Search Documents

By John J. Reed

This paper was prepared as a supplement to the general review by Dr. N. G. W. Cook. His analysis of the problem in terms of the strain energy involved in making the excavation is excellent. It will contribute much towards a clearer understanding of rock behavior and control. Several of the practical applications described herein can be directly related to Dr. Cook's theories and conclusions, and are based on the very same principles. CONTROLLED BLASTING IN ROCK EXCAVATION Generally speaking, the natural rock is a relatively strong and competent structural material, if we conserve its inherent good properties and perhaps reinforce its weak spots. The difficulty often lies in blasting out the tunnel or chamber without damaging the walls and roof we wish to have remain afterwards. Much progress has been made in the last five years in better understanding the controlled excavation of rock. The specialized techniques known as smooth wall blasting and presplit blasting have now developed from the status of curiosities of rock excavation to the point where these techniques are specified in contracts drawn up for such rock excavation projects as tunnels, underground pourer houses, etc. These techniques have been well described and discussed in previous publications; there is no need to reiterate here. It might be well to point out that recent research has demonstrated the effect that inherent rock stress may have on presplitting in certain directions. Material can be presplit most readily parallel to the direction of maximum compressive stress, and this may not always be in the direction desired. Inherent rock stress measurements by stress relief over coring, etc., may have important value in deciding how to best presplit proposed excavations. In addition, recent work at the Colorado School of Mines has demonstrated the feasibility of con-

Jan 1, 1967

By Brison Robertson, W. P. Fishel

THE carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. One important phase of this subject is the distribution of carbon between the various elements present. The distribution of carbon between iron and other elements evidently will depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying elements and iron and between the elements themselves. In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds. In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present in a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. EXPERIMENTAL PROCEDURE Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a vacuum, in an induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would complicate the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were cooled in the furnace under a vacuum and were then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (I :4) sulphuric acid, and the complete solubility of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe, was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others 1,2 have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represents the titanium that was united with carbon. The filtrate from the carbide residue contains the portion of the titanium that wasin solid solution in the ferrite. Titanium

Jan 1, 1944

By T. W. Guy

DURING recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years-at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures.

Jan 1, 1931

By R. J. Caro

The Anaconda phosphate plant was put into operation in the fall of 1923. Its present daily operating capacity is approximately 170 tons of treble superphosphate and 16 tons of phosphoric acid analyzing 42 pct P2 O5 and 52 pct P2 Os, respectively. As a result of the continued increased demand for phosphates, Anaconda decided in 1947 to expand the plant's daily output to 270 tons of treble superphosphate and 54 tons of phosphoric acid. The present daily plant intake is 335 tons of wet (footwall) phosphate rock analyzing 31.7 pct P² O5 and 0.28 pct V² O5. The rock is shipped from Anaconda's mine at Conda, Idaho, in open railroad cars, having been crushed to pass 3/8 in. mesh at the mine.' The expansion program will require an increased intake of 300 tons of rock per day. The hanging-wall rock anaIj-ses approximately 30.5 pct P2 O5 and 0.11 pct V² O5, and will be beneficiated in a new washing plant under construction

Jan 1, 1950

By W. H. Tuttle, H. R. Ahlquist, A. J. Carlson

Variations of the EVOP technique are accepted as the foun- dation in the development of Erie Mining Company's mining, concentrating and pelletizing complex at Hoyt Lakes, Minnesota. The basic one-variable- at-a-time technique served its purpose through the laboratory pilot plant as well as the full-scale production sized pilot plant. However, recognition by Erie Mining Company management of the potential of computer application and statistical experimentation in plant operation and testing led to acquisition of an IBM 1620 computer in 1961. Adaptation of established techniques in statistically designed experimentation and analysis of results is presented in actual case form including the following: 1. Determination and use of variance, standard deviation, standard errors; application of t-test in determining true differences between daily aver ages of product assays; formulation of quality control limits; determining sample size; and application of normality tests will be discussed. 2. Use of mathematical modeling and regression analysis for establishing mill storage conditions based on bin level indicator lights. 3. Polyvariable random balance design of a balling circuit test and resultant identification of primary control variables.

Jan 1, 1969

By M. S. Burton, H. H. Kranzlein, G. V. Smith

The influence of up to 2 at. pct of Ni and Pt on the yield strength of mono- and polycrystalline high-purity iron has been evaluated at temperatures from + 25° to -196°C. Current theories of solid -solution strengthening fail to explain the experimental observations. The temperature dependence of yield stress was found to be less in the alloys than that in high-purity iron. The room-temperature yield stress increased with alloy content, but at —78°C the yield strength first decreased with increasing a1loy content. AS a result of many studies, a number of theories have been proposed for solid-solution strengthening. The purpose of the present study was to evaluate these theories, as applied to the solid-solution strengthening observed in Fe-Ni and Fe-Pt alloys. Of various theories of solid-solution strengthening, those of Cottrell,1,2 Fisher,3 Suzuki,4 and Mott and Nabarro5 are most prominent, and have been discussed widely in the literature.'-' Of the recent concepts of solid-solution hardening the work of Fleischer9 is notable. Each of these models has been applied to particular alloy systems with some success, but in general none has proved generally applicable. In many of the previous studies to assess the effects of alloy additions in ferrous systems, lack of adequate control of the purity and grain size of the materials has obscured strengthening effects, so that few comprehensive data relating composition, temperature, and change of lattice parameter have been determined. In the present investigation an attempt was made to obtain data which would be meaningful in evaluating the theories of strengthening. Materials of high purity were used to minimize extraneous impurity effects, and both single crystals and polycrystalline materials were studied to evaluate the effect of grain boundaries. Nickel and platinum were chosen as alloy additions, because both belong to the same chemical group and have the same crystal structure and valence, with markedly different atomic diameters. It appeared that some conclusions regarding atomic size effect on strengthening might be made. MATERIALS AND PROCEDURES Fe-Ni and Fe-Pt alloys containing 0.5, 1.0, 1.5, and 2.0 at. pct alloy additions were prepared from high-purity materials. The iron was supplied by the American Iron and Steel Institute from a stock of 99.98 pct zone-refined iron prepared by Battelle Memorial Institute. The minimum purity of the nickel and platinum used for alloying was 99.98 and 99.999 pct, respectively. Alloys were prepared by levitation melting, cast into cylindrical copper molds, and cooled, all under a partial pressure (0.3 atm) of purified helium. Samples were 0.375 in. in diameter and weighed 20 to 25 g. Chemical analyses of the alloys are given in Table I. A sample of unalloyed iron also was cast as a control specimen.

Jan 1, 1965

By John F. Abel

AIME is closing the books on its first 100 years. In the next year the meetings and many papers will doubtless be filled with statistics on the growth of AIME, and, incidentally, on the mining industry. Let's try to keep our cool and avoid breaking our arms patting ourselves on the back. AIME, nationally and locally, runs on the drive and dynamism of a rather small number of its members. If you look at the annual SME Blue Book of national officers and committee members, you will be struck by the repetition of the same names throughout. Trend for a few men to shoulder the burdens and responsibilities can be seen on the local level, too.

Jan 1, 1970

By H. C. Rogers, B. W. Roberts

Vanadium foils and wires, either cold-worked or recrystallized, show a ductile-brittle-ductile fracture sequence with temperature. At about 150°C the hydrogenated vanadium wires are found to be ductile. At room temperature the wires show brittle fracture, and at liquid nitrogen temperature the wires are again ductile, although to a lesser extent than found at 150°C. Hydrogenated cold-rolled vanadium foils have been found to fracture in unusually straight lines along the [100] texture directions. The hydrogen content required to show this [loo] texture fracture is limited to a few atomic percent in range. Hydrogen content above this range causes fracture to occur in random directions. PRELIMINARY experiments with hydrogenated vanadium foils indicated that the embrittling effect of the hydrogen on the vanadium, which was severe at room temperature, was reduced at both lower and higher temperatures. In order to investigate more quantitatively the ductility changes with temperature, vanadium wires were tested in tension at three temperatures. The reduction of area was measured and the fractures examined. Specimen Preparation—The material used was kindly supplied by A. U. Seyboltl in the form of M-in. rod. The nominal analysis was: 99.2 pct V assay, 0.2 pct C, 0.01 pct Si, 0.01 pct Fe, 0.015 pct Ca, 0.02 pct O,, 0.01 pct N2, and 0.003 pct H,. The specimens were 0.035-in. diam wires. These were prepared by cold-swaging the supplied rod to the final diameter without intermediate anneal. They were finished with long-bearing dies. The surface was then given a light polishing with 0 emery paper and degreased in trichlorethylene. An X-ray check indicated that the cold-swaged wire had a fairly strong [110] fiber texture. The wires were then recrystallized in vacuum in continuously pumped quartz tubes at two temperatures to give two different grain sizes. One group of wires was given 45 min at 800°C; another, 60 min at 1000°C. The microstructures in Fig. 1 show the wires after they have been electropolished and elec-troetched in 10 pct HCI. After the 800°C anneal, the vanadium grains had a diameter of 1 to 2p and there appeared to be a tendency to elongation in the longitudinal direction. However, the latter may be an etching effect. After the 1000°C anneal, the grains appeared to be equi-axed, but there was a very large spread in grain size, probably due to some impurity segregation in the wire, Fig. 1, right. The grain diameters varied between the limits of 1 to 150p. The small particles shown particularly clearly in Fig. 1, left, are also visible on the polished surface of all samples before etching and are undoubtedly carbides and nitrides of vanadium. An X-ray check indicated these annealed wires had a strong [110} recrystallization fiber texture. The hydrogenation was carried out in an iron retort with dry hydrogen flowing through it, the retort and contents being heated in a tube furnace with a hydrogen atmosphere. The hydrogenation temperature was approximately 500°C. The hydro-genation times chosen were approximately those which would be just enough to cause the vanadium to be brittle at room temperature and thus allow the greatest chance for ductility to occur at the other two temperatures. Part of the fine grained specimens were hydrogenated for 21/2 min at 490°C. Part of the coarse grained specimens were hydro-genated for 11/2 min at 515°C.

Jan 1, 1957

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953

CHARLES SCHUCHERT,* New Haven, Conn. (written discussion?).- I embrace ace the opportunity to take part in a discussion of Mr. Woodruff's paper because a successful discerning of what actually constitutes pet-roliferous areas from the geologists' standpoint is worthy of our endeavors, not only from the intellectual side, but also because it may lead, as Mr. Woodruff hopes, to the more certain establishment of principles that can be applied to other continents in exploiting them for petroleum. This discussion will also embrace the results of two other recent papers, one by Alexander W. McCoy and one by Maurice G. Mehl.1 Sources of Petroleum.-Mr. Woodruff is agreed that petroleum comes from plants and animals, or possibly from both, and that it has ac-cumulated by migration into reservoir rocks. These reservoir rocks must of course be porous to become catch basins for the oil and gas, and then, too, their present structures are variable, as they occur in anticlines, domes, terraces, etc. , The structures, he states, are more widespread than are the oil pools, and the same is true for the reservoir rocks. Accordingly, there must be many good sands and structures

Jan 11, 1919

By Robert W. Hunt

Delays in the completion of the alterations to the plant at the works of Messrs. Oliver Bros. and Phillips, in Pittsburgh, coupled with the increased demand for metal made from regular Bessemer pig, placing the firm many hundreds of tons behind in their deliveries, prevented Mr. Henry W. Oliver, Jr., from redeeming his promise to place his works at my disposal for further tests of high-phosphorus irons, until May 5th. Upon that date, I assumed charge of the operations in his steel-plant. Mr. Oliver had purchased Neshannock pig as a basis for a supply of phosphorus. My information is to the effect that this iron is made from low-grade Lake Superior ores and mill-cinder, the latter "ore" being utilized to about 40 per cent. of the total mixture. At all events the pig had quite as much phosphorus, and in as varying quantities, as the most exacting could desire. My experiments of last fall had well satisfied me as to the effect of from 0.35 to 0.55 per cent. of phosphorus in the Clapp Griffiths metal. Hence at this time my first trials were directed to

Jan 1, 1886

By Lawrence W. Aldrich

At the San Francisco meeting of the Institute last year, I presented, through the courtesy of Dr. James Douglas, some results of experiments on the roasting and leaching of concentrator tailings. After it became apparent that flotation rather than leaching was clearly the better method of handling the particular problem under consideration, before dismantling the experimental equipment, some data were secured on roasting and leaching the concentrate itself in competition with smelting. Some of the results obtained are given in the following paper and they are of particular interest at this time in view of the large quantities of flotation concentrates with their somewhat difficult smelting characteristics now being produced. A complete wet processt consists of roasting and leaching the calcines in dilute sulphuric acid produced from the roaster gases, roasting the residue with salt and leaching with dilute tower liquors (the well-known Longmaid-Henderson process) and recovering the copper, silver and gold by cementation or electrolysis or a combination of both. It is evident, however, that the residue from the first leaching, carrying about 20 per cent. of the copper and all of the silver and gold, can be smelted if preferable. In considering the application of the scheme to individual cases, it must be remembered that freight plays a large part in any reduction process wherein smelting is not conducted at the mouth of the mine, and that it is not practicable today to build small smelting plants for individual operations, The experiments may be grouped under four main heads: Roasting, leaching, chloridizing residue, and recovery of copper from solutions. The products of two concentrators were used: The Nacozari concentrates were the product of a large modern mill not using flotation, the copper mineral being largely chalcopyrite; and the Tyrone concentrates, the product of an experimental mill including flotation, the copper mineral being chiefly chalcocite. Typical analyses are given in Table 1. Fig. 1 shows screen analyses of calcines obtained by dead roasting the

Jan 1, 1917

By H. Jehn

The high-temperature oxidation of Pt metals results' in the formation of volatile oxides. The evaporation of which considerably increases the metal losses in oxygen-containing atmospheres when compared with high-vacuum or inert-atomosphere conditions. The paper describes gravimetric investigations carried out to determine the metal losses of polycrystalline samples of Ru, together with earlier studies on Ir and Pt at oxygen pressures of 10-3 to 1000 mbar and temperatures > 1000 °C. A strong pressure and temperature dependence is noted. Preliminary results of the oxidation of Pd are reported, too (665 mbar 02, 1100-1300 °C). The oxidation mechanism is discussed and the oxidation rates of Ru, Pd, Ir and Pt are compared with those of the other Pt metals Rh and 0s and of refractory metals.

Jan 1, 1984

By N. A. D. Parlee, I. D. Shah

ThIS reports on some work done on the solubility and diffusivity of oxygen in liquid silver. Solubility. Improvements in the measurement of the solubility of oxygen in silver and silver alloys were made because precise data were needed for calculating diffusion coefficients of oxygen in these alloys. The apparatus and the procedure used were similar to those of Parlee and Sacris.' The main improvement was in the temperature-measuring technique. A MV30 mullite protection tube containing a calibrated Pt-Pt, 10 pct Rh thermocouple was inserted in the reaction tube from the top through a vacuum-tight swage-lok fitting. The protection tube was well-immersed in the liquid silver, which was heated by induction. A Leeds and Northrup potentiometer was used in connection with the thermocouple. All runs reported were made at 1 atm. The temperature range investigated varied from 940" to 1200°C. The ternary point in Ag-0 phase diagram2 is at 939°C and 0.32 wt pct O. This point was reinvestigated using the above-described apparatus and was found to be at 939°C and 0.315 wt pct 0. It was determined by observing the sudden evolution of oxygen at this point while the solubility measurements were made. The point was easily reproducible if precautions were taken to keep the liquid silver essentially in equilibrium with oxygen and to lower the temperature very slowly. All of the results of this new solubility investigation are plotted in Fig. 1. They are represented by the "least-squares" line shown in the figure and the following equation for solubility at po2 = 1 atm: log% O =695.4/T - 1.086 This equation differs only slightly from that proposed by Parlee and sacrisl and that of Diaz, Masson, and Richardson.3 The points of Parlee and Sacris, using an optical pyrometer, are shown for comparison.

Jan 1, 1968

By Alphonse Hennin

It is well known that under certain conditions ammonia is found in the gas produced by the distillation of coal. Until recently it was held, and many still believe, that this ammonia exists in the coal, and is a natural product of the destructive distillation, varying in percentage, like the other products, according to the nature of the coal, but not formed synthetically beyond that limit. This opinion is in contradiction with well-established facts concerning the formation of ammonia from the elements of the coal. If any ammonia exists as such in the coal, the quantity is insignificant. The purpose of this paper is to explain the theory of the formation of ammonia during distillation, and call the attention of the members of the Institute to its application in connection with the production of heating-gas for metallurgical purposes, etc. For many years little or no importance was attached to the presence of ammonia in coal-gas. It was deemed by the gas-manufacturers an undesirable product of the process, as one of the impurities to be removed; and no attempt was made for its recovery. Not until its practical extraction and utilization was found possible, did scientists commence to investigate the question. Little was known about the nitrogen of the coal, and still less about the reactions leading to its transformation into ammonia. A. W. Hofmann, I believe, was the first to establish a relation between the percentage of nitrogen in the coal and the proportion of ammonia in the coal-gas. As early as 1863 he pointed out that, in dry distillation, such as is practiced in the manufacture of illuminating-gas, only one-third of the total nitrogen in the coal is liberated, two-thirds remaining in the coke. It is no longer possible to doubt that the ammonia is a synthetical product, resulting, under certain conditions, from the combination of the,elements of the coal. Chemistry teaches that ammonia is formed in many cases when

Jan 1, 1893

By M. E. Herrera

The use and effectiveness of sealants in under-ground mines is a recognized and well accepted practice by many people in the mining industry. Their use however in many cases is to correct, or attempt to correct, problems that might have been avoided with sealant use in the early stages of development, and continued thereafter.

Jan 1, 1982

By E. G. Leonardon, Sherwin F. Kelly

The first to appreciate and foresee the value of applying electrical measurements to structural studies was Prof. Conrad Schlumberger, Professor of Physics at the School of Mines in Paris. One of his earliest practical undertakings in this line was carried out, in the field, at Fierville-la-Campagne, Normandy, in 1912. His book, published in 1920, still stands as an authoritative, fundamental treatise on the use of the electric current in geological studies, in spite of the rapid evolution of geophysics during the last seven years. A remarkable feature of this book is that, even then, it stressed the role of electricity in structural investigations and made public the first successful results obtained therewith. Stratigraphic studies have been pursued continuously by Conrad Schlumberger and his associates since 1912, the only interruption being the World War. The results attained demonstrate the wide possibilities of electrical exploration in structural work. This field of activity is, at the least, as varied and valuable as the search for ore. It is curious that until very recently it has so slightly attracted the attention of geophysicists and geologists on this continent. The purpose of this paper is to present briefly some examples of the practical application of the potential methods to geological studies. These examples are chosen from a number of problems solved in the field by our firm, in the course of its consulting practice. Certain fundamental points are briefly stated before the field operstions and interpretations are described. Conductivities of the Rocks Compared with metallic substances, rocks are poor conductors. However, it would be a grave error to affirm that they are completely insulating and that no electrical current can flow through them. It is surprising to encounter, even now, in certain discussions about the applicability of the potential methods, deductions based on this assumption that rocks are absolutely nonconductive.

Jan 1, 1929

By C. J. Wilhem, J. M. Devine

A corrosion-testing apparatus which operates in the field and which will determine the comparative resistance of various ferrous materials to corrosion by gaseous hydrogen sulfide at ordinary temperatures is described. The principle of the uniform method of testing is to allow natural gas containing hydrogen sulfide, direct from its source in the field, to flow over the group of specimens for a given period of time, and subsequently to estimate the corrosion sustained by each specimen by determining its loss in weight. The comparative results obtained when specimens of 47 representative ferrous materials of described typical composition \\ere tested at ordinary temperatures with natural gas containing hydrogen sulfide are given in tables showing average penetration of metal, Inches per year. The primary purpose of the work Mas to determine the possible utllity to the petroleum and natural gas industries of ferrous materials that are commercially available, and no attempt is made to discuss the results of the tests from the metallurgical standpoint. The following is a summary of the results obtained: 1. Steels containing 12 to 27 per cent of chromium showed the highest resistance to corrosion. The presence of nickel In these high-chromium steels did not affect their resistance. 2. Steels containing approximately 5 per cent of chromium showed comparatively high resistance, but somewhat less than that of the high-chromium steels.

Jan 1, 1934

Few people in the industry today are competent to comment on the O.G. system for vessel covers, but with papers as well prepared as Mr. Bradley's we will soon be well informed. I would like to direct these comments to Mr. Klaes of Ford Motor Company. Mr. Klaes' description of their steaming hood agrees with our experience at Weirton. We have been able to stay within design limits and, as a result, have had few problems with our auxiliary equipment. Our main problem, as with Ford, has been thinning of our vessel cover tubes. At Weirton, controlled circulation, high pressure boilers are in use as heat recovery units above the BOP vessels. The boilers are provided with "off cycle' oil firing equipment. A Venturi type wet gas scrubber follows the boiler to complete the vessel draft system.

Jan 1, 1972

By Byron W. Cheever

In working up the process which I described at the Chicago Meeting, May, 1884 (p. 163 of the present volume), for the estimation of phosphorus in iron and steel, I employed samples of steel obtained from one works only, and of a given brand. Since then I have had frequent occasion to test the process on other steels, and find that it works equally well. But some steels present certain colors which may mislead the operator; and I therefore propose a slight change in the directions formerly given. On the second page of my paper, in the second paragraph, I would substitute the following modified directions: Place the flask under the hydrant, till the solution is perfectly cold ; then add, gradually, strong ammonia, with constant stirring, till the solution is changed into a pasty mass and the ammonia is in slight excess; then add cautiously HNO3 (1.40 specific gravity)

Jan 1, 1885