Search Documents

By E. V. Potter, H. C. Lukens

In general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation1 the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. Apparatus The apparatus used in these investigations is essentially the same as that used in the manganese work1 and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in gas volume are measured by volume gauge C which is essentially another mercury manometer in which the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 60 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. Method The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient tirne intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1949

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

By William Meyer

DURING the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have, been developed from the crude methods and apparatus of wartime to a science upon which exact engineer-ing calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1936

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

By A. Tremari, Paul I. Eimon

Photogrammetrists are studying with new interest the problems of mine mapping and mining engineers are beginning to see what photogrammetry can do for them. Administrators in a number of European and U. S. mines have tried photogram- metric methods and are finding that better maps and data, needed for mine development, can be produced with savings of time, men, and money. In addition to wide use in small scale mapping projects, photogrammetric methods are now used for producing large scale plans and maps in German coal and lignite mines, in some U. S. open pit mines, to inventory TVA coal stock piles, and to compute highway excavation volumes. In each case surveying and map compilation has been made more efficient and accurate by photogrammetry and at significant savings over ground methods.

Jan 5, 1959

By Alec M. Crowell, Harry P. McClintock

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By Harry P. McClintock, Alec M. Crowell

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By K. M. Busen, J. Lindmayer

A heterojunction model is suggested for descrihzng the electronic conditions at oxide -semiconductor interfaces. Detailed study of the silicon oxide-silicon interface shows that the heterojunction model explains many experimental facts; however, it is necessary to assume that a transition layer exists at the interface. It will he demonstrated that ionic contrbution way also he present. Extended low-temperature heating stabilizes the oxide to a charge carrier density in the order of 10' cln-: determined by the heterojuncton model. OXIDIZED semiconductor surfaces are widely used, since they offer technological advantages and "passivate" the surfaces of semiconductor devices. However, it has been recognized that there are always n-type inversion layers formed in the silicon oxide-silicon system, which must be regarded as a definite disadvantage. An added complication is the "instability" of these inversion layers;' the inversion layer appears to vary with the processing and they change at temperatures as low as 100" to 200°C This paper will point out that the inversion layer is a result of the dissimilarity of the contacting materials and therefore must always be present. The dissimilarity is the essence of the heterojunction or electronic model and involves directly the structure of the materials involved. In addition, one finds the contribution from ions; this disturbance, however. can be eliminated for the case of silicon oxide-silicon interface. The strength of the inversion layer or channel will be expressed in terms of the density of elementary charges per square centimeter, N*, maintaining the channel. The next section contains the formulation of the heterojunction model by assuming a contact between two homogeneous materials. This calculation should not imply that silicon oxide is homogeneous; it serves only to point out the general properties of the electronic model. Following the electronic model, the practical case of the silicon oxide-silicon interface will be discussed. I) THE HETEROJUNCTION MODEL Contacting an oxide with a semiconductor, a work-function difference must be accommodated. Fig. 1 represents the oxide and the semiconductor before and after contact. When the contact has been made, one finds that qVi + qV, = A@; i.e., the work-function difference is distributed between the oxide and the semiconductor. Normally, the work-function difference appears on the wide-bandgap material, but in the present case the oxide is thin and far from being a single crystal. Accordingly, a significant fraction of the work-function difference must appear on the semiconductor. The work function of silicon2 is about 4.8 ev, but we shall not assign any particular work function for the oxide as it may vary. However, oxides usually have lower work functions and therefore the potentials must build up in the manner shown in Fig. 1. Such an argument predicts that the inversion layer must be n type, as opposed to the clean surface which is p type. Another important factor to be considered is that the oxide is disorderly and therefore contains many trapping levels. As a result, the charges in the oxide arise primarily from the change in trap occupation, while on the semiconductor side the space charge is composed of mobile free electrons. The consequence of this fact is that a change to another thermal equilibrium will require some time, dictated by the traps in the oxide. The conditions can easily be calculated on the semiconductor side. Assuming an intrinsic semiconductor, Poisson's equation is

Jan 1, 1965

By T. S. Lovering

An economic geologist is concerned primarily with finding deposits of economic value, estimating their tenor and quantity, their shape and position. Thus the primary problems can largely be lumped under three headings: position, character and quantity; and all three are phases of the broader problem of genesis. Distribution, tenor and quantity are of immediate practical importance and are studied constantly by all who exploit mineral deposits. Although the emphasis changes from year to year, the problems of genesis seem more remote and rarely get the serious consideration from the field man that the other three do. Our understanding of the problems of the genesis of mineral deposits has come largely as a by-product of more evidently utilitarian work in the past, and probably will continue to grow in the same manner lor many years to come. However, it might be economically fruitful for the producers to have many competent investigators spending their time chiefly on the problems of genesis of mineral deposits. Many years ago, when first engaged in work for the United States Geological Survey in Colorado, I expressed a conviction which was just then dawning on me by saying that economic geology was turning out to be 80 per cent structural geology, to which Mr. B. S. Butler replied, "Yes, and more than 80 per cent of structural geology is lithology." At the present time there seems to be a widespread feeling among economic geologists that the problems of position or distribution are largely problems of structure and rock types. Types of Research Ptesearch in any branch of geology can be conveniently divided into two types: field research and laboratory research. Ideas are usually dug up in the field, pruned or developed in the laboratory, and taken back to the field for proving. For either the first or last step the field data should he as complete as possible, and the structural geology of nearly all our mineral deposits still needs more detailed delineation. In general, this means mapping on larger seales. Ideally the structural map should give a factual picture of a11 visible effects of stress; there is still room for vast improvement in the technique of presentation. Information that is much

Jan 1, 1940

By Robert Craig, Earl L. Rau

Introduction Grinding circuits are used to reduce the particle size of ores to the size desired for beneficiation or to grind a concentrate to a size required for final marketing. Grinding and classification can be carried out using either wet or dry circuits. Most sulfide ores are ground in wet circuits using one or more stages of grinding to obtain the necessary mineral liberation to produce a final concentrate which will meet the desired criteria. Iron ores are ground in circuits applicable to the particular ore using either wet or dry grinding. Nonmetallic minerals frequently present different requirements. Barite is likely to be subjected to wet grinding before beneficiating the ore; the concentrate is dried and then dry ground to meet market particle size requirements. The one thing that most mill operators will agree to is that there is no such thing as the "best" configuration of equipment for grinding. The circuit which works well on one ore may be totally unsatisfactory for another ore body. The general trend in the industry is flow sheet simplication with fewer parallel circuits instead of multiple-line circuits using small mills. This change in philosophy has been brought about by the saving of both capital and operating costs that may be possible with larger equipment. Remember that comminution is basically a very inefficient process, and that the costs can range upwards to 50% of the total milling costs. It, therefore, behooves the mill operator to carefully design his grinding and classification circuits. He must ascertain the optimal economic particle size for beneficiation and then make certain he has achieved the best balance between capital and operating costs to achieve the desired mesh of grind. Equipment Grinding circuits consist of one or more pieces of equipment to grind the solids. Generally, these circuits include one or more grinding mills, classification equipment, and the necessary materials handling equipment such as pumps, pipelines, and conveyors. There are many different types of equipment available which are used to grind and classify ores and minerals. Following is a tabulation of most of the equipment used for wet and/or dry grinding.

Jan 1, 1982

By T. S. Lovering

An economic geologist is concerned primarily with finding deposits of economic value, estimating their tenor and quantity, their shape and position. Thus the primary problems can largely be lumped under three headings: position, character and quantity; and all three are phases of the broader problem of genesis. Distribution, tenor and quantity are of immediate practical importance and are studied constantly by all who exploit mineral deposits. Although the emphasis changes from year to year, the problems of genesis seem more remote and rarely get the serious consideration from the field man that the other three do. Our understanding of the problems of the genesis of mineral deposits has come largely as a by-product of more evidently utilitarian work in the past, and probably will continue to grow in the same manner lor many years to come. However, it might be economically fruitful for the producers to have many competent investigators spending their time chiefly on the problems of genesis of mineral deposits. Many years ago, when first engaged in work for the United States Geological Survey in Colorado, I expressed a conviction which was just then dawning on me by saying that economic geology was turning out to be 80 per cent structural geology, to which Mr. B. S. Butler replied, "Yes, and more than 80 per cent of structural geology is lithology." At the present time there seems to be a widespread feeling among economic geologists that the problems of position or distribution are largely problems of structure and rock types. Types of Research Ptesearch in any branch of geology can be conveniently divided into two types: field research and laboratory research. Ideas are usually dug up in the field, pruned or developed in the laboratory, and taken back to the field for proving. For either the first or last step the field data should he as complete as possible, and the structural geology of nearly all our mineral deposits still needs more detailed delineation. In general, this means mapping on larger seales. Ideally the structural map should give a factual picture of a11 visible effects of stress; there is still room for vast improvement in the technique of presentation. Information that is much

Jan 1, 1940

By I. Zaplatynskyj, G. C. Kuczynski

SINCE the excellent studies of metal powder compaction executed by Kamm, Steinberg, and Wulff, no work on the subject has appeared in the technical literature. Kamm et al. were the first to investigate quantitatively the distribution of density in a powder compact, as a function of pressure, height and diameter of the die, powder particle size, etc. For this purpose they devised a very ingenious method. They inserted a thin lead grid into a die and then filled the die with powder. During cold pressing, the lead grid -moved downward. Due to its deformability it followed closely the downward descent of the adjacent powder. The die was then radiographed and, from the deformations of the grid openings measured on the radiographs, the density in the vicinity of each opening was evaluated. Their findings led them to the conclusion that the friction on the side walls of the die is a major controlling factor of the density distribution inside the cold pressed powder compacts. However, it is difficult to conduct tests similar to those of Kamm, Steinberg, and Wulff in a processing plant laboratory, which usually lacks the necessary expensive radiographic equipment. The purpose of this note is to describe a method which makes it possible to determine the density distribution in green powder compacts with the same accuracy as the lead-grid method but which is far simpler and faster and requires only standard laboratory equipment. Instead of using a lead grid, the hardness at selected points of the sectioned compact is determined. If the relationship between hardness and density is known the density distribution is readily obtained. This relationship is easily found from measuring hardness and densities of thin compacts. In such compacts the density, for all practical purposes, is constant throughout. The method was tested on a Plast nickel powder, grade FlA-A20, kindly supplied by Plast Metals Co. Thin compacts (height to diameter ratio 0.2) were pressed in a single action cylindrica1 die at various pressures. The density of the compacts was determined by weighing and by measuring the height and diameter with a micrometer. Subsequently the Rh hardness was determined. Up to ten readings were taken on each specimen. The difference in hardness readings on each compact was never greater than three corresponding to about 0.1 g per cu cm uncertainty in density. By varying the compaction pressure of the samples, a whole scale of densities was obtained allowing construction of a set of density-hardness calibration curves. To test the method several compacts of different height were pressed under varying pressures. Die walls were always well lubricated. After pressing, the compacts were mounted in bakelite and halved by grinding, and hardness readings taken along the diameters of the specimens. The distance between adjacent indentations was about 2.5 mm. After hardness readings were translated into densities, contour maps of densities of the compacts were prepared. One of them is reproduced in Fig. 1. The areas encompassed by the curves are labeled with numbers representing the density in g per cu cm of those regions. In Fig. 2 the same results are re-plotted to emphasize the radial density changes at various depths. The results thus obtained confirm the findings of Kamm, Steinberg, and Wulff kentioned previously. They are recapitulated here briefly. 1—The densest part of a compact pressed from one side is at the outer circumference at the top and the least dense part at the bottom, at the outer circumference. Figs. 1 and 2 show this clearly. 2—The density near the cylindrical surfaces of the compact decreases uniformly with height from top to bottom. 3—The density variation increases with the height to diameter ratio. References R. Kamm, M. A. Steinberg, and J. Wulff: Trans. AIME (1941) 171,'R. p. 439 ;MetaLs Technology (February 1941). R.p. Kamm, M. A. Steinberg, and J. Wulff: Trans. AlME (1949) 180, 2R.P. 694; MetalS Technology (December 1948).

Jan 1, 1957

By Bernard Amadei, Richard E. Goodman

A medium is anisotropic if its properties vary with direction. This is the general characteristic of many rocks, for example, schists, slates, gneisses, phyllites and other metamorphic rocks. Bedded and regularly jointed rocks also display anisotropic behavior. This paper is concerned with the influence of rock anisotropy on in-situ stress measurements. It is limited to stress measurements by overcoring techniques for which strains and displacements are recorded either on the walls of a pilot hole at the end of one or several boreholes or within instrumented solid or hollow inclusions perfectly bonded to the surface of the pilot hole. The rock is described as homogeneous, continuous, anisotropic and linearly elastic. The following questions are answered with special emphasis on rocks that can be classed as transversely isotropic or orthotropic: the number of independent measurements obtainable in a single borehole; the number of boreholes required to determine the in-situ stress field; the influence of rock anisotropy on these numbers; the influence of the anisotropy type and the error involved by neglecting rock anisotropy.

Jan 1, 1982

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mineral Economics Division Mineral Industry Education Division Mining, Geology and Geophysics Division MINING BRANCH AND DIVISIONS OFFICERS AND COMMITTEES Council Ralph E Kirk, '55, Chairman (Coal). C M Cooley, Secretary, M D Cooper, '56 (Coal), Harold Bannennan. '55 (Ind Min Div ). R C Stephenson, '56 (Ind Min Div ) , E P Pfleider, '55 (MGGD) . J D Forrester. '56 (MGGD) , Donald W Scott, '55 (MBD). S D Michaelson, '56 (MBD). J K Richardson (MED). J R Van Pelt, Jr (MIED) COAL DIVISION Established as a Division September 20, 1929 M D Cooper. Chairman H F Yancey, Chairman-elect David R Mitchell, Secretary-Treasurer Professor of Mining The Pennsylvania State University State College. Pennsylvania

Jan 1, 1954

By Harold B. Foxhall

THIRTY per cent of the mineral wealth of the United States is obtained from seven states: Arkansas, Kansas, Louisiana, Missouri, New Mexico, Oklahoma, and Texas. This area, which produced 84,727,156,000 worth of minerals in 1948, constitutes an almost complete economic unit in relation to mineral resources essential to industry. All of these states are producers of fuels and some of metallics, but in the field of important nonmetallic industrial minerals the picture is near perfection-a mineral any one of the seven states lacks, one of the others has in quantity.

Jan 5, 1951

THE first award of the James Douglas gold medal for achievement in non-ferrous metallurgy was made to Frederick Laist, of the Anaconda Copper Mining Co., and the presentation ceremony was a feature of the annual banquet of the Institute at the Waldorf, on Feb. 21. Frederick Laist was born in Cincinnati, Ohio, Oct. 30, 1878. In his early youth his parents moved to California where, in 1901, Mr. Laist graduated from the University of California, in the course of chemical en-gineering. For one year after graduation he was an in-structor in chemistry at the University of Utah. Fol-lowing this he was employed as a chemist in the lab-oratory of the Washoe Reduction Works of the Anaconda Copper Mining Co., where in successive stages he has occupied the position of chief chemist, blast-furnace superintend-ent, assistant superintend-ent of the entire plant, superintendent, and finally manager of the Anaconda company's reduction plants in Montana, which position he now holds. Mr. Laist, in his labora-tory work, manifested great interest in the hydrometal-lurgy of copper and zinc. As chief chemist at Anaconda, he brought the laboratory to a high degree of efficiency.

Jan 3, 1923

By S. C. Miller, R. D. Carter, H. G. Riley

A merhod based on theoretical considerations is presented for estimating srabilized performance of gas wells from data obtained from short-term flow tests. Calculated results are presented for II gas wells evaluated with four-to five-hour flow tests. For seven wells on which comparison war available, satisfactory agreement between measured and calculated performance was obfained. Although the final results are favorable, diflerences in flow capacity k,h obtained from flow tests conducted at different rates were observed. This inconsistency did not seriously affect the calculated results in the test wells. INTRODUCTION In order to negotiate the sale of gas from newly drilled gas wells and to plan otherwise for the orderly exploitation of gas reserves, it is necessary to predict the long-term withdrawal rates physically possible for each well. Since low permeability gas wells do not stabilize except after a lengthy period of flow, the operator is unable, without wasting large amounts of gas, to measure directly the stabilized performance prior to contracting for sale of the gas and connecting the well to a pipeline. This problem is not new, but is one which has recently received considerable attention because of the rising importance of natural gas in the economy and new emphasis on the development of gas reserves. Thus, a method is needed for estimating stabilized performance from information obtained from short-flow tests in which stabilized flow is not attained. Such short tests would be suitable for wells not connected to a pipeline since the tests require only small amounts of time, labor and production of gas. Other requirements of such a method are short calculation time and use of a model of the gas well and its reservoir drainage area which is as consistent as possible with present theoretical, experimental and field knowledge. The method presented herein was developed in an effort to meet these requirements. It has been named the "two-Row method". In addition to the section on the evelopment and description of the method, a description of field application of the method and a discussion of well test results are in- cluded. Finally, there is a section on an additional consideration prompted by some of the test results. The Appendix contains certain details of the derivation of the two-flow method and a sample calculation for Test Well 1. MATHEMATICAL DEVELOPMENT AND DESCRIPTION OF THE METHOD The method is based upon the following assumptions: (1) The system can be described as a finite cylindrical gas reservoir produced by a single cylindrical well located at the center of the reservoir. Flow is strictly radial. (2) Flow obeys Darcy's law except very near the well where a quadratic flow law is assumed. (3) The system is also characterized by a laminar flow skin factor. The use of a quadratic or turbulent flow term is more fully justified in Refs. 1 and 2. When such a system is opened at the wellbore to constant rate flow from an initial condition of uniform pressure distribution, the radius or drainage quickly passes through the non-Darcy flow and "skin effect" region imrnediately surrounding the well. After the drainage radius or "transient" has passed beyond this region and before it reaches the external boundary, drawdown can be expressed by'." After the drainage radius reaches the external boundary, stabilized flow exists and drawdown is given by'," Eqs. 1 and 2 form the basis for the method. The validity of these equations will now be examined in the light of some well test data previously available. It has been found by actual measurements on gas wells that the relationship between drawdown and flow rate, that is the performance curve, is closely approximated by' Eq. 3 is a straight line on log-log graph paper. Eq. 2 and, for any lixed value of time, Eq. 1 plot as a curve which is slightly concave upward on log-log graph