Search Documents

By E. Robert Ruhlman

The term potash refers to potassium oxide (K2O), a compound not found in nature or produced by man but used as a basis for comparison of all potassium compounds and now is applied generally to various compounds of potassium used by agriculture and industry. Potassium, the last of the three major plant foods to be used in appreciable quantities by agriculture, was originally produced only from organic materials for chemical uses. The first recorded identification of a mineral source of potassium was in 1797; but, until the discovery in 1839 of the large deposits of soluble potassium salts in Germany and their development in 1860-61, nearly all potassium compounds continued to come from organic sources. With the importance of potash to plant life discovered in 1840 by von Liebig and the production of potash in Germany after 1861, agriculture soon became the major consumer of potash. In 1958 agriculture accounted for about 95 pct of the total potash consumption; the chemical industry used the remaining 5 pct. Mineralogy and Geology Potassium, an important constituent of the earth's crust, occurs in many forms in numerous rocks and minerals, including water solutions, but is not found in its native state. Twenty-five of the more important potash minerals are listed in Table 1. The properties of the five potash minerals most common in Permian salt formations follow: Sylvite is isometric; has a hardness of 2, a specific gravity of 1.98, vitreous luster, and cubic cleavage; and ranges in color from clear to brick red. In taste it is similar to halite but has a sharper taste and a cooling effect on the tongue. It is very plastic under pressure. Langbeinite is isometric; has a hardness of 4, a specific gravity of 2.82, vitreous luster, conchoidal fracture, and no cleavage; and ranges in color from clear to gray. It is taste- [ ] less, somewhat granular, and slowly soluble in water. Polyhalite is triclinic; has a hardness of 3, a specific gravity of 2.77, and dull luster; and

Jan 1, 1960

By John C. Kleiber, George M. Meisel

From time to time since the initial installation of an experimental flotation section in 1940, Permanente Cement Co. has made efforts to beneficiate the low-grade limestone fraction which occurs in its deposits at Permanente, Calif. The encouraging results outlined in this article are the result of Permanente's latest effort. THE PERMANENTE LIMESTONE AND THE REASON FOR ITS BENEFICIATION The Permanente deposit is a sheet of Calera limestone over 700 ft thick lying within the Franciscan sediments of the San Francisco peninsula. Limestone suitable for cement manufacture underlies, overlies, and is interbedded with low-grade limestone and chert. Andesite intrusions are found as a secondary gangue. The limestone is identified as follows:

Jan 3, 1964

By Courtenay de Kalb

The following observations upon onyx-marbles are fragmentary, and may shortly be rendered superfluous by the appearance of a work upon these interesting stones by Prof. George

Jan 1, 1896

By V. H. Wilhelm

The year 1936 was a prosperous one for the oil industry in California. Increases in crude prices were posted in February and March. Re-establishment of voluntary curtailment in February was a factor in holding production at an efficient level throughout the year. Reduction of storage was effected through adherence to curtailment measures, aided by greater demand and smaller average well completions. During the first six years of voluntary curtailment, allotments were increased during the summer season and reduced during the winter season. This year, good results were obtained through a revised system of allocation, by which the California monthly quota was held constant at approximately 540,000 bbl. per day. After a 7-month period of practically unrestricted production (ending in January 1936), numerous operators found that curtailment was still necessary, as California and export market,s were not yet capable of absorbing the state's potential production, which was estimated to be in the neighborhood of 850,000 bbl. per day. Therefore, in February California operators again placed themselves under voluntary curtailment; with the result that state production dropped from around 700,000 bbl. per day in January to a low of 565,000 bbl. per day in April, and increased gradually to around 585,000 bbl. per day for December. Drilling activity during the year increased about 10 per cent over that of the preceding year, although the resultant production per well decreased. Field Discoveries As a result of a very active wildcatting campaign in California, aided by better interpretation of geophysical data, five new oil fields and two new gas fields were discovered. Oil Fields Greeley Field, Kern County.—The Standard Oil Co. added to its list of djscoveries by drilling and completing its K.C.L. No. 11-1 well at a

Jan 1, 1937

By M. J. Taylor

A common method of classifying non-water- impounding mine waste structures is necessary to facilitate professional comnunications within the industry and between representatives of industry and government. Camnon classifications can a1 so he1 p quickly create and maintain a mental picture of the structures being discussed. Three categories for classification presented in this paper include: (1) configuration and location with respect to existing topography. (2) material characteristics of waste, and (3) environmental sensitivity or characteristic; of the disposal area. Configuration and location classification involve terminologies typically utilized for waste dumps over the past several years. General classification categories for non-impounding structures include: (a) valley-fill, (b) cross-valley, (c) side-hill, (d) ridge, and (e) heaped. Material characteristics can govern the location, engineering details, and environmental sensitivity of the waste structure. Material classification includes: (a) hazardous, (b) non-hazardous, (c) inert, (d) fugitive dust susceptible and (e) leachate susceptible. A1 though many characteristics are potentially applicable, this paper will focus on the categories mentioned above. Environmental sensitivity of a waste structure encompasses many objective and subjective evaluations plus many multi-disciplinary considerations. Environmental sensitivity incorporates numerous factors in addition to those highlighted in configuration and location, and material characteristic classifications. A few examples of how this categorization can govern the engineering design and location of waste dumps are provided in this paper. In addition to the verbal descriptions of classifications, a simplified version of the combined classifications with an alphanumeric format and its methodology is discussed in this paper. Surface water controls often govern the classification or vice versa. In order to maintain a non- impounding status, water must be prevented from collecting behind the structures. Depending on material characteristics, water inflow to or over the site can cause significant environmental or human consequences. Finally, the access of water to the waste dumps can play a large role in the degree of environmental sensitivity to the site. This paper provides a framework in which to discuss the other aspects of this conference and also provides insights as to how the framework is based on actual practice.

Jan 1, 1985

By George S. Lockwood

Plans are moving ahead toward the July 1965 start-up date for Kaiser Steel Corp.’s new pelletizing plant at its Eagle Mountain, Calif., iron mine. Capacity will be 2 million long tons of pellets containing 65% Fe. A major portion of the output is scheduled for charging into Japanese blast furnaces as the result of a contract to supply Mitsubishi interests with 10.8 million tons of pellets over a six-year period. Kaiser's concentrating plant at Eagle Mountain plus sintering facilities at Fontana are adequate to meet the requirements of its blast furnaces, which, as a consequence, are not expected to take any substantial quantity of pellets during this period. However, some 200,000 tons of pellets per year is scheduled to be used for the production of special steels and in the open hearths as a substitute for the high-cost ores now being used.

Jan 8, 1964

By Howbert Van Dyne

THE Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two near-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant.

Jan 1, 1930

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. [ ] In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. QUANTITIES AND TREATMENTS OF TREATED TIMBER PURCHASED In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required on their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By Carl E. Swartz

Although a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. Characteristics and Requirements of Solders in General General Physical Properties.—When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.—The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

By E. C. Potter

It is not the purpose of this paper to enter into the minutiae of a subject so vast, upon which volumes have already been written and volumes more might still be written, but simply to pass in review the characteristic features of that practice, which, dating from the blowing-in of the Edgar Thomson "A" furnace in 1879 and continuing down to the present day, has given to American blast-furnace operations a new significance. The blowing-in of " A" furnace marked the beginning of a new era in the science of iron-smelting if, indeed, it was not the very birth of science as applied to this industry in the United States. American blast-furnace practice in its generic sense and world-wide significance dates from that day, and really all that is valuable, all that is remarkable or worthy of discussion, is embraced in the experiences and achievements of the past fifteen years. Back of that we find only the dead level of mediocrity, or worse, a dispoition to " let well enough alone;" a general, almost universal, employment of " rule of thumb " methods. The application of scientific principles and methods was rare and, indeed, previous to the introduction of the Bessemer process in the early seventies, science had no place in controlling the operations of the American blast-furnace. The old practice consisted mainly in dumping raw materials in at the top of the furnace and tapping out iron and slag at the bottom, for the successful consummation of which the furnace-manager directed his best energies toward keeping the furnace as free as possible from "gobbing" with, alas ! but indifferent success. The burdening of the furnace was based largely on Mark Twain's receipt for " Johnny-cake," altered to suit the circumstances, viz.: a lot of ore, a lot of fuel and about a quarter of a lot of flux. The possible capacities of furnace-plants were not nearly realized. Enormous wastes were permitted, unheeded because not understood. In the use of fuel quantum suff. was always the rule. Increase of product was not thought of because it was not deemed wise or safe to attempt

Jan 1, 1894

By Nicholas J. Grant, Chih-Chung Wang

TO phase of the Ti-0 system has the structure of NaCl and has a wide range of solid solubility.' In the course of studying the Ti-Cr-0 ternary system, binary alloys were made of iodide titanium and high purity TiO,. It was found from X-ray studies of the binary alloys that a transformation of the TiO appears to take place at a temperature near 925°C. Evidence of this phase change is best seen in Fig. 1. Fig. 1A shows the X-ray spectrometer pattern (CUKa radiation) of an alloy of 25 wt pct 0 corresponding to the stoichiometric composition of TiO.

Jan 1, 1957

By A. W. Fahrenwald

The function of the c1assifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred to as "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particu1ar method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted. Relation of Classifier Efficiency to Grinding Efficiency The energy of crushing, and therefore the cost, according to Rittinger's Law,l is proportional to the new surface exposed in crushing. Since the new surface produced in crushing is nearly proportional to the reciprocals of the diameters crushed to, it is obvious that the cost of crushing in the finer sizes is tremendously greater than in the coarser sizes for equal ratios of reduction. High circulating load of finished sand in the circuit of the classifier and grinding mill is therefore obviously expensive practice. It is the classifier's function to reduce this to a miniMum.

Jan 1, 1930

By J. H. Nead

The subject of this paper is one to which there are many references in the literature on the manufacture of steel in the open-hearth furnace, but few actual experimental data have been published. For that reason, the presentation of results obtained from two open-hearth heats where attempts were made to measure the sulfur absorption will be of considerable interest and value. The two heats on which the experiments were made were Armco ingot-iron heats and differ from the usual open-hearth heat of medium- or mild-carbon steel in that the refining is carried further; in this product the carbon and manganese are reduced practically to traces. In most other respects, and especially in respect to the absorption of sulfur from the producer gas, the two heats are typical of usual open-hearth practice. The object of the experiments made on the first Armco iron heat was to determine the fluctuation of the composition of the metal bath and the slag throughout the course of the heat, with especial reference to the variations in sulfur. It was hoped to determine whether there was an increase in sulfur in the bath from the producer gas and if so at what stage in the process the increase occurred. The experimental method consisted of charging analyzed scrap and pig iron, so that the sulfur in the charge could be calculated. Then, throughout the duration of the heat, metal and slag samples were takcn every half hour, beginning as soon as there was enough molten metal to take a sample. These samples were analyzed; the results are given in Table 1. All domestic scrap was used and the charge was made up as follows: Head End Finish Pounds Pound Pig iron........................ 36,300 Pig iron....................... 23,900 Sheet scrap bundles............. 36,200 Sheet bars..................... 23,900 Sheet bm..................... 40;200 The total charge, exclusive of the re-pig added near the end of the heat, was 160,500 Ib. The limestone charged was 21,400 Ib., or 13½ per cent.

Jan 1, 1924

THE CHAIRMAN (A. F. Lucas, Washington, D. C.).-Mr. Matteson has stated that the drilling of certain deep wells has proved a failure because they were abandoned too soon. He advises drilling more wells around salt domes, in the hope of finding additional oil sands. I have had some experience on the domes and believe that by drilling shallow wells, one loses time and money. I have advanced the opinion -that by drilling central wells in the -most likely location of a dome, showing is certain weakness, a better result could be obtained. I have in mind one locality where Mr. Knapp drilled a well through the salt¬the only location that I know of on the Gulf Coast where oil was found underneath the salt. Mr. Knapp found a great deal of gas in it. The salt itself was impregnated with oil and gas; and my opinion is that in such instances, instead of drilling so many wells around a dome, if you will attack at a weak point to as great a depth as a drill will go, the results will he much better. At present we have instances where drills have penetrated to 7300 or 7400 ft. in depth. Why couldn't the rich companies that are operating around the Gulf Coast arrange to get some special drilling apparatus and drill with the rotary first for, say, 3000 to 4000 ft., always in the likely location, and then proceed with the cable? I think we need just such work. In Mr. Matteson's paper lie quotes from an author whose writings in the Federal Bulletin and in the Louisiana Bulletins have been quite extensive. He states that oil and asphalt have originally been found on the surface of those domes. I have been over and examined nearly all of those domes (not all of them, because many have been developed in the last few years) and found no such occurrence at the time; and in the old well-known humps or big hills, as they generally called them; I have never found either salines or asphalt or petroleum. In only' one instance it looked as though asphalt night have exuded out of the ground, and that was in the Sour Lake, but right in that neighborhood years previous to that a company had operated commercially-they had a little refinery there-and had found it so unprofitable that they pulled up stakes and quit.

Jan 4, 1918

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1946

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb Corp.'s Tsumeb and Kombat mines. The Kombat mill fiowsheet and metallurgical data are given with particular reference made to the separation techniques using activated carbon. The mine's historical background, geology, and mining methods are described briefly.

Jan 1, 1974

By W. R. Hibbard Jr., T. Michalak

THAT the amount of deformation and annealing time influences the recrystallization temperature of cold-rolled copper has been well established. Evidence that the recrystallization temperature can be affected by the deformation texture has been reported by Brick and Williamson,% ho found that copper straight-cold-rolled to 99 pct reduction to produce one deformation texture and copper cross-cold-rolled to 99 pct reduction to produce a second and different deformation texture correspondingly recrystallized at different temperatures to different textures. The purpose of the present work was to study more thoroughly the effect of the deformation texture on the recrystallization of cold-rolled copper. Experimental Procedure The copper used in this investigation was commercial OFHC copper (nominally 99.985 pct Cu) in the form of 0.500-in. plate. Qualitative spectro-graphic analysis showed only a slight trace of iron and a trace of silver. No analysis was performed to determine the exact content of the iron and silver,

Jan 1, 1958

By Uros Bajzelj

To mine very weak carboniferous schists subjected to high ground pressures the underhand cut-and-fill stoping method was proposed using an artificial plate roof. An experimental stope was mined using three consecutive levels. Rock pressures, deformation of the reinforced concrete plate, and the quality of stowing were evaluated. It was found that roof deformations were minimized if the reinforced concrete plate and uncemented backfill were replaced with cemented backfill containing reinforcement near the bottom. The mining method prevented the occurrence of high rock pressures at the face. The method is suitable for mining subvertical ore bodies with large horizontal areas.

Jan 1, 1984