Search Documents

By William P. Shinn

MR. GAYLEY'S admirable paper on the " Development of American Blast-Furnaces" has set forth very fully the history of the development of the Edgar Thomson furnaces since the construction of Furnaces A and B ; but it throws no light on the genesis of these furnaces. That earlier history it is the purpose of the present paper to record. Mr. Gayley truly says: "A new era in the manufacture of pigiron began in 1880 with the putting in blast of the Edgar Thomson furnaces." That era had its beginning with the construction of

Jan 1, 1891

By G. Bhat, J. F. Libsch

lsoembrittlement curves depicting the influence of time and temperature in the range 800' to 1260°F (425' to 680°C) on the development of embrittlement in a commercial chromium alloy steel and a commercial molybdenum alloy steel are presented. Two distinct regions of embrittlement occur in the chromium alloy steel: I—at 800' to 1000°F (425' to 540°C) and 2—in the region just below the lower critical temperature. Embrittlement is most pronounced at 800' to 1000°F, decreasing very rapidly with increasing temperature above this region, only to increase again as the lower critical temperature is approached. The data suggest two distinct modes of embrittlement with possible superposition of the two modes at extended embrittling times in the temperature range 1100° to 1150°F (590' to 620°C). While the molybdenum alloy steel shows little susceptibility to embrittlement at 800' to 1000°F (425' to 540°C), considerable embrittlement may occur just below the lower critical temperature. THE subject of temper embrittlement in alloy steels has received considerable attention in the last few years. Points of view on the mechanism of embrittlement differ, however, resulting in part from the incompleteness of the data developed and in part from the speculation regarding the susceptibility of plain carbon steel to temper embrittlement. Libsch, Powers, and Bhat1 carried out short-time embrittling treatments on an AISI 1050 steel and demonstrated that hardened plain carbon steels are quite susceptible to embrittlement when tempered in the range from 850°F (455°C) to the lower critical temperature. The isoembrittlement diagram,' representing the embrittling characteristics of this steel, is reproduced in Fig. 1. It is evident from the shape of the curves shown that embrittlement in plain carbon steel increases progressively with both temperature and time in the embrittling range. A comparison of the isoembrittlement diagram for AISI 1050 steel with that presented by Jaffe and Buffum' for an SAE 3140 steel shows that up to 930°F (500°C) the isoembrittlement characteristics of the plain carbon steel are similar to those of SAE 3140 steel, although the embrittlement is much more severe in the latter steel. Above 930°F (500°C), the rate of embrittlement in the plain carbon steel increases continuously with increasing temperature; whereas, in the SAE 3140 steel, the embrittlement rapidly decreases. The influence of alloying elements upon embrittlement during tempering thus appears to cause a decrease in embrittlement above the region of maximum embrittlement, i.e., 850" to 1000°F. The question naturally arises as to what effect individual alloying elements have upon the embrittling characteristics of the plain carbon steel. Current knowledge on the influence of alloying elements on temper brittleness may be found in the review papers of Hollomon" and Woodfine. Hollo-mon," from the results of other investigators, has shown that, in general, the amount of embrittlement increases with increasing alloy content (except for molybdenum and possibly tungsten and columbium). Jaffe and Buffum," by a comparison of the embrittlement in a plain carbon steel with that of a SAE 3140 steel postulated that the presence of alloying elements in moderate amounts tends to retard the development of temper brittleness. It is difficult to determine what effect chromium has upon temper brittleness, since most of the information available has been based on the combined effect of other elements with chromium, particularly nickel and manganese. However, Wilten, and recently Jolivet and Vidal,' Vida1, and Woodfine have reported that chromium steels are temper brittle, that the embrittlement is reversible with a maximum rate of embrittlement at approximately 975°F (525"C)," and that the susceptibility increases with increasing amounts of chromium. Taber, Thorlin, and Wallacel" have found a large embrittling effect with increasing chromium content in a medium C-Mn-Ni steel. But Hultgren and Chang," from their experiments conducted on synthetically prepared ternary Fe-C-Cr alloys, could not conclude that these alloys are susceptible to temper embrittlement. However, on addition of manganese or phosphorus, these Fe-C-Cr alloys became susceptible, from which fact they concluded that the embrittlement developed in chromium-bearing Fe-C alloys is due chiefly to the presence of these elements. Considerable data are available to show that molybdenum decreases the susceptibility of steel to temper embrittlement. However, its effectiveness in preventing or decreasing embrittlement appears limited to its presence in small amounts. Vidal" has shown that a plain 2 pct Mo steel was susceptible. Hultgren and Chang" also have shown that molybdenum additions in excess of 2 pct to synthetically prepared Ni-Cr steels did not prevent embrittlement. Jolivet and Vidal' and Lea and Arnold found that molybdenum reduced temper brittleness. Lea and Arnold further stated that molybdenum decreased the rate of embrittlement rather than the total amount of embrittlement, whereas Preece and Carter" have shown that the presence of molybdenum greatly reduces the equilibrium extent of the change at a given temperature but does not appear to influence the rate of embrittlement. There appears to be very little information as to how molybdenum by itself affects the temper brittleness susceptibility of a plain carbon steel.

Jan 1, 1956

The Mexican Government is building a mill at Churunibave in Sonora to handle lead, zinc, and copper ores. This development was sparked by increased mining activity in Mexico and Arizona caused by the Korean war. Pickands Mather, acting for a group of iron ore producers, is negotiating an agreement with Steep Rock Iron Mines, Ltd. to explore and perhaps lease iron ore property covering more than 1000 acres in the Steep Rock Lake area in Western Ontario. Plans call for the early commencement of an exploratory program. Other members of the group by Pickands Mather are Bethlehem Steel, Youngstown Sheet & Tube, the Steel Co. of Canada, and Interlake Iron Corp.

Jan 3, 1951

By A. C. Backeberg

There is no South African code for the design of reinforced concrete headframes, and all those erected have been designed on a uniform basis which, up to the present, has tended to be conservative. With certain exceptions designs have generally conformed with British Standard Code of Practice C.P. 114. In the design of reinforced concrete headframes the following loads are taken into account:

Jan 11, 1961

By AIME AIME

THE accompanying photograph: submitted by C. L. Bransford, assistant district manager of the Republic Steel Corp., in Birmingham. Ala., shows the remains of the old Tannehill blast furnaces, one of the first furnace plants in the South. They were built by Moses Stroup and operated during the Civil War period, when cannon balls were cast there. The record day's run of this furnace plant was said to be 30 tons of iron. The furnaces were fed by a water-wheel-operated bellows and used charcoal, a product of the neighboring forest. They were first owned and operated by the Pioneer Mining & Manufacturing Co., that later became the Republic Iron & Steel Cu., and subsequently the Republic Steel Corp. in that district.

Jan 1, 1936

By Charles E. Glass

The stabil ity of engineered embankments subjected to earthquakes has received considerable attention in the last 10 years, but most of the effort has been directed toward stability of earth dams. Based upon past performance, earthquake- induced failures on non-impounding mine waste structures will likely correspond to small, local slumps or debris slides, and their stability should be considered as an integral part of mine economic planning. As such, stability considerations should include earthquake hazard, characteristics of earthquake ground motion, dynamic slope stability, and the impact that waste-dump failures have on mine operations. Numerous techniques have been proposed for analyzing the stability of embankments subjected to earthquakes. Before choosing an analysis technique, it is worth noting two important differences between the dynamic response of waste embankments and natural slopes. First, waste embankments respond as structures having unique modes of vibration, which causes embankment motions to differ from nearby ground motion. Second, because of embankment response, accelerations can be different at embankment crests than elsewhere in the structure and occur at frequencies that do not correspond to input ground motion. Because of these factors, embankment response should be calculated prior to slope stability assessment. In this paper several analysis techniques designed to calculate slope stability are evaluated, and conventional pseudostatic techniques are shown to be inappropriate for dynamic considerations. Techniques to calculate dynamic stability should include embankment response, all characteristics of earthquake motion, and roughness along failure planes as input, and should provide a displacement time-history of the slide mass as output. Two techniques satisfy this criterion, and in this paper the LADRS technique is recommended for its versatility and simplicity.

Jan 1, 1985

Jan 1, 1916

By R. E. Hucko

Introduction The principal thrust of the US Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce ash and sulfur content of US coals to levels where the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The coal preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas - coal characterization, beneficiation, and ancillary unit operations.

Jan 1, 1985

Alder, John W., Student, Mass. Inst. of Tech Cambridge, Mass. '38 Allen, Charles F Mines McFarland, Cal. '34 Anderson, Norman John, Student, South Dakota School of Mines Rapid. City, S. D. '32 Ansel, Gerhard, Student, Mass. Inst. of Tech Cambridge, Mass. '34 Arakelian, Haig Mark, Student, Inst. of Tech Cambridge, Mass. '34 Archer, George K., Student, Colorado School of Mines Golden, Colo. '34 Arnot, Paul H. 608 S. Acacia St., Compton, Cal. '31 Asel, Philip R., Student, Colorado School of Mines Golden, Colo. '32 Augenthaler, Robert L., Student, New Mexico School of Mines Socorro, N. M. '32 Augustine, Robert W. Address Wanted. '32. Austin, Robert B., Student, Univ. of Idaho Moscow, Idaho. '34

Jan 1, 1934

By V. N. Mackiw, D. E. Weir, D. J. I. Evans

The world's largest reserves of nickel are found in lateritic ores. Commercial exploitation has been carried out for almost one hundred years; however, none of the plants currently in operation produce pure nickel but rather ferronickel, matte, impure nickel oxide or mixed sulphide precipitate. Over the past decade Sherritt has studied various processes, including the modified reduction roast-ammonia-ammonium carbonate leach process, for the production of pure nickel powder and briquettes from laterites. Nickel can be reduced to the pure elemental form at elevated temperatures and pressures from impure basic nickel carbonate slurries. Several methods were studied in the development of the process for working up the pregnant leach liquor and basic nickel carbonate to produce feed for the aqueous hydrogen reduction step in which pure nickel powder is produced. This paper is concerned only with the laboratory studies using the basic nickel carbonate slurry reduction procedures.

Jan 1, 1973

MANY members of the National Societies died in service overseas during the World War. No memorial to these engineers has been set up but a unique and interesting suggestion has been made. While Edward Dean Adams, Fellow of the American Society of Civil Engineers, and Associate of the Ameri-can Institute of Electrical Engineers, ,vas in Belgium last June as delegate of the National Societies, En-gineering Foundation, and Engineering Societies

Jan 12, 1927

By T. Chen

One of the limitations of the 3-dimensional Lerchs-Grossmann pit optimisation algorithm has been the difficulty in calculating an optimum pit with variable wall slopes. The difficulties have been related to establishing various wall slopes without changing the sizes of the blocks used in the normal computation, but still retaining an optimum solution.

Jan 1, 1977

By Douglas M. Dwosh

Inland Steel Coal Co.'s system of applying a gypsum/fiberglass rib and roof sealant with standard rock dusting equipment will be outlined. The criteria for use included acceptability of results, flexibility of equipment, ease of application, and economics. Material is conveyed dry until the gypsum, fiberglass, and water are combined at the discharge end of the rock dust hose.

Jan 1, 1978

J. K. EVELETH, Anaconda, Montana (Communication to the Secretary): Partly for the reasons which Mr. Jones enumerates, and partly because of the presence of copper in greater or less quantities in so large a proportion of the ores throughout this region, I have also found Marguerite's method the most convenient and satisfactory for the determination of iron. In order to avoid the previous precipitation of the copper with H2S on the separation of the iron by means of ammonia, with the consequent necessity for re-precipitation

Jan 1, 1889

By Wilbur Nelson

Little drilling has been done in Kentucky and Tennessee in 1923, with the exception of the Kettle Creek area on the Kentucky-Tennessee line. Oil prices fluctuated between $2.86 and $1.36 Per bbl. for light oil. The Kentucky production was slightly over 8,000,000 bbl., being 1,000,000 bbl. less than during 1922. Tennessee production was approximately 8500 bbl., being a decrease of 1000 bbl, over. 1922. During 1923, the first producing well was brought in, in Clay County, Tenn. Production in Tennessee will undoubtedly increase considerably in 1924, and Kentucky production will probably increase slightly. THE year 1923 has been a dull period in oil development in Kentucky and Tennessee, with the exception of the Kettle Creek area along the Tennessee-Kentucky line, in Clinton and Cumberland Counties, Kentucky, and Clay County, Tennessee. The price of oil during the year has been so low that wildcatters have shown little interest in drilling. At the beginning of the year, light oil sold for $2.31 per barrel and medium oil for $2.06 per, barrel. Prices increased to the highest point for the year in February, when light oil brought $2.86 per barrel and medium oil, $2.61. In April, prices had declined 35 c. while in May an additional decline of 25 c. went into effect. During June, prices declined 20 c. per barrel; during July, 45 c. per barrel; remained stationary during August and September, and dropped during November and December to the low price of $1.36 per barrel for light and $1.21 for medium oil. At present, an increase of 29 c. has brought the price of light oil up to $1.55, and indications are that the price will continue to increase during the coming months. It can readily be seen that during 1923 the price of oil was such as to prevent any drilling except that necessary to hold leases and to maintain production enough to take care of overhead expenses.

Jan 3, 1924

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By T. Busch, R. A. Dodd

The solubility of hydrogen in pure iron and pure nickel, and of nitrogen in pure iron, has been determined and agrees well with earlier data. Nitrogen is insoluble in pure nickel and cobalt. The solubility of nitrogen in Fe-Ni alloys also confirms earlier- work. The solubility of hydrogen in Fe-Ni alloys increases non-linearly with increase in nickel content, but the solubility of hydrogen in Ni-Co and Fe-Co alloys reaches a minimum at 75 and 50 at. pet, respectively. The solubility of nitrogen in Fe-Co alloys decreases approximately linearly with increase in. cobalt content. Nitrogen is insoluble in Ni-Co alloys. Determined interaction parameters are in good agreement with predictions of Gokcen and Ohlani. THE solubility of hydrogen and nitrogen in liquid iron and iron alloys has been studied by various investigators.'-l' The method of solubility measuremerit due to Sievertsl is usually preferred when the vapor pressures of the liquid components are sufficiently small, but other techniques such as sampling the equilibrated melt and then analyzing by vacuum fusion have been used quite often. Previously reported data on the solubility of hydrogen and nitrogen in ostensibly pure liquid iron are summarized in Table I; certain of the quoted results were obtained by interpolation of the published data. Agreement between the various investigators is only fair, indicative of the experimental difficulties involved in obtaining gas solubility data. The only report found on the solubility of hydrogen in pure nickel is that of Sieverts.2 The solubility of nitrogen in iron-nickel alloys has received some attention, 10, 11 the results indicating that the solubility decreases with increase in nickel content, becoming zero for pure nickel. There is no published information on the solubility of these gases in either pure cobalt or alloys containing cobalt EXPERIMENTAL PROCEDURE Sieverts' method of solubility measurement was used throughout the investigation. The construction of the melting chamber is somewhat different from A. Optical pyrometer F. Alundum cover B. Vycor chamber G. Alumina crucible C. Furnace coils H. Alundum sand D. Glass water jacket I . Alundum thimble E. Chamber support J . Detachable vycor base sealed with de Khotinsky cement

Jan 1, 1961

By T. Egleston

THERE has always been a-theory among those working placer mines that gold is both found " rusty," and becomes so under treatment, by which they mean, not that gold becomes coated with oxide of gold, bat that it is either coated superficially or alloyed with sortie substanee 'which prevents the ,contact with mercury, and thus precludes the possibility of amalgamation. To such conditions of the

Jan 1, 1881

By Edgar A. Scholz, Attilio G. Spat

The rapid worldwide increase in labor costs, prices of goods and services, and the rising tide of economic nationalism do not bode well for the future of mineral exploration and the mining industry. The increasing complexity and difficulty involved in finding economic mineral deposits makes these trends particularly significant. A comparative cost analysis of domestic and foreign exploration projects which developed into mines during the period 1960-74 may be useful in indicating the general nature of exploration expenditures as these trends continue. This analysis is based on a survey of 18 US and Canadian mining companies. Due to the inexact nature of exploration expenditure data, plus the fact that no two mining companies follow the same system of cost allocation, the results of the survey must be considered quite general in character.

Jan 6, 1977

By James A. Todd

Use of AN-FO in underground operations has greatly reduced the cost of primary explosives. AN-FO is also less sensitive than conventional dynamites, and when properly used, is safer. Maximum safety in the use of AN-FO, however, requires an understanding of potential hazards from toxic fumes as well as static electricity developed in pneumatic loading. Safe limits and guides have been established to permit most operations to pneumatically load holes that are bottom primed with electric blasting caps, but the toxic fume hazard is less widely understood. During 1959-1960 Du Pont cooperated with the U.S. Bureau of Mines to study the toxic fumes produced by prilled ammonium nitrate-NO. 2 fuel oil mixtures. The conclusions from this work were that oxygen balanced AN-FO, when thoroughly mixed, well primed and well confined in dry holes, produces no greater amounts of toxic fumes than conventional dynamites rated Class I by the Institute of Makers of Explosives. The study also showed, however, that any deviation from these guides tends to increase significantly the quantity of toxic fumes produced. This work was reported by the Bureau of International Symposium on Mining Research at Rolla, Mo., in February 1961.'

Jan 4, 1963