Search Documents

By J. O. Brittain, E. Lautenschlager

An investigation was conducted on fine grained airon wire to measure the influence of the temperature of deformation on strain aging near room temperature. Specimens were deformed various amounts at 77°, 195°, or 273°K and aged. The strain aging was followed by either internal friction or return of the yield-point measurements. The results show that strain aging occurs in three stages. During the first stage there is small, almost immediate return of the yield point. The solute carbon concentration, as mesured by internal friction, remains constant in stage I but is lower than the concentration in the unstrained condition. In the second stage, the solute concentration decreases while the magnitude of the yield point increases. In the third stage, the solute atoms continue to drain from the solution, the yield point approaches a maximum, and the strain-hardening coefficient and flow curve increase. The kinetics of the strain aging reaction are not the same for the two sets of measurements since the internal friction results lag behind the yield-point measurements. However, the strain-aging kinetics measured at 44° and 64°C showed no effect due to the difference in initial deformation temperature; nor were the strain aging kinetics influenced by low-temperature anneals at 77°, 195°, and 273°K. 1 HE object of this investigation was to measure the effect of initial deformation temperature on the strain aging of a-iron by tensile tests (i.e., return of the yield point) and internal friction methods, to correlate the results of the two measuring methods, and to measure the effect of low-temperature annealing (<273°K) after low-temperature deformation upon strain aging. The experiments were performed on fine-grained a-iron wire containing 0.02 wt pct c.l According to Thomas and Leak,&apos; return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solid solution, while the return of the yield point as a function of the aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,3 during aging the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point on subsequent testing. It has been shown that after low-temperature neutron bombardment, a-iron goes through a stage of recovery at low temperatures which can be attributed to the annealing of iron interstitials&apos; and/or vacancies.4 If, after low-temperature deformation, there is an interaction during a low-temperature anneal between mobile point defects and the solute atoms (i.e., carbon atom interaction with vacancy or iron interstitial), it is possible that some solute atoms will be found at defect sites other than dislocations. Such changes in the sinks for the carbon atoms might be expected to alter the strain-aging kinetics sufficiently to be detected by either inter-

Jan 1, 1962

By Casimir Constable

DURING the years 1875 to 1879 I had charge of the Rockwood furnaces and mines, situated forty miles from the nearest railway communication at that time, and one hundred miles north of Chap tanooga, Tenn., by the Tennessee River. The small furnace with old-fashioned stoves, then in blast, was built under great difficulties by General Wilder. The early conditions were somewhat as follows: The ore was fossil ore of the Clinton group ; very fine and generally wet, without other admixture. The coke had a large amount of ash, and the fur" nace appeared to be badly scaffolded at times. On many days only a few tons of iron could be obtained. The founder generally id creased the revolutions of the engine when signs of chilling appeared,. The cinder at such times was black, very scoriatious, often closely resembling mill cinder. When the pressure was increased (the joints being the old-fashioned rust joints), leaks in the blast-pipe occurred It was noted that when the blast was stopped, and the leak bolt imperfectly remedied, the furnace improved a little. This set me thinking on the right track; and I took the responsibility of be coming my own founder for a time. A scaffolded condition had existed, and the situation was a trying one. Strange to say the negroes proved excellent furnace-men. Conceiving the hearth of the furnace to be similar to the grate area of a steam-boiler, capable of disposing of but so much fuel per hour, and requiring only a corresponding amount of air, it follows that an excess of air will burn the fuel not yet arrived at the hearth!, and raise the melting-point far above the tuyeres. This might pro duce scaffolding or at any rate choke the boshes, and leave less fuel to be consumed in the hearth. Thus for the time being less ail;. would be needed, as the continued burning of fuel in and above the boshes, would only aggravate the trouble. This condition of affairs accounted for the black cinder; the heat above having melted ore not yet perfectly reduced. This view decided me to reduce the revolutions of the engine; thefurnace finally became gray, as might have been expected. Any attempt to increase the speed produced black cinder and hard iron ;

Jan 1, 1883

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia&apos;s energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia&apos;s energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By Edward V. D’Invilliers

In connection with some recent professional work in the coalfields of Western Pennsylvania, with special reference to results of coking operations, I was asked to compile a statement giving the estimated cost of mining coal and manufacturing coke at two hypothetical plants of 500 ovens each, giving the relative yield of coal in coke at each plant; and, upon the average number of working days in each of the past five years, from 1899 to 1903, together with average selling price of coke at the ovens, to prepare an estimate of the relative commercial returns in each district. What seemed at first sight to be a comparatively simple proposition, involving only the ordinary elements of mining and coking costs, became complicated by the lack of standard published records of mining costs and sales, which would be applicable to the subject at issue. Upon searching through the usual channels of Government publicatious and the files of our technical societies and mining periodicals, I was surprised to note the absence of fundamental factors that would approximately meet the case in point. The very elaborate and interesting statistics annually published by the National Government&apos; do not supply the required data for the following reasons:—1. Being reported by arbitrary districts, the average values are too general to be applied to special fields. 2. The value of coal charged to the ovens is apparently based upon the regional average value of the coal if sold in the market, and not upon the cost of production. 3. Some plants only use the slack (a by-

Jan 1, 1905

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By W. J. McKenna

THE International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov.&apos; 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. LABORATORY AND TEST MILL In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. PURCHASING OF ORE A new shipper usually sends to the plant a 25 to 50-lb. sample, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department&apos;s treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as concentrator feed. ORE TREATED The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages are received by rail and consist of crude ores and gravity mill products. Those from the Bingham district are received by rail and aerial tramway,

Jan 1, 1928

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By Edward H. Robie

THOUGH the final figures are not available as this is written, it seems certain that the Institute accounts will show $7000 to $8000 surplus for the year 1951. This is the first time this has happened since 1941. No money had to be taken from any of the Funds to bring about this happy condition. Furthermore, the amounts allowed for depreciation, bad debts, and inventory adjustment were more liberal than in the past. Income increased some $29,000 over 1950. Dues received from old members increased moderately, but dues from new members dropped off $2000 and from initiation fees quite severely-from $17,000 to $11,000. The number of new members did not come up to expectations and a change in procedure caused a delay in getting some of them on the rolls. A large number of the new members paid an installment of $5 on their initiation instead of the full $20. Junior Members, of course, pay no initiation fee. Brightest spot in the income picture was the increase in advertising income-from $103,000 in 1950 to $143,000 in 1951. All three of the journals shared in this, Mining being up $18,000; Metals, $9000; and Petroleum $13,000. Nonmember sales of the journals dropped off slightly, and sales of Transactions volumes more so from $35,000 in 1950 to $27,000 in 1951, with a further drop of $5000 accounted for by a change in accounting procedure. On the other hand, sales of other publications increased by $10,000.

Jan 1, 1952

By F. M. Stewart

A paper by Hurst and van Ever-dingen in 1949 led to the practical solution of many nonsteady-state flow problems.&apos; Subsequently, applications of this material have been discussed by several authors. The purpose of this note is to outline a simplified direct procedure for water-influx pressure predictions for pressures above the bubble point. The prcposed procedure is unique in that after the "time-conversion factor" and the "influx constant" are obtained, predictions are made without trial and error. The elimination of trial and error is made possible by expressing certain PVT characteristics as explicit functions of pressure. The procedure is applicable to fields producing at pressures above the bubble point and under radial water drive from an infinite aquifer. In the usual applications it is required to predict (1) withdrawals given future pressure history or (2) reservoir pressure, given future withdrawals or production. The theory, assumptions and conditions under which the nonsteady-state solutions hold are covered in the references and are not repeated. The simplified direct procedure outlined here has been developed from published solutions for the so-called "pressure case". A similar direct procedure for the same special conditions has been developed for the "rate case"; however, in this instance the procedure is lengthy and offers no advantage over the trial-and-error solution. Consequently, this paper covers only the procedure based on the pressure case. DISCUSSION Under the pressure case prediction of withdrawals from a water-drive field, given the future pressure history, involves the use of a nonsteady-state water-influx term together with the material balance equation. The solution of a particular problem requires the following steps: (1) division of past pressure and production data into equal time intervals; (2) computation of cumulative water influx vs pressure drop for each time interval of past history using the material balance equation; (3) determination of the best values for the "time-conversion factor" and the "influx constant" by equating the nonsteady-state influx term with the influx computed in Step 2 (this requires a trial-and-error procedure); (4) prediction of influx for a given pressure drop using the influx term and the computed factors from Step 3; and (5) calculation of fluids produced using the predicted influx in the material balance equation. A forecast of the water-oil ratio or water production rate is required to complete the calculation. It is assumed that a reliable estimate of original oil in place is available, as well as the production and pressure history, and data on reservoir fluid characteristics. If the original oil in place is unknown, it may be computed simultaneously with the tinie-conversion influx factors2,3. However, the oil in place so computed may be considerably in error3; consequently, it is usually preferable to use oil in place estimated from pore-volume data unless there is considerable doubt as to its accuracy. The Material Balance Equation Above the Bubble Point Above the bubble point the simpli-

By F. G. Miller, R. C. McFarlane, T. D. Mueller

During the process of gas storage in pressure-depleted oil reservoirs, it has been observed that in some instances additional liquid oil is recovered and that the composition of the storage gas is materially altered. A mathematical study was made of the dynamic behavior of such a depleted oil reservoir undergoing gas injection. The important variable considered in this study, not included in previously published work, was that of compositional effects on the phase behavior of two-phase flow. Pressure, saturation and component composition profiles were developed for a linear, horizontal and homogeneous porous medium containing oil and gas but undergoing dry gas injection. Special new techniques were developed to overcome the problems of numerical smoothing which arise in the solution of the equations representing such systems. The method of solution includes the development of partial differential equations describing the behavior of the system, representing these equations by finite difference approximations, making certain simplifying assumptions and, finally, applying methods of numerical analysis with the aid of a high-speed digital computer. In an example calculation, results using the mathematical model are compared with field observations made on a gas storage project in Clay County, Tex. This field project involved a depleted oil reservoir used &apos;for gas storage and gas cycling purposes. As a result of these processes, the reservoir yielded substantial amounts of secondary oil, both in the form of stock tank oil and as vaporized products in the produced gas. The methods derived in this study may be applied to a variety of oil reservoir problems which are dependent on compositional effects. In recent years the number of oil reservoirs being used for gas storage purposes has increased greatly, and there has been at least one published account of additional oil recovery resulting from gas cycling a depleted oil reservoir after repressur-ing with dry gas for storage purposes. Additional oil recovery from oil reservoirs resulting from gas storage operations could become an important secondary recovery process. This is especially true since the use of natural gas in large metropolitan areas continues to increase and more gas storage volume near these areas is needed. These facts provided the motivation for the work reported here. This paper reports on a study of the inter-relations of composition, saturation and pressure changes which occur when hydrocarbon gas is injected into an oil reservoir system. From an understanding of the process, prediction methods may be developed for use in forecasting the secondary recovery products from gas storage operations in oil reservoirs and, consequently, .the economics of such projects can be developed. The process of storing hydrocarbon gas in an oil reservoir and the cycling process both involve the transient multi-phase flow of oil reservoir fluids with changing fluid compositions. There is a scarcity of work published on the subject. One of the first laboratory models developed to study a problem similar to the one posed here was published in 1948 by Standing, Lindblad and Parsons. l They developed a model to study gas condensate recovery by gas cycling, including the effect of heterogeneous reservoir permeability. Their results showed the compositional effects of injecting a gas of known composition into a two-phase condensate reservoir of known composition. A major finding of their study indicated that maximum oil recoveries from gas cycling projects result when low cycling pressures are used. Previous to their work it was generally considered

By D. J. Carney, J. Chipman, N. J. Grant

SINCE the beginning of this century it has been known that hydrogen contributes to the porosity of steel and that it is harmful to its mechanical properties. The evidence for this has been largely qualitative. Steel to which hydrogen was purposely added. in sufficient .amounts was shown to be either porous or brittle or both, whereas similar steel of low hydrogen content was shown to be free of porosity and to possess normal physical properties. There have been a considerable number of qualitative experiments of this type. Also, early in this century, a few attempts were made to measure the amount of hydrogen normally dissolved in commercial steels. This was usually done by placing the sample under an inverted liquid column such as mercury and collecting the evolved gas. These attempts, while not successful in measuring actual amounts of dissolved hydrogen gas, were able to prove that this gas will diffuse out of steel at room temperature, and that the amount of hydrogen dissolved is normally very small. On the basis of such qualitative evidence, hydrogen has been and still is blamed for a great number of the troubles encountered in the steel industry. In recent years, partial solutions for many steel-working problems have been obtained. These have led to increased interest in accurate quantitative work on hydrogen in steel, with the expectation that the results might possibly answer a few of the remaining unsolved problems. Commercially, two of the obvious questions which are in need of an answer are: (1) what are the most important sources of hydrogen, and (2) what quantity of hydrogen can be tolerated in various steels? There are many other unanswered questions. To begin to find the answers it seemed logical to start at the beginning of steel production with the liquid metal. Further, it seemed almost imperative to solve first the problems of analysis and sampling of the metal for hydrogen. Once these problems have been solved, it would be possible to answer more of the important commercial problems mentioned above. As a consequence, it was decided to design an analytical apparatus and, upon satisfactory completion of this, to develop an accurate method of sampling liquid metal for hydrogen.

Jan 1, 1951

By G. W. Thomas

A simplified mathematical model of underground conduction heating in a system of limited permeability is presented. The model applies to underground retorting of oil shale, or to reservoirs containing extremely heavy oils. We assume that heat is introduced at a constant rate into a horizontal fracture which communicates between wells. The radial temperature distribution along the fractured surface is approximated by a step-function. Heat transfer away from the fracture is assumed to be by vertical conduction, and all convection effects are neglected. The model also takes into account the possible temperature dependence of thermal conductivity. A general expression for calculating the growth of the step-function temperature distribution with time is derived. The use of this expression and solutions to the one-dimensional heat equation make it possible to construct isotherms. Expressions for calculating .oil recovery, well spacing and heat efficiency are also given. An example calculation is presented for the conduction heating process in oil shale. Finally, the effect of the heat transfer coefficient between the gas and the fracture boundaries is investigated. INTRODUCTION Thermal recovery processes of oil recovery fall into the four general areas of hot fluid injection, forward combustion, reverse combustion and conduction heating. The first three of* these processes have been rather extensively studied in the past decade from both the experimental and theoretical points of view. As a result, it is possible to make reasonable engineering predictions and analyses of these processes. Little attention has been devoted, however, to the conduction heating process other than to note its possible utility.I To a certain extent, conduction heating cannot be divorced from the other regimes cited above, insofar as these provide the source of heat energy. In the conduction heating process, heat is introduced (either by combustion in the forward or reverse mode or by hot fluid injection) into a small fraction of the total reservoir thickness. This fraction may be either a streak of high permeability or an interwell fracture. Heat penetrates by conduction into the adjacent, less permeable regions of the oil-bearing rock, where the direction of conduction is essentially perpendicular to the streak or fracture. The heated product then drains by gravity or is gas driven to production wells. Conduction heating is probably most applicable to systems containing immobile bitumens such as tar sands and oil shale deposits and perhaps to low-permeability reservoirs containing highly viscous crudes. The mechanism also acts in combination with other thermal processes where fingering or overriding of a bed occurs. It seems probable that in at least one field test, conduction heating of this type was very influential.2 In this presentation we give a first approximation to some of the quantitative aspects of conduction heating. Marx and Langenheim3 treated a similar problem where they focused attention upon the injection interval, which spanned the total reservoir thickness. In their model, conduction heat losses to the bounding media imposed a practical limit on the calculated heated area. In the present study, however, we shall confine the injection interval to a small fraction of the reservoir thickness and assume it has no heat capacity. We therefore direct our attention to regions outside the injection interval into which the conduction of heat is beneficial. In particular, we will endeavor to locate specific isotherms in the media bounding the injection interval. Furthermore, we will construct our model to allow the thermal conductivity to vary arbitrarily with temperature. Thus the model will be applicable to underground retorting of shale where variations in thermal conductivity may be important. THEORY We consider the rock matrix to have no or, at best, a very limited permeability; consequently a

Jan 1, 1965

By W. A. Tiller

The unidirectional freezing of a semiinfinite liquid from one end has been treated by calculating the solute and temperature distributions in the liquid and solid phases with time, when the solid-liquid interface advances at a rate proportional to (time)lt2. The nucleation probability for new grain formation is calculated as a function of the constitutional and thermal properties of the alloy, the pouring conditions and the catalytic efficiency of the nucleating agents. The transition from columnar crystal formation to equiaxed crystal formation is assumed to occur at a critical nucleation frequency for a particular alloy and the quantitative dependence of the ratio (columnar zone length/equiaxed zone length) upon the freezing conditions has been predicted. The effects of (i) fluid flow in the liquid, (ii) heat transfer through a mold wall, and (iii) a finite ingot length, have been explicitly tveated as departures from ideality. These departures from ideality are found to have very important consequences on the ingot stmcture. In Part I&apos; of this series, a qualitative description of the general ingot structure was developed. The factors that determine i) the ratio of the equiaxed zone length to columnar zone length and ii) the grain sizes in these zones, were discussed. In the present paper, topic (i) will be treated quantitatively, and it is intended that topic (ii) will be treated quantitatively in Part 111. The complete treatment has been split in this manner for ease of development and coherency of presentation. The treatments are quite mathematical in nature and, although some of the conclusions to Part 11 depend upon the treatment presented in Part 111, it was felt that the intended audience would find the material more readable and more useful in its present form. To this same end, it seems worthwhile to reiterate some of the qualitative aspects of grain nucleation during ingot solidification before embarking on the mathematical description. QUALITATIVE ANALYSIS In the conventional method of casting, a liquid alloy with a certain degree of superheat is poured into a mold. The outer rim of liquid metal cools rapidly to the liquidus temperature of the alloy and begins to undercool. As the degree of undercooling increases, nuclei of solid begin to form in this chill layer, this nucleation being catalyzed by certain heterogeneous particles in the liquid. The grains in the chill layer which are generally of random orientation, begin to grow inwards because of heat conduction through the mold. The grains usually develop a columnar shape since the frequency of nucleation of new grains in the liquid ahead of the advancing interface is generally insufficient to seriously impede the growth of the original grains. Due to the slow diffusion rate of solute in the liquid, a solute distribution is formed in the liquid adjacent to the interface which is either an excess or a depletion if the partition coefficient, ko, of the solute is < 1 or > 1, respectively. Thus, the liquidus temperature of the liquid adjacent to the interface is a function of position. The actual temperature in the liquid is also a function of position and the temperature gradient at the interface decreases as the interface moves away from the mold wall. Since the rate of advance of the interface decreases with time, the equilibrium temperature distributions and the actual temperature distributions as a function of interface position, X, can be illustrated as in Fig. 1. Thus, a region of liquid may exist in which the actual temperature is below the liquidus temperature. This liquid is contitutionally supercooled and therefore unstable with respect to the nucleation of new grains. Now, since the supercooling in Fig. 1 increases as the interface moves further away from the mold wall, the nucleation rate of new grains will increase. When the nuclea-

Jan 1, 1962

By D. Jeulin

For iron ore sinters to be good blast furnace burden, they need to possess certain basic properties such as cold mechanical strength, reducibility, etc. Relations between such basic parameters and sintering parameters (composition of the mix, fuel consumption, operating conditions of the sintering plant, etc.) are not always well understood. For example, one cannot explain the differences in quality noticed for sinters having the same chemical composition. In this paper a new approach is proposed for the characterization of iron ore sinters by a quantitative description of their morphology. The Texture Analyzer LEITZ T.A.S. is used for this purpose and such morphological parameters as sizes of microstructures and the size distribution of phases are measured on samples of sinters. The results indicate that these measurements can be correlated with the sinter quality.

Jan 1, 1977

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley&apos;s second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

By Elmer W. Pehrson

THE founding of the American Institute of Mining Engineers in 1871 came at an unusually significant moment in the life of our country. The industrial revolution, in which mineral production played a major role, was just getting underway. The iron industry, established several decades earlier, was reaching sizable proportions. In 1871 pig-iron production was approaching 2 million tons, and the industry had spread as far west as Missouri and Wisconsin. The chief sources of iron ore were Pennsylvania, New Jersey, New York, and Michigan. The age of steel was in its infancy; production had not yet reached 100,000 tons per annum. The gold rush to California two decades earlier and the discovery of other gold and silver bonanzas in the West paved the way for the transcontinental railways, which were then being built and which contributed much to the subsequent development of the great copper, lead, and zinc districts of the Rocky Mountain area. Regular production of copper in the Michigan peninsula and of lead in Missouri and the upper Mississippi region had been established for many years but on a scale dwarfed by the quantities later required as technical progress, invention and enterprise made possible the rapid expansion of industry. Discovery of oil in Pennsylvania in 1859, the growing recognition of the

Jan 1, 1947

By C. K. Leith

AT the outset I would like to make it clear that I do not enter this discussion in a controversial spirit, but in an attempt to contribute something helpful to an understanding of a difficult problem. I have too high regard for the sterling quality of the work of the men who have studied this subject in detail to offer anything in the way of essential contradiction to their statements of fact. Difference of opinion arises from differing valuation of the possible alternative hypothesis which these facts suggest. Some degree of recrystallization in limestone contact zones has been recognized by many investigators. Earlier investigators, for the most part, assigned an important, if not the most important, role to recrystallization in development of these zones. With the growing recognition, of introduction of ores and gangue materials into the contact zone from igneous rocks through the medium of primary magmatic solutions, there has been a tendency to ascribe to this process most, if not all, of the chemical and mineralogical characteristics of the contact zone. This has involved a correspondingly diminished emphasis on recrystallization of substances already there as a factor in the process, and in some cases even the complete elimination of this hypothesis. From detailed study of a few contacts, casual observation of others, and a general familiarity with the literature, some of us have been led in recent years to raise the question whether the pendulum has not swung too far away from recrystallization toward direct introduction from igneous sources, and to argue for more recognition of the part played by recrystallization.1 The inevitable sequence has been that those of us who have taken this view have been charged, at least by inference, with emphasizing recrys-tallization to, the total exclusion of the alternative process. Scientists, like other men, like to classify and pigeon-hole views under simple and definite designations, leaving out qualifications which would tend to make the classification more difficult to state. This has made the problem seem more definite and simple, but has tended to obscure the fact that the disagreement is primarily not one relating to essential facts, but one of

Jan 6, 1914

By Irving Lipkowitz

While the light metals are recognized generally as a distinct group in technical literature, economic classifications and data usually still treat them as part of the nonferrous group of metals. However, the economic characteristics of the light metals also differ markedly from those of other nonferrous metals. The distinctiveness of the light metals, as, a group and individually, becomes evident when their growth, since World War II is compared with that of other metals, as in Table 14.3.1. The growth of light-metals production has been much sharper than that of other metals. A weighted average for the light metals shows an increase of 112% during the 1958 to 1968 period. This compares with a 62% increase in the "All Primary Metals" component of the Federal Reserve Board Index of Industrial Production. The contrast was even sharper during the next six years (1968-1974), with light metals production up another 50% as against a 21 % increase in the FRB Primary Metals production index. The most important reason, however, for considering light metals separately is the trend and pace of technological change and not their distinctive statistics. Technology both creates and demands increasingly sophisticated materials. As technology advances and as all the world makes more extensive use of advanced technology, the importance of the light metals is likely to accelerate rapidly. There may be a profound clue to the future in the fact that light metals were predominant among the materials used in the construction of the Apollo 11 spacecraft. In determining what materials to use for the spacecraft and its equipment, the National Aeronautics and Space Administration (NASA) has explained that it did not look to "some of the more exotic metals" and relied instead on "generally proven materials." Accordingly, it apparently used a wide variety of metals, including precious metals, rare earths, special steels, copper, and light metals. What seems particularly significant is that, in seeking performance, NASA relied as heavily as it did on the light metals. Materials breakdown estimates show that aluminum accounted for over 75% of the materials used, titanium for another 5%, and magnesium was also used. Thus, light metals accounted for over 80%&apos; of the materials used for the Apollo 11 spacecraft. The light metals are also unique in their availability. They rank high in abundance among the elements in the earth&apos;s crust. Aluminum is the third most abundant element, after oxygen and silicon, with magnesium ranking eighth, and titanium ninth. Among the structural metals, aluminum is the most abundant in the earth&apos;s crust, iron is second, magnesium third, and titanium fourth. This potential availability of light metals provides strong incentives for continuing improvements in process technology, because of two major national problems: (1) there is

Jan 1, 1976

By J. W. Spretnak, G. W. King

THE crystallography and morphology of 0-Al,Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 p. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack&apos; found that ?-A13Fe (more correctly All13Fe4) belongs to the monoclinic system. Using Black&apos;s structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (00l)? || (110)Al [100]? || [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964