Search Documents

By A. S. Appleton

The diffusion of carbon in Fe-Co-C austenites was studied as a function of cobalt concentration up to 12 at. pet, using an autoradiographic technique. The diffusion coefficient was found to initially decrease and then increase with increasing cobalt concentration, the trends being more marked the higher the temperature of diffusion. These effects were paralleled by variations in the activation energy and the constant for diffusion which, however, were found to be dependent also on the carbon content. The results are compared with the previously available data and their significance is discussed in terms of the kinetics of solid-state reactions in this systern. THE influence of cobalt on the diffusivity of carbon in austenite was first studied by Smoluchowski,' his data being that most commonly cited in works

Jan 1, 1964

By Floyd Kelley

THERE is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the .high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensation of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is, little gained by using specially purified gas, because it becomes contaminated after reaching the furnace.

Jan 1, 1931

The following rules, upon approval by the Board of Directors, shall serve as guides in the practical applications of the Bylaws for the operation of the Institute and have the full power and effect of Bylaws, however, these rules may be changed, modified, re¬pealed or amended when deemed necessary by the Board of Directors Any change or alteration of these Rules shall be published in the Journals of the Institute within three months after such alteration is adopted ARTICLE I-ORGANIZATIONS OF THE INSTITUTE Section 1-Societies Rule 1-Governing Body Each Society shall form its own governing body composed of an Executive Committee, or similarly designated executive body, duly elected officers, and a Nominating Committee for the nomination of Institute officers as provided by the Bylaws of AIME and of each Society approved by the Board In all correspondence and printed matter the Society Boards of Directors shall be specifically identified For ex¬ample, the Mining Board of Directors or the Board of Directors of the Society of Mining Engineers Using simply the "Board of Directors" could cause confusion

Jan 1, 1960

By A. A. Dor

Of the numerous methods that have been tested or considered for the beneficiation of low-grade iron ores, this article deals only with proven flowsheets that are adopted in plants in operation or which have been reliably pilot-plant tested. Several recommended layouts are described and discussed. They illustrate recent trends and embody improvements and new features that have resulted from the experience acquired in the operation of the plants already in service. They have been developed, in the last few years, in the course of designing several iron ore beneficiation plants of various types and sizes. Some of the design features in the layouts which are submitted represent, in some respects, personal views and may not meet the full approval of others in this field. It is hoped that this presentation will provide an opportunity for constructive discussion of the problems involved and of suitable solutions.

Jan 6, 1962

W. VAN DER GRACHT, Tulsa, Okla. (written discussion.*).-I fully agree with Mr. Daly's observation that there is such a coincidence between petroleum deposits and geosynclines as to suggest them to be "closely allied phenomena." However, I accept no "identity of cause." To me the explanation is a simple one. Geosynclinal deposition is the first phase in the formation of a mountain, chain, and petroliferous deposits are indeed closely allied to zones of, mountain folding. In fact, petroleum is a typical occurrence in those beds, which represent the flysch facies, to use the Swiss expression. The uplifting of a great mountain chain is a very slow process; it gradually sets ill as a slow geo-anticlinal upheaval within a zone off former geo-

Jan 1, 1918

By R. Maddin, R. Pond

THERE have been many recent studies of nonequi-librium alloy structures using specimens which have been formed by rapid solidification.' The general methods for achieving nonequilibrium structure utilize high velocity impingement of a liquid metallic droplet(s) and one or more substrates of relatively high heat conductivity. Specimens formed by current popular techniques are small and have various forms of irregular geometry which severely limit their use for many measurements of physical or mechanical properties. As a result of geometric limitations most research has been restricted to X-ray diffraction, electron microscopy, and to a small degree, electrical resistivity. Recently several attempts in mechanical property evaluation have been reported.2,3 A technique for casting large quantities of regular, rectilinear, continuous metallic fibers has existed for a number of years.4 We have utilized this technique with some slight modifications to produce nonequi- librium alloy structures. The apparatus is composed of a small open tube furnace, a pneumatic cage which raises and lowers a graphite ejection mold, and a

Jan 1, 1970

PROGRESS IN DRILLING tungsten-carbide bits, lighter pneumatic drills, bonus plans, and alloy steels are discussed at northwestern gathering.

Jan 3, 1951

Jan 1, 1957

By G. R. Palmer

The occurrence of mercury minerals in precious metal-bearing ores has long been noted. During cyanide leaching of these gold-silver ores, some mercury forms a soluble cyanide complex, which is present in the pregnant leach solution and passes through the process operations of the cyanidation mill. As a result, mercury is found on the electrowinning cell cathodes, on the stripped carbon before It is volatilized during carbon regeneration, or in theme tailings pond. The U.S. Department of the Interior's Bureau of Mines is examining the effectiveness of two ion-exchange resins to adsorb gold and/or mercury from a cyanide leach solution. The resins, Duolite A-7 and Ionac A-305, were contacted with leach solutions containing varying concentrations of mercury, gold, and silver. The resin A-7 reached a maximum mercury loading of 0.0165 lb Hg/ft3, and A-305 reached a maximum mercury capacity of greater than 0.44 lb Hg/ft3. Adsorption of gold by both A-7 and A-305 is influenced by the presence of additional ions in the solution.

Jan 1, 1984

Jan 1, 1922

Jan 1, 1951

Jan 1, 1951

Jan 1, 1942

Jan 1, 1938

Jan 1, 1908

By E. P. Klier, Volker Weiss, George Sachs

IT has been shown that the isothermal transformation of austenite in a special steel can be modified by isothermal holding in the high subcritical transformation range.' Since this treatment potentially leads to increased hardenability, limited testing has been completed to determine if the stabilization effects observed with this treatment can be used to advantage in the heat-treating of 4340 steel. As an index of the effects of the several austenitizing treatments on the hardenability of the steel, Jominy-type hardenability tests were completed for specimens 2.5 in. in diameter and 8 in. long. Since the steel studied is to be used at strength levels where notch sensitivity is of major concern, notch sensitivity after selected austenitizing treatments has been evaluated by notch tensile tests for several specimen sizes. The steel composition and the austenitizing treatments are given in Table I. The test specimens are presented in Fig. 1. The hardenability data are given in Fig. 2 and the notch tensile properties are presented in Fig. 3. The hardenability of the steel investigated when determined by use of the standard Jominy test specimen2 as high and remained essentially unchanged for the different austenitizing treatments. For the larger test specimen, as has been shown by other investigations," the characteristic hardenability indexes are changed and it becomes possible to isolate austenitizing treatments which promote maximum hardenability. The stepped austenitizing treatment promotes higher hardenability as is indicated in Fig. 2. The evaluation of notch sensitivity for very high strength steels is best accomplished by means of the notch tensile test. The experimental conditions of the test, however, modify the notch strengths measured, and in the present experimentation an effort was made to achieve a limiting notch condition by fixing the notch root radius at 0.001 in. while the specimen diameter was allowed to increase from 0.3 to 1.1 in.* For this root radius the notch strength, 0.3-in.-diam specimen, and this trend differs from that for the larger specimens. At the highest tempering temperatures the 1.1-ip.-diam specimens yield comparable results for the austenitizing treatments compared. However, as the tempering temperature is progressively lowered below 800°F, em-

Jan 1, 1958

By James T. Curry

FACED with processing an increasing volume of raw material through its existing plant, early in 1955 Calaveras Cement Co. of California considered incorporating liquid cyclones in its raw mill grinding circuits. One of many problems was the prospect of handling larger volumes of finished slurry through existing pipelines. Fixed capacities of the mechanical classifiers also placed limits on plant expansion.

Jan 10, 1957

A FACT not generally understood about the Engineering Societies Library on Thirty-ninth Street in New York -in particular, not realized by many of the great indus-tries of the country-is that it is a free public institution. To utilize its valuable facilities one does not have to be a member of the national engineering societies (which shoul-der its financial deficit each year). Anyone, at any place in the world, can use the library. A man in California, or in South America, or in Persia, can write or cable to the Library staff and receive information on the same basis as any engineer living in New York. For example, a few months ago an American mining en-gineer in China needed additional geological information about a district which he was about to explore. He cabled his need to the Engineering Societies Library and the next steamer brought him the data he wanted. A phosphorus company in Alabama wished to obtain a translation from the Norwegian of an article on cement which they had heard about. They wrote to the Engineer-ing Societies Library; the article was located, and a trans-lation made and sent them.

Jan 12, 1927

By Thomas A. Wright

No symposium on die casting could be complete without consideration of the methods of formula and impurity control. No consideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. COMPOSITION Aluminum.-Aluminum die castings are expected to conform to the specifications of the American Society for Testing Materials1† and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven

Jan 1, 1935

By John V. Beall

One Sunday night last month the phone rang and it was George Schenck from Penn State. How would we like to see a big scrap operation, he wanted to know. A few days later we were on the Connecticut turnpike headed for New Haven to visit a large scrap operation, M. Schiavone and Sons. George had a large clam basket in the back which he explained was for collecting trophies. The car shredder, he said, turns out some fancy metal shapes. In fact, they have gained a certain acceptance as objets d’art among George's friends and relatives. He thinks there may be a small, but possibly lucrative secondary market for shredded cars in the art world if the idea is imaginatively promoted. On the way to New Haven we received a briefing on the scrap industry. The scrap business grew from humble beginnings. Mostly it was started by a few immigrant Jews who collected junk in hand- or horse-drawn carts. The fortunate one might even have had a truck. Before proceeding further, we hasten to point out that the word "junk" is strictly taboo among scrap people, who prefer to refer to their industry as the "secondary metals industry."

Jan 1, 1970