Search Documents

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Michael J. Messel

THE critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. EXAMINATION OF DEPOSITS In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesiumsilicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1947

By M. H. Richman, E. S. Meieran

An analytical method is presented which enables the electron diffraction patterns from a twinned region to be indexed. The method has only been applied to (112) twins in bcc lattices, but can easily be adapted to other types of twinned lattices. Calculations of all twin spots, including those superimposed on matrix spots, is made possible by this method. SINCE the advent of transmission electron microscopy, the analysis of selected-area electron diffraction patterns has become very important in the interpretation of electron micrographs. Frequently, as in the case of some martensites, twinned areas are observed and give rise to complex diffraction patterns, which so far can be analyzed only for the simplest orientations of the thin foil specimen with respect to the electron beam. In order to simplify the analysis of twin patterns of more complex orientations, an analytical method was devised which is capable of predicting the positions of all reflections from both matrix and twin regions for all possible foil orientations. Although the method has only been applied to the case of bcc metals twinned about a (112) plane, it is equally applicable to other Bravais lattices. This method has been successfully applied to selected-area electron diffraction patterns of Fe-Ni and Fe-Ni-C martensites and drawn tungsten wire. PROCEDURE Imagine the reciprocal lattice corresponding to a bcc material, with each point hkl representing the crystallographic plane (hkl). Since the extinction conditions require that for this lattice, only reflections where h + k + 1 = even integer are allowed, the three dimensional reciprocal lattice is actually fcc. Since in real space twinned regions and matrix regions are mirrored across a (112) plane, the twinned reciprocal lattice is derived from the matrix reciprocal lattice by a rotation of 180 deg about a (112) direction. While it is possible to calculate how a point hkl will shift under a twinning transformation to a new point htktlt using only the reciprocal lattice based on the orthonormal vectors [100], [010], and [001], the calculations are greatly simplified if a new orthonormal coordinate system containing the twin axis is introduced. The twinning operation then becomes a simple rotation of 180 deg about a principal coordinate axis (in this case the twinning axis), and a retransformation back to the original reciprocal space will give the position htktIt of the twinned reflection.

Jan 1, 1963

The Mascot-Jefferson City zinc mining district in eastern Tennessee has been a major zinc producer for over 60 years. The district lies within the Tennessee division of the Appalachian Valley and is underlain by folded and faulted Paleozoic rocks. The local formations are composed of limestones and dolomites with occasional shales, and sand- stones, and thin and scattered chert nodules. The regional structure of the district is unique in that it is complicated by irregular, distorted, and broken anticlines, synclines, domes, and major and minor post-ore folding and faulting.

Jan 5, 1976

By A. E. Belton

The individual projections for large mines in the Pittsburgh coal seam in northern West Virginia are discussed with emphasis on roof control and ventilation requirements. All four mines use continuous miners with panel belts and rail for main line haulage. Both development and retreat-type mining are covered. There are a variety of mining projections being used currently in northern West Virginia. To discuss each would be impossible, so an arbitrary cross section has been selected in an attempt to indicate a fair degree of representation. Four mines, hereinafter referred to as Mines A, B, C and Dl will be discussed separately. The greater part of northern West Virginia coal production is mined from the Pittsburgh seam. This is the seam worked by all the mines discussed here. Although the coal bed outcrops at the eastern and southernmost points, these mines are all working in a depth ranging from 400 to 1400 ft below the surface. Some steep gracles have been encountered but are only considered local in nature; the overall average dip of the seam is 1 1/2 % northwest. In each of the operations the particular mining scheme used has proved advantageous, since they have been designed to satisfy particular equipment and/or physical condition requirements. So regardless whether such projections utilize a partial or full recovery principle, the productivity performances appear better than average. MINE A Full retreat is the basic mining approach for mine A, although current mining is primarily in the entry-driving stages to expand territory in preparation for pillar work. Only one section unit now on retreat. The average clean coal production at this mine is 7000 tons per day. Initially, a ripper-type miner was used for development at this mine. But with a rather weak roof overlying the coal bed and the greater horizontal span left at the top by a ripper machine, roof control became a critical problem. Even though roof bolts were used concurrently in the mining cycle for initial support, the majority of the roof in these entries

Jan 1, 1962

By Charles Pack

Die castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into three groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings. In the machine shown in Fig. 3, patented by Doehler in 1910, compressed air is used for forcing the metal into the die. In Fig. 4 is shown another of this type of machine. Here compressed air is applied to the surface of the molten metal to force it into the die. In a machine patented by Chandler in 1914, shown in Fig. 5, the

Jan 1, 1919

By W. H. Emmons

The exploration of deposits of the metals will never become an exact science. There will always be an element of uncertainty in prospecting and developing mines. In countries where the surface has been closely scrutinized, most of the deposits whose outcrops contain valuable metals have probably been discovered. Many metalliferous deposits, however, are normally so much altered at the surface that the true significance of their outcrops is likely to be obscured. If a deposit is not exposed, its presence may become known by some one of its characteristics that is different in kind or in degree from a similar feature of the associated rock. Thus, a deposit that is not exposed may be discovered because of its magnetic property. So few minerals are strongly magnetic that the value of magnetic surveys is limited, but the dip needle has nevertheless proved of great aid in locating magnetic belts, and these in some regions are associated with workable iron ores. The Cuyuna Iron Range of Minnesota, which does not exhibit any outcrop of iron ore, was discovered by drilling "areas of attraction" that are due to belts of magnetic rocks associated with the iron ores. In some regions the use of the dip needle is justified, even if it does no more than reveal the strike of the rocks, since a knowledge of the latter enables the driller to locate and point his holes to advantage. The measures of gravity by the use of the pendulum are so accurate, or the limit of error is so small, that one might detect the presence of a concealed tabular deposit approximately at the surface, 34 ft. (10.36 m.) thick, having a density double that of the surrounding rocks. However, not many deposits have a density twice that of ordinary rocks and a thickness as great as 34 ft.; if they lie a short distance below the surface the density or the thickness must be even greater. Consequently, there is not much hope of sufficiently developing the gravity method of detecting deposits of heavy ores to make it of practical value. If the limit of error could be reduced to about one-tenth the present factor, and if the rather tedious and painstaking methods of determining gravity that are now in use could be simplified, the method would promise some degree

Jan 1, 1918

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979

By D. G. Osborne

Transportation cost is a key factor in both the profitability and competitiveness of coal marketing. With coal exportation growing rapidly, moisture control is important. Although in some cases, too much moisture reduction can lead to losses in transportation and pollution problems, there is normally justification for reducing moisture by mechanical means as much as possible. This paper reviews current technology of dewatering coal fines and examines the comparative capabilities of screens, filters, and centrifuges. Financial considerations are stated and implications of capital and operating costs on selection are discussed.

Jan 1, 1985

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

COLORADO LOCAL SECTION Executive Committee CHARLES A. CHASE, Chairman S. A. IONIDES, Vice-Chairman C. LORIMER COLBURN, Secretary-Treasure, 614 Ideal Bldg., Denver, Colo. F. H. BOSTWICK, W. G. SWART. The annual meeting of the Colorado Local Section of the Institute was held at the Savoy Hotel, Denver, Jan. 15.- The Chairman, Frank Bulkley, presided and made a short address on the work of the Section. The following officers were elected:

Jan 3, 1915

By AIME AIME

THE 139th meeting of the Institute will be held Feb. 17-20, in the Engineering Societies Building, New York. The annual business meeting will be held on Feb. 18 at 10 a. m., and no technical sessions will be scheduled at that time, so that all members may participate in the election of officers, hear the presentation of the annual reports of officers and committees and discuss any matter which they may care to bring up at that time. The annual dinner will be held at the Conlmodore Hotel on the evening of Feb. 20, and the usual good time is promised. Arrangements for this and other social features of the meeting are, as usual, in hands of the New York Sec- tion, of which the chairman this year, Ralph M. Roosevelt, has a well-established reputation earned as president of the Zinc Institute, as host.

Jan 1, 1930

By C. L. Horn

All the tunneling machines discussed in this chapter are Calweld machines. I have divided the machines designed for soft-to-medium formations into three groups, correlated with typical formations and estimated compressive strengths: 1) Running sand and silt requiring blade cutters. 2) Chalk and clay, requiring drag-type cutters, for compressive strengths ranging from 0 to 2000 psi. 3) Sandstones, hard clays, and limestones, requiring disk cutters, for compressive strengths ranging from 2000 to 20,000 psi. All of the soft-to-medium-formation machines are powered by electric hydraulic or diesel hydraulic pumps. The pumps in turn drive hydraulic motors for the torque reaction. The soft-to-medium-formation machines are enclosed in a 360º shield with a cutting shoe, a center portion of the shield housing the mechanical equipment, and a tail shield. Tunnel supports are usually required, and the supports are normally erected in the tail shield. Our first machine was built in 1963, and all but five of the machines illustrated in the figures with this chapter were built in 1966 and 1967. Some of the machines manufactured will be discussed in the following sections; specific features as development has progressed will be pointed out. HARD-ROCK MACHINE The Calweld hard-rock machine has been designed along basic and accepted principles for a hard-rock mechanical borer. The features of this machine are as follows: 1) Direct electric motor drive through a planetary gear reduction ring and pinion gear, and then to the cutting head through a hollow drive shaft.

Jan 1, 1970

By C. F. Mabery

So far as the elementary composition of petroleum is known, it may be briefly stated. Petroleum consists principally of a few series of hydrocarbons, with admixtures of sulfur, nitrogen, and oxygen derivatives in comparatively minute proportions, which may be regarded as impurities to be removed in the preparation of commercial products. But as each series is represented by many homologs, in the aggregate, crude petroleum is an extremely complex mixture of hydrocarbons and their derivatives. In part, these hydrocarbons individually conform in structure to the system of synthetic hydrocarbons whose structure is well defined and represented by the typical series CnH2n, + 2, C.H2n, the series CnH2n,-2, CnH2,-a, the members of which have not been sufficiently studied to establish their structure, and the series CnHz,e composed of the aromatic group, benzene and its homologs. Hydrocarbons of greater density contained in the portions of petroleum that cannot be distilled without decomposition doubtless have less hydrogen than is represented by these formulas. Since to every hydrocarbon there is a definite temperature, even in vacuum, at which its constituent carbon and hydrogen atoms fall apart, and since for the heavier bodies this temperature is not much above 360" C. in vacuum, it is evident that some other method than distillation must be devised for their separation if anything further is to be learned concerning their individual constitution. Classification of Petroleums There is such a wide variation in the composition of petroleum from Merent fields, it would seem possible to make a classification on this basis were it not that no single variety is entirely free from hydrocarbons contained in others. Such a classification has been suggested of the exceptionally pure Pennsylvania petroleum, the sulfur oil from Trenton limestone and other sources, the California oil with its large amount of nitrogen (quinoline) derivatives, and the Russian oil, composed chiefly of the naphthene hydrocarbons.' A commercial distinction is made

Jan 1, 1921

By A. L. Field

Previous Publications THE first report on the slag viscosity work of the Bureau of Mines was made by one of the authors 1 in 1916. It was concerned chiefly with, the method of measurement. A paper 2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper 3 was communicated to the Faraday Society. Purpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was early observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al203), and silica (Si02), provided the percentage

Jan 12, 1917

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958

By Howard Smith

FOR several years this Institute has recorded in its TRANSACTIONS the various discoveries of potash? in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons with an equivalent of 144,342 tons of pure potash.

Jan 1, 1936

By Lloyal O. Bacon

In the spring of 1952 Calumet and Hecla Inc. began a geophysical program near Shullsburg, Wis., in the Wisconsin-Illinois lead-zinc district, to assist the geological and drilling exploration programs. Sphalerite, the ore mineral in this area, occurs with a considerable amount of marcasite. In general the higher the percentage of sphalerite in the ore, the higher the percentage of marcasite; however, there may be mineralized zones high in marcasite but low in sphalerite. Orebodies in general are relatively narrow and elongated.

Feb 1, 1956