Search Documents

By Paul J. Sirkegian

A detail of the guide rollers is shown on Fig. I; and Fig. 2 shows a photograph of a guide roller that has been in service for several months on the haul-back cable. The former practice of supporting and guiding the haul-back cable on slusher hoists at Kimberly was accomplished by using the conventional type of snatch-block pulley, but it was found that an excessive amount of cable whipping and unreasonable wear on both rope and pulley resulted from this type of cable support. The guide, which is wholly made in the Corporation's shops, consists of two vertical and one horizontal roll assembled in a frame that is lagged to the cap timber in a slusher drift. In some slusher drifts more than one guide-roller assembly is used, depending upon the length of the drift. The installations usually are placed at 30-ft. intervals. We have found by actual experience that these rollers have increased the life of the haul-back cable approximately 200 per cent, as compared with the usage of the conventional sheave-block pulley. Cable Care The underground rigging crew and the slusher operators are trained in rope splicing. No cable clamps or knots are permitted on slusher cables and all cable "eyes" are spliced. The standard practice has been to use preformed cables of ?-in. diameter for haulage and ½-in. diameter for the haul back. The preformed cables have proved to be important factors for safety in use and speed in making splices. No external lubrication is used on the cables. It has been found that dry ropes have about 400 per cent longer life than those that were lubricated under these operating conditions. An accurate record is kept of all cable life and the tonnage moved by the slushers in each working place, and if the rope wear is excessive in any particular working place, an investigation is made to determine the reason. Wire-rope Sling for Snatch-block Anchor The rope sling is shown by Figs. 3 and 4. These slings support the snatch-block pulley for the haul-back rope. The standard practice at Kimberly is to use a roller-bearing snatch-block pulley 10 in. in diameter. The snatch-block housings are equipped with a clevis attachment in preference to swivel hooks, as it has been found that the more rigid clevis keeps the cable in better alignment. The snatch blocks are hung from the cable sling, which is wrapped around the posts of the drift sets as shown on Fig. 3. This method of anchoring the pulley provides better anchorage and flexibility than those of the rigid or spring-mounted types. When the slusher-drift headings are being advanced, the snatch blocks are hung from a "gin" pole ahead of the last set of timbers' An employee is assigned on each production shift to take care of the lubrication of all slusher hoists that are being used and he is provided with tools for minor repairs.

Jan 1, 1946

By S. Floreen, R. M. Pilliar, H. W. Hayden

The fracture behavior of a 50 pct Cu-50 pct Fe mi-croduplex alloy, laminated composites of copper and iron and an extruded 50-50 Cu-Fe elemental powder composite was studied. Very low ductile-brittle transition temperatures were achieved in all cases, but for different reasons. In the microduplex alloy both the initiation and also the propagation of cleavage fractures appeared retarded by the very small in-terphase distances. In the composites, crack propagation through the sumples was prevented in most cases by delamination fractures perpendicular to the advancing cracks. These delaminations occurred at different regions and by different mechanisms in the various composites. In the extruded powder composite, de-lamination appeared to take place along preexisting flaws. In the crack arrest geometry of the laminated plates, delamination took place by localized shear fractures within the copper near the Fe-Cu interfaces. In this case delamination was enhanced by thicker laminate layers, and by having the resistance to shear failure of the copper sufficiently low compared to the toughness of the iron. BRITTLE fracture in engineering materials has long been a problem, and many different ways of preventing it have been considered. One method that has been of growing interest lately is to prevent crack propagation by the introduction of mechanical discontinuities into the structure. These discontinuities may act in several ways. They may simply act as crack stoppers. They may introduce secondary fractures such as de-laminations that deflect the initial crack into new, less damaging directions. Alternatively, they may subdivide a fairly large bulk sample that would have been loaded in plane strain, for example, into a number of subunits that are individually loaded in plane stress and thus are more resistant to fracture. Other mechanisms, or combinations of mechanisms, are also feasible. A number of methods exist for introducing mechanical discontinuities into a structure. Composites by their nature have discontinuities in structure, and numerous studies have shown that fracture propagation in materials of this type can be radically changed by suitable control of the composite parameters. Of particular significance to the present work are recent investigations of layered composites made by joining high strength steel sheets by various means.'-4 These studies have shown that through proper control of the mechanical properties of the bonds joining the sheets it was possible to introduce delamination fractures that markedly improved the overall toughness of the composites and in some cases completely prevented through-the-thickness fractures. Another technique for introducing structural discontinuities is simply to use a two-phase alloy. It has been recognized for many years that a small amount of a second phase may improve toughness either by homogenizing plastic flow and thus preventing localized stress concentrations that nucleate fracture, or by interacting with an advancing crack. In most of these studies of two-phase materials, the decreases in ductile-brittle transition temperatures produced by the second phase were relatively small. More recently, work on two-phase stainless steels having a very fine grain microduplex structure has shown that the presence of on the order of 40 to 50 pct of a tougher second phase may lower the ductile-brittle transition temperature of the brittle phase by approximately 300°F. 5-7 In these alloys delaminations were seldom observed. The tougher second phase appeared to minimize the ease of both the initiation and the propagation of cleavage fractures. These results show that both the composite approach and the microduplex alloy approach are effective methods of preventing brittle fracture. Therefore, it was of interest to compare the fracture behavior of a microduplex alloy with composites made from the two-phases that were present in the alloy. To simplify this comparison the 50 pct Cu-50 pct Fe system was selected for study. At low temperatures the equilibrium tie line phases in this system are essentially pure ferrite and pure copper. A 50-50 alloy was cast and hot worked to produce a microduplex structure. Two types of composites were studied; laminated structures prepared by roll bonding iron and copper sheets of the tie line compositions, and an extruded powder composite made from high purity elemental powders. The fracture behavior of these materials was then compared. EXPERIMENTAL PROCEDURE Alloy Preparation. The 50-50 Fe-Cu alloy and the components for the roll bonded composites were prepared by vacuum induction melting 30-lb heats using electrolytic grades of iron and copper as charge materials. A carbon boil was used to deoxidize the melts. Small additions of copper and iron were made to the iron and copper heats, respectively, to approximate

Jan 1, 1970

By Burdett Loomis

The advantages of gaseous fuel have been too fully set forth during the past few years to need recapitulation. Papers, arguments, and editorials have been issued, in a more or less general way, that would make volumes. Systems have found zealous advocates, and many promises of results that have sounded strangely in the ears of old-fashioned gas-makers, have been born of theory, and have died in the earliest throes of trial; while in some few instances success has demonstrated the value of practical effort. With few exceptions, however, everything attempted or accomplished has tended towards the one end-—the realization of more perfect results than we can

Jan 1, 1891

By R. H. Schnitzel

Internal-friction peaks have been observed in tungsten single crystals at about 300° and 400°C. The characteristics of these peaks are similar to interstitial peaks observed in other bee metals; therefore, the origin of these peaks appears to he the Snoek mechanism. The interstitial responsible for the peak at about 300°C has not been identified. Carburizing increases the magnitude of the peak at about 400°C; consequently, it appears reasonable to suppose that the specific interstitial associated with this peak is carbon. The activation energies associated with the 300° and 400°Cpeaks are about 35,000 and 45,000 cal per mole, respectively. INTERNAL - friction peaks resulting from the stress-induced diffusion of interstitials (Snoek relaxation peaks) have been frequently observed in bee metals.1-5 Attempts to detect Snoek relaxation peaks in tungsten have, however, not been fruitful.' Failure to find Snoek peaks in sintered tungsten can perhaps be attributed to one or more of the following difficulties: a) the relatively low purity of the sintered tungsten; b) the lack of extensive metallurgical knowledge about tungsten-interstitial alloys, such as suitable interstitial dosing and quenching procedures; and c) the inconsistency of some of the interstitial analyses of tungsten, which reflects itself in one's inability to be sure of the nature of the specimens. This present investigation did not overcome all of these difficulties for successful tungsten internal-friction measurements. Some of these difficulties still persist and new difficulties were encountered during the course of this investigation. Nevertheless, the use of electron-beam tungsten single crystals having somewhat greater purity levels than sintered tungsten combined with appropriate carburizing and quenching procedures permitted a reasonable attempt to be made. As a consequence, internal-friction peaks were observed in these tungsten single crystals at about 300° and 400°C. These peaks were found to be unstable, since they annealed rapidly away during a sequence of internal-friction measurements. Hence, it was necessary to construct an apparatus having a faster heating rate to study some of the details of these peaks. From the behavior of these peaks as well as our knowledge of similar peaks in other bee metals, one can reasonably conclude that these peaks are caused by residual interstitial impurities within these crystals. Further investigation of these peaks after the application of various metallurgical treatments lent credence to this supposition. EXPERIMENTAL TECHNIQUE The internal friction of tungsten single crystals was measured using two different pieces of apparatus both of which are of essentially the same conventional design, namely the KE type of torsion pendulum. The important difference between these two types of apparatus was in the attainable heating rate and method of protection of the specimen from atmospheric contamination. The apparatus designated "number 1" was enclosed in a vacuum chamber which was heated by an externally mounted furnace. It had a slow rate of heating which was estimated to be about 4°C per min from room temperature to about 350°C and then about 1°C per min to 600°C. The internal friction of tantalum was measured with this apparatus and the established Snoek peaks were found.' These tantalum peaks in the temperature range from room temperature to 400° C served as a check for the apparatus. The apparatus designated "number 2" having a faster heating rate than number 1 was not elaborate. It consisted of a mounted nickel tube to which split heating elements were attached. Argon was used as the protective atmosphere. The measured heating rate was about 12° to 15°C per min whereas the cooling rate was somewhat slower at about 10° C per min because of the increased difficulty encountered in stabilizing the temperature. No surface oxidation of the specimen was noted after any test. This apparatus was also checked with the known peaks of tantalum.1 The preparation of the single-crystal specimens for internal-friction measurements consisted of centerless grinding the crystals from an approximate 0.200 in. diameter to 0.030 to 0.040 in. in diameter, and then electropolishing them to about 0.020 in. in diameter. Single crystals processed in this manner are designated as being in the virgin condition. Since the length of crystal varied from 3 to 9 in., the test frequency varied from about 1 to 2 cps. The frequencies of measurement, axial orientations, and chemical analyses for the various crystals are listed in Table I. The controlled addition of carbon into tungsten is a difficult problem. Attempts to find the critical conditions necessary for an equilibrium treatment were not fruitful. Therefore, a simple nonequi-librium method was used. The addition of carbon to these crystals consisted of appropriately combining three treatments—carburizing to achieve a case, annealing to partially dissolve the carbon into the

Jan 1, 1965

By Leland L. Mink, Roy E. Williams, Lewis M. McNay, Alfred T. Wallace

In 1968 the metal-mining industry of northern Idaho installed tailings ponds as a means of handling and treating mine wastes, metallurgical process wastes and domestic wastes. The installation of the ponds constituted a crash program to minimize pollution of the Coeur d'Alene River. The ponds provided an opportunity to investigate which combinations of wastes tailings ponds can be treated. The research data pertaining to tailings pond discharge lends insight into compliance with the recent EPA guideline for effluent quality.

Jan 7, 1973

By S. S. Rumsey

Introduction IN order to realize the economies which would result in operating the mine pumps at the Chapin mine with electricity. generated by water power, the Oliver Iron Mining Co. recently installed a hydro-electric plant at the upper Quinnesee, falls on the Menominee river, and constructed a transmission line to the mine. On account of the large flow of water in the Chapin mine, and the great depth from which it has to be handled, it was necessary to make a thorough investigation of the merits of both the motor-driven centrifugal and motor-driven plunger pumps, in order that the most economical results as regards power, cost of installation, maintenance, and operation, be obtained. This investigation resulted in the selection of motor-driven centrifugal pumps, as the cost of the pumps and motors, installation, and maintenance was considerably lower, and the space required in the underground workings very much smaller, than for the plunger pumps. The overall efficiencies guaranteed by several of the centrifugal-pump manufacturers were so nearly those guaranteed by plunger-pump manufacturers that the saving in power which would result from the installation of plunger pumps did not justify their increased first cost and the increased cost of installation under the conditions prevailing at the Chapin nine. In order to substantiate the representations of the centrifugal-pump builders it was deemed necessary to insist upon a factory test of the completed units before shipment, the test to be conducted under conditions of head and capacity approximating as nearly as possible those under which the pumps would operate in service. Furthermore, it was considered necessary to demonstrate, by test, that there were no deficiencies in design or capacity of the pumps or motors before their final installation in the mine, as it would be extremely difficult to make alterations in the pumps or motors after they were installed.

Jan 10, 1914

By E. E. Bauer

Technical data describing the critical points for selection of the proper hammer and of the boom and power pack for mounting on mobile gyratory crusher installations are presented. Charts describing typical rocks with breakability indexes for hammer selection are included. Comparative data of representative available hammers along with criteria for evaluating hammer selection are also presented. Factors affecting the selection of the boom and the power pack, as well as optional features for ease of operation and improved safety are described.

Jan 1, 1986

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite," and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe,O,) and maghemite (gamma-Fe,O,) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, how- ever, occurs largely as goethite (Fe,Os.H,O) and hematite (Fe90,) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated.

Jan 11, 1960

By E. Beril

This may be a most unnecessary paper—from what does crude oil come and how was it formed. Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important industrial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion. Older Theories There is no doubt that plants were the parent material of coals, but opinion is divided as to the parent material of crude oil and asphalts. One group of specialists believed that they were formed from dead fish. The hydrocarbons of crude oil were formed by the splitting off of CO² from fatty acids formed by the saponification of the fat (glycerides) of fish. Enormous quantities of crude oil are present in many places on the earth, very often in several nonconnected horizons at the same location. This could hardly be explained by the so-called "catastrophe theory," which states that fish died through the entrance of salt water into fresh water, and vice versa. Furthermore, this theory cannot explain the presence of aromatic hydrocarbons, which can be found in nearly all oils, especially in the oil of the Netherlands Indies, which has more than 50 per cent of aromatics. Geological and chemical observations both lead to the belief that the temperature of formation of asphalt, crude oils and coals, perhaps with a few exceptions, did not exceed 200° C. Chlorophyll and haemin derivatives, which decompose above 200° C., have been found in all these materials by Treibs and others. Thermodynamic considerations show that the temperature necessary for the conversion

Jan 1, 1938

By J. I. Budnick, W. B. Ittner III, D. P. Seraphim

A reliable technique has been developed for producing single crystals of tantalum in the form of small diameter wires. By suitably heat treating these and polycrystal samples, first in an oxygen atmosphere and finally in vacuum, it has been found possible to reduce residual resistivities to 10-3 microhm-cm. The purity of these samples is thus comparable to the purities obtained in zone-refined silver, copper, and aluminum. THE growth and purification of pure single crystals of the transition metals is, in general, difficult. The high melting and annealing temperatures of these metals make it necessary to employ rather special techniques in any crystallization process. In addition, the transition metals show a great affinity for and are easily contaminated by nitrogen, oxygen, and carbon. Recently, however. a number of investigators have been successful in growing,

Jan 1, 1961

By W. B. Vietz, C. W. Hill, T. P. Thomas

FLUXES, in general, may be classified according to their use as soldering, foundry or casting, and metallurgical and the chemistry of their action follows quite closely this division. The term foundry or casting fluxes, as used here, refers to the substances added to molten metals, preparatory to casting into molds or ingots, with the object of removing small amounts of impurities that have been introduced in handling or melting the metal, which was placed in a fair state of purity by the previous refining or metallurgical processes. The sources of these impurities are the oxide coating on the surface of the ingots, material extracted or mechanically removed from the crucible or furnace wall, and those formed by the reaction of the molten metal with the heating gases or furnace atmosphere. As commonly used, the term fluxes is applied to such materials as ammonium chloride, zinc chloride, salt, borax, and boric oxide. A second class of materials, usually called deoxidizers, includes substances such as metallic phosphides, sub-oxides, carbides, and bo-rides, that reduce the metallic oxides present in the metal. A third class includes various compounds that arc molten and non-volatile at the temperature of the molten metal and are used primarily to protect the surface of the metal from the action of the furnace or exterior atmosphere; to this class belong such mixtures as lime and fluorspar, lime and soda ash, various minerals, etc. In some cases these protective layers may act in a manner similar to the metallurgical fluxes and dissolve or unite with the oxide impurities of the metal, but as generally employed this latter action is negligible since there is little opportunity for the coverings to come into contact with more than the surface of the metal, and hence they arc without action on the body of the molten mass. The use of fluxes is the result of factory experience and tradition, but an extensive study has not been made of the chemical and physical actions that occur or the effects of these actions on the properties of the metal. It would seem necessary in any successful study of metal fluxes to determine not only what impurities are present in metals melted under

Jan 1, 1921

By George J. Bancroft

It is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Dansactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,' showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny? distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many. of Prof. Kemp's ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.V his theory, dealing with the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1908

By M. C. Leverett

KNOWLEDGE of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum pro-duction, but is as yet incompletely devel-oped. The object of this paper is to show the application of well established thermody-namic and physical principles to these prob-lems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: I. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion of mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. CAPILLARY EQUILIBRIUM IN SANDS Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treat-ment of problems of mixture flow, the con-cepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis-turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predict-able from the theory of capillary equi-librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, of course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is as-sumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reser-voir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems in-volving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately in-vestigated experimentally. Experimental evaluation of the pertinent properties of natural reservoir rocks will permit the ex-tension of the numerical treatment to prob-lems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids; that is, the manner in which the reservoir fluids are distributed vertically when the forces due to capillarity are just balanced by those due to gravitation.

Jan 1, 1940

By Paul Gordon

It is shown that equations for grain-boundary migrntion given by Gordon and Vandermeer, based on a theory first advanced quantitatively by Lucke and Detert, satisfactorily explain recent data on both GRAIN boundary migration in recrystallization and in postrecrystallization grain growth has been the subject of extensive studies for many years. Only solute-independent and solute-dependent boundary migration during recrystallization in zone-refined, poly crystalline aluminum, and during grain growth in zone-refined tin. with the advent of zone-refining, however, has it been possible to carry out such studies on high-purity metals, and thus to delineate quantitatively the major effect On the migration rates of very small percentages of dissolved imPurities. Earlier exPerimental work almost invariably gave migration rate parameters which disagreed with theoretical predictions

Jan 1, 1963

PAUL D. MERICA,* Washington, D. C. (written discussion t).-This paper is a discussion of some of the results of a recent investigation1 of Prof. Zay Jeffries, and of his interpretation and generalizations from these results. This work I have followed with great interest and with appreciation of its value in clarifying our views on the nature of deformation in metals and its relation to structure. It is only by such close study of the relation of structure to mechanical properties that we shall ever be able to describe the latter in terms of their ultimate elements, and thus explain what are still mysteries in the mechanical behavior of metals; experiment and thought along these lines are in my opinion of the utmost value. If I, therefore, here record some of the difficulties I have experienced in understanding some of the generalizations of Prof. Jeffries, it is only in order that perhaps from the discussion may emerge a clearer and more consistent statement of hypothesis or theory in explanation of the facts discovered by him.

Jan 11, 1918

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper' presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions', and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

By H. N. Lawrie

This study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility—two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten and Levo1,² using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleability-tests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi,O,, on the copper protoxide, CuO. Hampe's conclusioris of the influences of these two latter compounds of bismuth on copper are as follows : "If the protoxide of bismnth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Jan 1, 1910

By Albert Sauveur

Some writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transitionV stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By G. D. Van Arsdale

THE paper of Mr. Posnjak presents a laboratory confirmation of the well known facts that air ox-idation of pure solutions of ferrous sulfate is slow and difficult and that, like many other similar reactions, the speed, may be greatly accelerated by the presence of other substances, often in very small amounts, the effect of the presence of copper being determined ex-perimentally in this case. However, it should not be. overlooked that copper is always present in heap leach-ing solutions in amounts equal to or greater than those in the experiments described; therefore the paper may be considered as an explanation of present results rather than a possible improve-ment to be added to present practice. It is not practicable and it does not pay to precipitate copper by ce-mentation below a point about 5 lb. per 1000 gal., equivalent to about 0.0005 mol. Cu. per liter, compar-ing with the approxi-mately 0.0009 mol. per liter of curve 2 in the diagrams given of course, also, in the heaps local concentrations are usually very much higher than this, which is also true of the effluent li-quors, so that I feel that it is safe to say that copper is already present in amount sufficient to realize, as large an accelerating effect as is practicable. Too much im-provement or refinement cannot be expected in a method of this kind, due to commercial limitations. It should be remembered that chemically and physically there is no sharp dividing line between leaching in place, heap leaching, and the usual tank leaching practice, practi-cally the same reagents being used in all three. From the viewpoint of extractions, etc., it is not common sense to apply leaching in place to an orebody carrying enough copper to pay for mining; and the same is true of heap leaching, for an ore carrying enough to pay for the crushing, handling, etc., of ordinary leaching. That is to say, leaching in place should properly be consid-ered only for an ore too low-grade to pay for mining, and heap leaching for the next higher grade, still how-ever too low-grade to pay for crushing and other re-finements. There is no advantage in leaching without mining or in heap leaching except lower cost of in-stallation and handling; on the other hand there are very distinct disadvantages which are inherent and which should prohibit their use except where necessity requires. The object of metallurgy is to make money out of the handling of ore, and it is purely a question of money as to how far we can go in "improving" or

Jan 7, 1927

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969