters of the world these concentrates are smelted in a blast furnace. For blast-furnace smelting the concentrates have to be desulfurized and agglomerated by sintering. A requirement for the perfect operation of a down-draught sintering machine and of a blast furnace is a maximum lead content in the feed of 40 to 45 pct. For this reason, some lead concentrates have to be diluted by adding return slags, limestone, and possibly iron oxide and sand. As an example, 100 tons of lead concentrate with 72 pct Pb would contain 13.5 tons of gangue (including the zinc). To produce a perfect sinter with 42 pct Pb it would be necessary to add 70 tons of flux and return slag, more than five times the original weight of the gangue, to the sinter mix and blast-furnace charge. A correspondingly large amount of coke would be required in order that all of these materials reach the heat of formation and the melting temperatures of the slag (1200" to 1400°C) inside the blast furnace. The roast-reaction process presents a possibility for lead recovery without dilution of the concentrates. In this process the concentrate mixed with coal is placed upon a Newnam-hearth and air is blown through nozzles into the heated mix. AS a result metalllic lead and a relatively great amount of so-called .'Grey Slag" with a lead content of 25 to 35 pct are formed. The slag is sintered to eliminate sulfur and, after addition of the requisite fluxes, treatt:d in a blast furnace. Owing to the poor recovery of lead from the hearths and to the unavoidable heavy hand-work plus the risk of poisoning this process is utilized in very few 112ad smelters today. Since in mxny countries of the world coke is expensive and difficult to obtain, it appeared feasible to use the principle of the roast-reaction by modern sintering and melting methods with recovery of the lead in electric, or oil, gas, or coal-fired furnaces. Two processes are utilized on an industrial scale: A) Lead smelting in the electric furnace of the Bolidens Gruv A/B in Sweden, as described by S. J. Walldcn, N. E. Lindvall, K.G. Gorling, and S. Lundquist. B) The self-fluxing lead smelting of Lurgi Gesell-schaft fiir Chemie und Huttenwesen m.b. H., Frankfurt a M, Germany, which is described in this paper. In the Boliden process referred to above the sinter mix is pelletized by enveloping return fines with layers of flue dust, limestone powder, and dried galena concentrate. The roasting and agglomeration are carried out on a down-draught machine, and a slight excess of sulfur is left in the sinter product. During the smelting in the electric furnance the roast-reactions occur and a slag poor in lead and a sulfur bearing lead are formed. This latter is subsequently oxidized in a converter to obtain lead bullion and dross. The Lurgi-process achieves the maximum possible extent of the roasting reaction on the sintering machine. The wet flotation concentrates are blended with return fines (lead content 70 to 80 pet), any existing flue dusts and lead slimes—but without the

Jan 1, 1962

By Harry M. Mikami

Refractories are heat-resistant, generally nonmetallic materials used as the linings of furnaces or high temperature vessels in the steel, iron, nonferrous metals, glass, cement, lime, ceramic, chemical, petroleum, paper, and power and heat generation industries. Refractories must have structural strength at high temperatures but also, in many applications, must simultaneously resist chemical-physical corrosion-erosion from stags, metals, granular solids, or gases. Among the major uses are the pyrometallurgical processes for producing iron, steel, copper, aluminum, nickel, lead, zinc, etc. Rotary cement kilns, glass tanks, refineries, utility boilers, chemical and ceramic (including refractories) plants, and a myriad of other smaller scale users employ refractories in the high temperature parts of their operations. Thermal, chemical, and structural conditions under which refractories are used differ widely so there is a great variety of refractories to fill the various needs. Two major classifications are the "basic" and "acid" types. Basic refractories include magnesia and chromite, singly and in combinations, dolomite, and forsterite (olivine). The acid category includes aluminosilicates, alumina, and silica. There are a number of other specialized types such as carbon, graphite, silicon carbide, zircon, and zirconia that have important applications but are used in much smaller amounts than the major categories. Physically, refractories can be divided into bricks and shaped products on the one hand and unshaped or monolithic products (also termed specialties) on the other. There are many further subclassifications and divisions, a discussion of which is beyond the scope of this chapter; see Refs. 2 and 9. Raw materials for the principal basic refractories are magnesia and chrome ore. Magnesia, generally termed magnesite or periclase, is obtained mainly from seawater or saline brines extraction, but substantial amounts are produced from mined magnesite (MgCO3). Dolomite (CaCO3•MgCO3), another important basic refractory, is obtained entirely from mined sources. Acid refractory raw materials are: fire clays, flint clays, kaolin, and other natural clay minerals; aluminosilicate minerals such as kyanite, andalusite, sillimanite, pyrophyllite, bauxitic clays; calcined refractory grade bauxite, alumina from the Bayer process for the alumina group; and quartzitic rocks for silica refractories. The total value of all refractories shipped in the United States in 1974 was $989 million, a record to that date. Of this amount, about 73% represents bricks and shaped products and 27% is in nonshaped or monolithic products which comprise mortars, cements, castables, plastics, and ramming and gunning mixes. Fig. 15.4E.1 shows the rising value of all U.S. refractory shipments in the period 1948-1974. Values of brick and shapes paralleled

Jan 1, 1976

By K. J. Richards, W. J. Schlitt

A combination of industrial and laboratory data is used to explain the interrelationships between operating parameters and cementation plant performance as measured by copper recovery and iron consumption. The chemical factors considered are the relative concentrations of copper and ferric ions in solution, acid concentration, the possible buffering action of other dissolved salts and solution temperature. The effects of flow conditions, solution oxidation, the presence of metallic copper and retention time are also considered. Based on the various relationships developed, possibilities for plant optimization are discussed.

Jan 1, 1974

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

By Grover J. Holt

In order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.0.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the " straight wash " ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces—namely, low price of product and minimum amount of fines—iron-ore concentration oil has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. the I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1947

Jan 1, 1967