Search Documents

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

COAL is perennially -a subject of major interest at. Pittsburgh, but during the week of Nov. 19 to 24 it was especially to the fore because nearly two thousand persons gathered to take part in the second of the international conferences organized by President Baker of the Carnegie Institute. From the opening session on Monday morning when those attending were welcomed by President Baker and T. P. Gaylord, president of the Chamber of Commerce of Pittsburgh, until the party returned from the Clairton coke ovens on Saturday. afternoon, there was something going on all the time, and usually three sessions were in progress at once.

Jan 1, 1928

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By L. L. Wyman

Previous studies1 by the writer dealing with the embrittlement of copper have been concerned with the behavior of various pure and deoxidized coppers when exposed to an oxidation-reduction cycle, and the consequent evaluation of these materials on the basis of their resistance to this action. No attention was devoted to the variations in penetration of embrittlement with time, when these copper materials are exposed to a strong reducing gas, such as hydrogen, nor to the variations in oxygen penetration, with time and temperature, into the "pure" coppers. The cause of the embrittlement is the reduction of the oxygen in the copper by the hot reducing gas, so that a consideration of time, temperature, the occurrence of hydrogen and oxygen must be given. For the purpose of differentiating some of the involved factors, the present work may be divided into two separate series of experiments. The first of these deals with the oxidation of purified coppers under various conditions and then the subjection of these to a standard hydrogen treatment. The second series concerns the reduction, under different conditions, of tough-pitch coppers of several oxygen contents. The resulting data will give the rates of oxidation, and of reduction, for the materials involved. The first series of experiments will reveal how rapidly copper may become oxidized, while the second series will indicate how rapidly embrittlement will penetrate into an oxygen-containing copper when it is exposed to hydrogen at different temperatures. Materials For the purpose of determining these variables, three types of material were selected, to cover the extremes in the ranges of materials commercially obtainable. The first class of materials is represented by an oxygen-free copper, as well as the high-purity vacuum-melted copper2 used in previous work. These materials were selected to determine the variation of oxidation with time and temperature, by oxidizing these coppers under various combinations of these factors, and noting the effect as indicated by a

Jan 1, 1934

Jan 1, 1915

By P. A. Witherspoon, S. P. Neuman

Evaluating the permeability of a caprock overlying a potential gas storage reservoir is a very critical problem. Pumping water from the reservoir can be used as an evaluation tool in analyzing this problem. Fluid level changes that occur in the aquifer us well as in the caprock can be measured with appropriately placed wells. If the leakage of water from the caprock into the aquifer is considerable, the effects will be apparent in the aquifer. If the leakage is slight, however, it will not be possible to detect it with certainty from observations in the aquifer alone. Fluid level measurements in the caprock must be relied upon. and improved methods of analyzing such effects have been developed which are based on a theoretical analysis of fluid flow through a caprock of infinite thickness. An example applying these methods to field data is discussed. INTRODUCTION One of the most critical problems in evaluating an aquifer gas storage project is determining the tightness of the caprock overlying the formation to be used as the storage reservoir. A formation that has previously held oil or gas obviously has a suitable caprock, but an aquifer that contains only water gives no such assurance. A number of aquifer projects in the United States have been troubled by gas leaking out of the intended storage zone, and the ensuing difficulties have led to the development of new evaluation methods. One of these new methods is pump testing wherein water is removed from the aquifer at some controlled rate prior to injection of gas. This fluid withdrawal causes a pressure drop to move out through the aquifer for considerable distances in a matter of days or weeks. Depending on the properties of the caprock, a pressure transient can also pass upward (as well as downward) through the caprock layers adjacent to the aquifer. Thus, if the operator has placed observation wells at appropriate distances from the pumping well, the rapidity with which the pressure transients reach different points in the system can be used to investigate the fluid transport properties of both the aquifer and its caprock. The usefulness of pump testing has been recognized by groundwater hydrologists for many years as a means of determining the potential yield and properties of aquifers used in water supply They have introduced the term "leaky aquifer" for a system in which an aquifer is overlain (or underlain) by semipermeable caprock layers. The ease with which water leaks into the aquifer during pumping can, of course, be very beneficial in bringing additional water to the pumped well. Hydrologists have therefore devoted considerable attention to this prob-lem. From the gas storage standpoint, however, the tighter the caprock layers that overlie the intended storage reservoir, the better are the conditions for minimizing or eliminating any vertical migration of gas. Thus, after a suitable geologic structure has been found, the emphasis in aquifer storage projects is in determining that the caprock is tight. Attention has recently been focused on the use of pump testing as one approach to solving this problem.23,24 This paper presents a further development on evaluating the permeability of a slightly leaky caprock when the caprock is of infinite thickness. From the practical standpoint, this means that the caprock layers are thick enough that pressure transients do not reach the outer boundaries of the system during the pumping test. In a subsequent paper, an analysis of the case where the caprock is of finite thickness will be presented. PREVIOUS WORK ON LEAKY AQUIFERS Jacob" developed a partial differential equation describing the flow of water in an aquifer of permeability k that is overlain by a leaky caprock of permeability k'. Fig. 1 shows a schematic cross-section of the system under consideration. One of his principle assumptions was that if k > > k', the direction of flow is essentially vertical in the caprock and horizontal in the aquifer. Neuman19 confirmed the validity of Jacob's assumption using a mathematical model. Another assumption was that a permeable source layer overlies the caprock (Fig. 1) and is able to maintain a constant hydraulic head at the upper boundary of the caprock. By neglecting the effects of compressibility within the caprock, Jacob1* developed a solution for a bounded circular aquifer. Later, Hantush and Jacobx5 used the same assumptions to solve the case of an infinite radial aquifer that is pumped at a constant rate. Their solution may be expressed in di-mensionless parameters by

By F. V. Lenel

Resistance sintering under pressure is a method of hot pressing in which a powder compact is subjected to pressure and simultaneously heated by passing a low voltage high amperage current through it. Equipment for this process is described. Its basic characteristics such as resistance requirements for powders and compacts, temperature distribution in compacts, and gas reactions during resistance sintering are discussed. Examples of the sintering process in compacts made of a single metal or an alloy powder and in compacts made of mixtures of powders are presented. Potential commercial applications of the process are evaluated. THE usual sequence of operations in commercial powder metallurgy is to compact metal powders in a die at room temperature and sinter the compact subsequently without applying pressure while the compact is in the sintering furnaces. In hot pressing, on the other hand, the compacting and the sintering are combined. The loose powder, or in many cases a cold formed compact, is inserted into the die which is held at the hot pressing temperature, the compact is left in the die until it attains its temperature, and then pressure is applied and maintained for a given length of time. The die may be heated by surrounding it with a suitable furnace, by high frequency induction heating, or by passing current through the die. In hot pressing, compacts of high density and good mechanical properties can be produced in a relatively short time. One of the principal difficulties in hot pressing is the lack of suitable die materials which will have adequate strength at the hot pressing temperature. This difficulty can be overcome at least partially by heating only the material to be hot pressed without heating the die directly. This can be done by passing a low voltage high amperage current through the material and simultaneously subjecting it to pressure. Either loose powders or compacts can be hot pressed by this method in which the desired temperature is produced by the power dissipated in the metal powder. This method of hot pressing has been termed "electrical resistance sintering under pressure." The most significant differences between this operation and conventional hot pressing are: 1—The sintering times are very short, usually a fraction of a second and at most a few seconds. 2—The powder and die are initially cold. 3—Heat is generated within the powder itself and not conducted in from the die. 4— The pressure used is high. 5—Cooling following sintering is rapid, amounting to a quench. Resistance sintering of metal powders under pressure has been suggested repeatedly. In 1933, G. F. Taylor' proposed an apparatus which consisted of an insulating tube made of glass, or a ceramic filled with the powder to be pressed, and plungers above and below the powder. The powder was to be heated by passing an electric current through it and pressure was then applied. The apparatus was intended principally for hot pressing cemented carbides. Although the principle of resistance sintering under pressure is clearly shown in this patent, few details are given. A sintering period of a second or a fraction of a second, which is terminated by the operation of an inertia switch, is mentioned but no values for current density are mentioned. Low pressures, such as atmospheric pressure or a somewhat higher pressure exerted through a lever, are suggested. W. D. Jones' discussed electrical resistance sintering under pressure and proposed using resistance welding apparatus for this purpose. In a patent issued in 1944, G. D. Cremera described a method of electrical resistance sintering under pressure using resistance welding apparatus which was to be applied mostly to nonferrous metals such as copper, brass, bronze, and aluminum. Current densities of 400,000 amp per sq in., sintering times of 1 and 2 cycles of 60 cycle current, and pressures of 5 to 10 tsi are proposed. Cremer suggested using an

Jan 1, 1956

By Donald W. Scott, Adam Wesner

This paper describes the study of 23 nonmagnetic iron-formation samples from the Mesabi Range and shows the significance of their chemical, mineral, and physical properties in terms of their concentration. Data presented here resulted from a research project carried out from 1942 to 1952 by 10 major producers of iron ore, working in conjunction with Battelle Memorial Institute. THE inevitable depletion of Mesabi direct-shipping iron ores, hastened by recent wars, has increased the importance of developing methods to concentrate iron-formation materials. Many mining companies, independent research organizations, chemical companies, and equipment manufacturers are devoting attention to this important work. It is only natural that magnetic iron-formation materials have received major emphasis, since magnetic recovery methods apply and reserves of Mesabi magnetic taconites are large. However, the nonmagnetic* iron-formation materials are likewise believed to represent a large reserve and their study has not been neglected. tions over the years have shown that in addition to the unenriched taconite, which is dense and hard, and the direct-shipping ore, there are transition taconites grading into the friable wash, or intermediate ores. The transition taconites are less massive than the unaltered taconites and usually coarser-grained. This variation, coupled with the fact that there were no extensive drillings in the unaltered taconite, posed a most difficult problem of obtaining samples that would be representative of large tonnages of the fresh rock. The problem was increased by the tremendous extension of the nonmagnetic formation materials on the Mesabi and by the question of their accessibility to mining. A drilling program was evolved that would surmount these difficulties. Selection of samples was made by a committee representing producers in the area. The samples were procured from 1—taconite walls near bodies of stripping burden or wash ore and 2—from shafts in the process of being sunk through taconite for drainage or mining operations. Most of the samples were obtained from the cherty horizons because it became obvious early in the program that the slaty horizons represented an exceedingly difficult concentration problem, owing to the character of the gangue minerals and the fine grind required for liberation of the valuable minerals. More samples were procured from the lower cherty horizon than from the upper cherty because it was more accessible to mining. It is not known how well the samples selected represent the nonmagnetic iron-formation material. However, they were chosen by people Well acquainted with the geology of the Mesabi range and the mining problems involved. It is believed that they represent a fair cross-section of the types of materials that will be encountered. Table I gives data on the origin of the 23 samples and the horizon footages from which they were obtained. Samples 1 through 10, and 15 and 16

Jan 1, 1955

By H. D. Dahl, P. C. Thakur

This paper presents an analysis of a new tool for improved productivity in coal mining: the horizontal drilling system developed by Conoco/Consol. The analysis includes a brief description of the system; discussion of the three categories of advance exploration application of horizontal boreholes; and a survey of other special mining methods planned around long horizontal boreholes.

Jan 1, 1983

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

By J. A. Hafford, J. K. Kerver, J. G. Richardson, P. M. Blair, J. S. Osoba

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By J. K. Kerver, J. S. Osoba, J. G. Richardson, P. M. Blair, J. A. Hafford

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By J. M. Karpinski, F. P. White, R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball, the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corp.'s Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about 50% without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1972

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

By Lawrence Burkhart, S. B. Joo

A hemispherical, constant volume drop with forced internal circulation was considered as a model approximating a real drop at a similar stage of formation Axially symmetric steady flow within a drop contaminated by surfactants was described by solving the full Navier-Stokes equations written in terms of a meridian plane stream function Rotational flow occurred inside the drop above a computed Reynolds number of 5.8, and the change in interfacial flow caused by imposing a surface-tension gradient at the surface had a significant effect on the internal flow Although the work is quite fundamental in nature, the rotational flow described in the paper is responsible for much of the bulk transport of solute to the interface in hydrometallurgical processes such as solvent extraction.

Jan 1, 1981

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By Frank M. Brewster

The handling of congealing oils and paraffin is a serious problem in the Appalachian fields, particularly because the small amount of oil produced per well makes the removing of paraffin a very costly operation per barrel. Few operators realize or have any means of knowing just how much production is lost on account of paraffin depositing over the face of the sand and plugging the pores of the sand; but where paraffin has been removed the production increases indicate that this loss has been considerable. Many operators believe that paraffining is confined to the tubing and pumping equipment, but it is evident that the most serious damage occurs on the face of the sand and a short distance back in the pores. This paper is an attempt to disseminate information on methods and processes in use in the Eastern fields for combatting losses of production and operating difficulties caused by deposition of paraffin in the pores, on the walls, on the tubing and on other pumping equipment. Mills1 covers this subject so thoroughly that excerpts, abstracts and quotations from his work have been used freely in this paper. Nature oF Paraffin Mills states: "The so-called paraffin that collects in oil wells, and in the pores of the producing sands immediately around the wells, is generally made up of amorphous wax or uncracked paraffin, asphalt, or other gummy hydrocarbons mixed with more or less water, oil and inorganic silt. Some of the samples of this paraffin collected from oil wells in different fields and examined by the Bureau of Mines contains as much as 20 per cent. by weight of water and inorganic silt, whereas other samples are composed entirely of waxy hydrocarbons and oil. The inorganic silt accompanying this 'paraffin' is mostly fine sand, clayey materials, common salt and finely disseminated precipitates of calcium and magnesium carbonates. Sulfates of calcium, barium and strontium are less common constituents of paraffin.

Jan 1, 1928

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959