Search Documents

By Samuel M. Cassidy, John A. Garcia

IN some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haul- age and air. On completion of the panel the two entries are sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1937

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By R. A. Hadfield

The present tribute to a great pioneer in the steel industry, with the accompanying remarks upon the town of Sheffield, which has remained to this day what his invention made it, an important center of that industry, originally formed a part of the paper on "Iron Alloys," prepared, at the invitation of the Council of the Institute, for the Chicago meeting of August, 1893. That paper, begun with the intention of dealing with many alloys of iron, became, of necessity, through the limitations of time on the part of the writer and of space in the Transactions of the Institute, mainly a discussion of the principal modern commercial alloy of iron, manganese-steel; and much introductory and general matter was consequently omitted. The Secretary suggested, however, that this particular portion would be interesting and appropriate as a separate contribution, and I therefore present it as such, offering the foregoing statement simply as an explanation of its incomplete character. If I had undertaken to write a paper upon this subject alone, I should have felt myself bound to bestow upon it more elaborate research and to treat it with more abundant details. It was in the immediate neighborhood of Sheffield that the first successful process for the fusion of steel on a commercial scale saw the light. The late Dr. Percy, a leading authority in general metallurgy, says: " Formerly, so far as I am aware, steel was never melted and cast after its production; and in only one instance, viz., that of wootz was it ever molten during its production.....Now, by the fusion and casting of steel after its production its heterogeneousness is remedied, and ingots of the metal may be procured of perfectly uniform composition throughout; and for the practical solution of this important problem we are indebted to Benjamin Huntsman, of Sheffield." As a recent American journal appropriately remarks: " Huntsman's patient efforts, at last rewarded with success, entitle him to an elevated niche among the heroes of industry. The invention of cast-steel was second

Jan 1, 1895

By T. P. Meloy

In a recent paper, Gaudin and Meloy1 derived a size distribution function for single, impact fracture. Mular2 extended the use of this size distribution to describe the output of carefully controlled grinding experiments. As it stands, the function is difficult to compute. Consequently, a series of tables of the function are presented below: where M(x) is the cumulative fraction finer than size x when x is particle size. Weight percents are tabulated for the single parameter, r, in three different size ranges: from 0 to 1, from 1 to 10 and from 10 to 100. Tables I, II and III are cumulative percent finer and Tables IV, V and VI are for weight percent passing screen size x, retained on the screen below. A number of conditions from the table are plotted in Figs. 1 and 2. Fig. 1 is a plot of the cumulative percent finer vs. size, and Fig. 2 is the weight per-

Jan 1, 1963

By G. A. Collins

Being much interested in efficiency-work in general, and an ardent reader of writings on this subject by Frederick W. Taylor and others, as applied to manufacturing-plants, and having served my apprenticeship from mucking to the engineering design of ore-dressing and underground plants, I hope that this paper will lead others to investigate the field more fully, to the improvement of general mine- and mill-operations, as well as the advancement, intellectually, physically, and financially, of the employee and his relations with the employer. If a man who is prepared to look closely and observe broadly starts in Canada and zig-zags from camp to camp to southern Mexico, taking time casually to inspect mines, mills, and smelters, he will be pitifully impressed by the great difference in customs, and the general waste of labor, time, and money throughout the country. He will so seldom observe a dollar's worth of results given in exchange for a dollar spent that he will form a poor opinion of operating-efficiency and management. This highly-scientific department, requiring an amount of skill and executive ability equaled in few, if any, of the professions, certainly falls short of the standard established in our greater manufacturing industries. It is easily said that this is due to the diversity of conditions in mining, milling, and smelting. But on second view it must be admitted that there is room for tremendous improvements in nearly every mining-organization. The proposal of such improvements is often met by the argument that any mine is but a temporary affair, yielding such profits as to make efficiency-work of no consequence; but any business which is profitable and worth doing at all is worth doing on a basis which gives the greatest return on the investment.

Jan 1, 1913

By R. H. Atkinson

With the object of improving the melting, casting, and working of palladium and 95.5 pct Pd-4.5 pct Ru, the effects of different melting atmospheres (reducing, oxidizing, and neutral), crucible linings, and annealing atmospheres have been studied. Some interesting observations are included about the solubility and diffusion of gases in palladium. THE object of the present work was to ascertain the effect of oxidizing, inert, and reducing ambient atmospheres on the melting and casting of palladium and a Pd-Ru alloy commonly used for jewelry. The need for such a study was indicated during World War I1 when jewelers experienced difficulty in their attempts to make small castings of the torch-melted Pd-Ru alloy by the lost-wax process. When the metal was melted under oxidizing conditions similar to those used for platinum, the castings were gassy; on the other hand, if the melting atmosphere was reducing, the castings were hot-torn and brittle. General Experimental Procedure Pure palladium sponge (99.9 pct Pd) and pure ruthenium powder (99.8 pct Ru) were used for making small ingots (50 g) of palladium and 95.5 pct Pd-4.5 pct Ru by induction melting. The coil, 3 in. high by 2 in. ID with 16 turns, was energized by a 20 kva Ajax high frequency converter. The melting crucibles, so-called sand crucibles, which were made of a highly refractory fireclay, were lined with different materials, including proprietary magnesia, alundum, zircon, and zirconia

Jan 1, 1957

By B. D. Crawford, S. A. Falconer

ONE of the outstanding achievements in connection with this country's war efforts has been the ability of our mining industry to supply from domestic sources many of the minerals of strategic importance that formerly were obtained principally from abroad. In order to meet the war-born demands for these scarce minerals, it has frequently been necessary to develop special methods for treating ores and waste products hitherto considered too low-grade to be workable; and to improve the efficiency of older beneficiation processes. Important in this respect have been the recent technological advances in the field of froth flotation of nonsulphide minerals. Because of the refractory nature of many of these domestic ores, and, in many cases, the limited available technical data regarding their treatment, much research work has been necessary. The following examples describe the procedures and reagents used, and the results obtained, in certain laboratory flotation investigations conducted by American Cyanamid Company's engineers at the Cyanamid Ore Dressing Laboratory on ores containing such minerals as scheelite, manganese oxides and carbonate, ilmenite, brookite, kyanite, garnet, spodumene, mica, feldspar, celestite, fluorite, chromite, corundum, and cassiterite. In presenting these data, we wish to point out that many of the minerals listed have previously been tested, and their amenability to flotation reported, by other investigators-notably those of the United States Bureau of Mines. In some instances the procedures and reagents used in the treatment of some of the following described ores follow rather well-established lines, and with one or two exceptions, the reagents used were well known. However, many of the ores tested did not respond well to simple conventional procedures and it was necessary to adopt special methods of conditioning and desliming, reversal of the usual order of floatability of some of the minerals, multiple cleaning, etc., in order to secure separations. Except where otherwise noted, all numbered and trade-marked reagents mentioned in this paper are marketed by the American Cyanamid Co. or the American Cyanamid and Chemical Corporation. TUNGSTEN ORES Tungsten minerals, vitally important in the war industries of the United States, rank high in the list of those we formerly had to import in order to supply our needs. Most of our domestic ores of tungsten contain scheelite as the valuable mineral. Today there are in the neighborhood of twelve tungsten operations in this country where flotation is used as the main or accessory form of benefication. It has, of course, been known for some time that scheelite and other tungsten minerals respond to treatment by flotation.

Jan 1, 1944

By J. Amanat, H. J. Siriwardane

A numerical procedure based on nonlinear finite element analysis has been developed for predicting subsidence profile over longwall mine panels. The developed procedure has been verified by comparing predictions with published field observations at several mine panels. This paper presents certain aspects of predicting subsidence profile over mine panels located in hilly terrain. Analysis of four such cases are presented herein.

Jan 1, 1984

Discussion of the paper of C. W. WASHBURNE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93,. September, 1914, pp. 2365 to 2378. ROSWELL H. JOHNSON, Pittsburgh, Pa.-It seems to me rather important to bear in mind one thing which is sometimes lost sight of, that the marine sedimentary rocks are laid down in water. We have to start with an initial charge of water. That being so, and the surface tension between the water and the -oil being as slight as it is, as referred to by Mr. Washburne,. the phenomena of capillarity are bound to be most important as between the liquid surface and the gas surface. So far as the liquid-gas surface is concerned, capillarity, in my opinion, is of the utmost importance, and it seems to me this paper of Mr. Washburne's is of great value to us for that reason. Starting out as we have, with our attention concentrated upon gravitational sorting, we have had to wait for the discussion of movement furnished by Munn, and this discussion of capillarity by Washburne, for a more balanced view of the situation. It seems to me that in the accumulation of oil and gas we have a problem of the interworking of gravitational sorting, capillarity, viscosity, immiscibility, and movement. All five things seem to me to be important. I would have expected Mr. Washburne to have given a fuller treatment of the relation of movement to capillarity. In my own experiments I find that gravitation and capillarity alone seem remarkably impotent when everything is at rest, but if I furnish a little movement, gravitation and capillarity step in and accomplish a great many results that one would not expect. Take a horizontal tube and fill a portion at the middle with an ordinary sand saturated with oil, and then put water and sand in each end, and the tube may remain at rest a very long time without that oil distributing itself along the top of the tube. But with a little motion that oil will gradually work up to the upper side. So gravitation and capillarity alone are rather impotent unless they get this element of movement. It would not be necessary to have very extensive movement, but some degree of movement is essential. Now if natural gas, in addition to the method of origin by the action of bacteria on organic matter in mud, may also arise by pressure at great depth, as the overburden is added, a great deal of motion may result. I think more motion is produced in this way than by the descent of meteoric waters.

Jan 4, 1915

By Ralph Hayden

PAGE I. IntRoduction........239 II. Definition of Anaconda SLime....240 III. The Source of Slime......240 Remodeled Flow Sheet......240 Old Plow Sheet,.......242 IV. ConStitution of Slimes......243 Chemical........243 Physical.........243 V. The Slime Problem.......247 VI. THe Experimental Slime Plant....248 VII. Slime Thickeners. ETc .......249 Slime Ponds........249 Tanks.........249 Comparative Efficiency of Open and Baffle Tanks .260 Callow Tanks........252 Kuchs-Laist Centrifugal Separator....253 Garred Filter........256 Dorr Continuous Thickener.....256 VIII. Concentrators........257 Round Table........558 Peck Centrifugal Concentrator....259 Competitive Tests.......260 Twenty-Deck Round Table..... 260 Slime Feed Distributor......261 IX. ConcluSion.........262 I. Introduction. In the wet concentration of ores there is always a certain amount of very fine material with which to contend. and which invariably carries such quantities of value that the treatment of it is worth while. commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely. the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 1, 1914

By H. Scott

SINCE Böhler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar3_2_1 obtained by increasing the maximum temperature to which the material was heated, much has been published' connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The, significant facts established by recent investigators' are: that when the' transformation occurs at the higher temperature Ar', troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar' and Ar" adopted here is that of Portevin.3

Jan 2, 1919

By H. C. Boynton, Albert Sauveur

In the course of some experiments conducted in the Metallographical Laboratory of Harvard University, some interesting facts were brought to light which appear to be worth recording in advance of a more elaborate and exhaustive paper which the authors hope to present to the Institute in the near future. Fig. 1 shows, under a magnification of 100 diameters, the microstructure of the cross-section of a steel bar 1/2-inch square, containing 0.52 per cent. carbon, heated to 1100 degrees C. and cooled slowly with the furnace. Fig. 2 illustrates the structure of the same steel, heated to the same temperature but cooled more rapidly in the air. Both samples were cut from the same bar and heated side by side in the furnace. When a temperature of 1100 degrees C. had been reached, one sample was taken out of the furnace and allowed to cool in the air, while the other was cooled with the furnace. The only difference, therefore, in the treatment of both samples will be found in their respective rate of cooling. This variation in the rate of cooling resulted, as shown

Jan 1, 1904

By George S. Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro- posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By Alvinus Brown Wood

THE ancient copper-mines of Lake Superior, having been destroyed or covered by-modern mining-dumps, are not accessible to the present inhabitants of that region, and, since no more are likely to be found, some account of those already discovered, from one who has seen them, may be acceptable to the Institute. Early in May, 1855, 1 took a party of men to open an ancient pit on the Quincy mine-location. Mr. C. C. Douglas was the Agent.," as mine-managers were then called on Lake Superior. The Quincy Co. had previously done work on a fissure-vein, several hundred feet west of the Amygdaloid lode (afterwards called the Pewabic lode), on which was the ancient pit herein described. It was at this pit that the Quincy' main shaft was subsequently stink. The ancient pit showed an apparent depth of about 4 ft., but when cleaned out it was shown to be 14 ft. deep, having been filled up by the sliding-in of material composed largely of broken rock, taken out in sinking the ancient shaft, and left near its mouth. Midway of the shaft, and below water-level, was found a scaffolding, of white-birch poles,- which had been used as a landing, to assist in removing the excavated rock. The shaft was 7 ft. in diameter. The excavation had been done by first building fires in order to disintegrate the rock, as was proved by the abundance of charcoal found; then breaking the softened rock with hammers of diorite, such as is found in the greenstone range on Keweenaw point. These hammers had about. the size of large paving-stones. Only broken ones were found, the whole ones having been doubtless carried away for other work, such as could be traced on the lode for a hundred feet or more to the south. At the place where this shaft was stink, barrel-copper (i.e.,

Mar 1, 1906

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971

By R. A. Morse, W. W. Owens, D. R. Parrish, T. M. Geffen

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951