Search Documents

By R. E. Fryxell, E. C. Duderstadt, P. K. Conn

Permeation rates for nitrogen through are-cast tungsten were measured in the temperature range 1800° to 2600°C at nitrogen pressure differentials of 1.0 and 0.1 atm. Gas chromatography was used to measure the quantities of nitrogen which permeated through 0.26-and 0.53-mm-thick membranes. Permeation rates were proportional to the difference between the square roots of the nitrogen pressure on each side of the membrane and inversely proportional to membrane thickness, indicating that atomic nitrogen was the difjusing species and that diffusion was the rate-limiting step of the process. Permeation coefficients calculated from the rates may be represented by the equation: where P is expressed in the units cu cm (stP)-mm per 1/2 sq cm-min-atm"' and 70.0 * 0.8 is the activation energy in kcal per mole of permeating species. In a previous paper' permeation rates were reported for hydrogen and for oxygen through tungsten. The permeation cells used for the hydrogen measurements were suitable for measuring nitrogen permeation under similar conditions, so the study was extended to include nitrogen. Permeation rates of nitrogen through the polycrys-talline arc-cast tungsten membranes were measured in the temperature range 1800" to 2600°C using two membrane thicknesses and two nitrogen pressure differentials. Permeation coefficients were calculated and the activation energy of the process determined. THEORY For diatomic gases which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at an elevated temperature where bulk diffusion is the rate-limiting step of the process is given by the equation: where: q = total amount of gas permeating a membrane, P = temperature-dependent permeation coefficient, A = area of membrane, t = time, p1 = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, and d = thickness of membrane. When bulk diffusion is the rate-controlling step, and the solubility of the gas obeys Henry's law, a further relationship is that, for any given temperature and pressure, the permeation is the product of diffusivity and the amount in solution. The permeation coefficient, P, is temperature-dependent according to the equation: where: Po = permeation constant, Q = activation energy, R = gas constant, and T = absolute temperature. EXPERIMENTAL PROCEDURES Cell Design and Experimental Apparatus. Two of the permeation cells used for the previous measurements of hydrogen permeation are shown in Fig. 1. Each consisted of a cylindrical chamber divided into two parts by a permeation membrane fabricated from high-purity (>99.9 pct W) wrought tungsten sheet made from vacuum arc-cast tungsten. The membrane in one cell was 0.26 mm thick and the other was 0.53 mm. The fabrication of these cells was described previously.' The permeation cells were mounted vertically in a high-temperature tungsten resistance furnace and the membranes and the center portions heated to test temperatures. Temperatures were measured by sighting an optical pyrometer on the edge of the membrane through a small hole in a tungsten plate which was fastened to the side of the cell. This arrangement provided an approximate black-body condition and eliminated the need for emittance corrections. Appropriate corrections were made for the quartz window through which the temperatures were measured. Argon gas flowed through the 10-liter volume of the furnace at the rate of 4.7 liters per min. An impurity

Jan 1, 1969

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By John Hays Hammond

This is an era of "expansion;" and, conformably with the change in commercial conditions, the function of the mining engineer, as well as that of his confréres in many other professions, has also expanded. From the position of an engineer, limited to the determination of technical questions, the engineer of to-day has come to assume an economic importance in those branches of industry dependent upon engineering skill for their development. He is indeed an engineer of limited usefulness who does not go further professionally than to submit a purely technical report on subjects presented for his consideration. While he has the same responsibility as formerly in the solution of the technical problems involved, he is further expected to supplement his report with advice on the financial and commercial aspects of these problems. For the great majority of problems presented to the engineer ultimately involve the determination of the pecuniary relations of the propositions under consideration. The great corporation lawyer no longer earns his fee by merely submitting his opinion as to the legal issues involved in law-suits affecting the corporation; he now assumes charge of the entire legal work, including both the organization of the corporation and the maintenance of its legal status thereafter. In like manner, the engineer, whose report was, as I

Jan 1, 1909

By E. Baker, David Donoghue

Legal and legislative matters constituted the outstanding features of proration in Texas in 1932. From East Texas emanated most of the political, legal, technical and industrial activity. Conroe and Thompson developed into fields of major importance. Proration orders were issued by the Railroad Commission on many of the producing fields of the Gulf Coast and West Texas not covered in previous years. In Yates, Penn Pool, Winkler, Van, the Panhandle, North Texas and West Central Texas there were 110 changes of importance, except in allowables. New proration schemes were introduced in East Texas, Conroe, Thompson, Saranosa, Government Wells, Tuleta and Howard-Glasscock. Little progress was made in administration or technical development. Legal and Legislative Matters Proration first began in Texas in 1927 as a voluntary attempt to divide the market outlet of a field on an equitable basis. The statutes then in existence were considered somewhat archaic and the Railroad Commission's authority was limited. Subsequent efforts to strengthen the laws were not wholly successful. The 1929 Conservation Act made no mention of market demand but declared that the term "waste" did not mean " economic waste." With the passage of the Pipc Line Act of 1930, providing for ratable purchasing, it was the opinion of many lawyere that a legal means of proration had been found. The 1931 law had ths same provision as that of 1929 with respect to economic waste but specifically prohibited limiting of production to market demand. The law passed Nov. 12, 1932, omitted reference to economic waste and specifically provided for limitation of production to reasonable market demand. Vigorous attacks were being made in State and Federal Courts on the constitutionality of the laws and the validity of the Commission's orders. In Peoples Petroleum Producers, Inc. et al. vs. Lon A. Smith et al., which had been heard before a three-judge U. S. District Court in Houston on May 28, 1932 and again on Sept. 19, the Court's decision for plaintiffs, released Oct. 2, influenced in a large measure the calling of the Legislature and the passage of the Market Demand Law on Nov. 12.

Jan 1, 1933

By John N. Dew, William L. Martin, `

This paper describes the results of a laboratory investigation conducted to obtain data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. Air and fuel requirements, rates of advance, com-bustion temperatures, and coke and fluid distributions are presented. The mechanism of oil recovery by in stiu combustion is discussed. Five crude oils ranging in gravity from 10.9 to 34.2"' API were prodrrced from a semiadiabatic, uncon-.solidnted sand pack by in situ combustion. Experimental conditions were varied over a wide range in order to determine the inter-relation-.ships of process variables. The mini-mum air flux requirement for self-sustained combustion was found to he less than 10 scf/hr-ft'l. The rate of advance of a self-sustained combustion zone was found to be nearly proportional to the air flux at the combustion front. The effects of presrure and injected air flux were studied in a series of experiments using a 21.2" API crude. A minimum air require-ment was observed at an air .flux of 20 scf/hr-ft'. The oil saturation con-sumed as fuel averaged 5.5 per cent of pore volume. The effect of air pressure was, found to be .small for experiments having high combustion eficiencies. This study should promote a better understanding of the problems and mechanisms involved in labora-tory investigations and field applications of the in situ combustion pro-cess. The data presented will be use- ful in the interpretation of results of field tests. When tempered with volu-metric sweep efficiencies, the data can be used in making preliminary economic appraisals of the process as applied to reservoirs containing high porosity unconsolidated media. INTRODUCTION The purpose of this work was to obtain laboratory data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. In situ combustion basically consists of (1) injecting air into a reservoir through selected input wells to create an air sweep through the reservoir, (2) igniting the crude at the injection well, and (3) propagating the combustion front through the reservoir by continued air injection. By this means, oil is swept toward producing wells in the area. The fuel for combustion is supplied by heavy residual material (coke) which has been deposited on the sand grains during distillation and cracking of the crude oil ahead of the combustion front. Recovery of petroleum by a combustion or heat wave process is not a new idea. F. A. Howard was granted a patent in 1923 on a process in which air and a combustible gas were pumped into an injection well and ignited.' Russian engineers reported on field experiments with a crude oil gasification process in 1935'. Other known early field tests include those conducted near Bar-tlesville and Ardmore, Okla., in 1942." More recently completed field tests include an inverted seven-spot by Sinclair Oil Co. in the Delaware-Childers field, Nowata County, Okla.'; a three-well and an inverted five-spot test by Magnolia Petroleum Co. in Jefferson County, Okla."."; and a test by California Research Corp. in the Irvine-Furnace field in Kentucky. The Worthington Corp. has completed a test in cooperation with the Forest Oil Corp. in Clark County, 111.l Several field tests are now in progress. Sinclair has acquired a 600-acre lease in the Humboldt-Chanute field, Allen County, Kans., and is under way with a large-scale operation. Three field tests are under way in California. The General Petroleum Corp. is conducting an inverted five-spot pattern test in the South Bel-ridge field in Kern County under a cooperative agreement with 11 other companies, including Continental Oil Co. California Research Corp. is conducting a four-well pattern test in Midway-Sunset field near Maricopa, and Richfield Oil Corp. is under way with a test in the Ojai field in Ventura County. Although the published information is valuable concerning results of field tests, little laboratory data other than that reported by Kuhn and Koch5 are available to aid in appraising the tests from a technical or economic standpoint. Engineering data needed to evaluate the process include the amount of air required per barrel of oil recovered, minimum injection rates which will support combustion, rates of advance, air required per unit volume of reservoir cleaned, amount of oil recovered, and amount of oil consumed as fuel. The present laboratory investigation was undertaken to provide these data for that portion of the reservoir swept by the combustion zone. The first phase of this investigation was exploratory in nature and was conducted at injection pressures less than 100 psig. Data were ob-

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heating at 200°C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. Materials and Methods The work was done on high grade electrolytic copper, 99.942 per cent. copper plus silver, silver 0.0008 per cent. It was hot-rolled to >/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire 'were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By Howard H. Fields

Any mining engineer with a desire to operate independently, with some financial backing, and with no fear of heavy responsibility and long hours, should be able to make a comfortable living in Mexico. Barring a few inconveniences such as a lack of satisfactory liability or accident insurance, the difficulty of obtaining repair parts or vehicles, and the length of time required to receive returns from shipments, the operation of small mine is not at all difficult. It is, in fact, a little easier to find a good prospect in Mexico than in the U.S.

Jan 1, 1950

By S. S. PRENZ

Discussion held at the sessions of the Canal Zone meeting, November, 1910. [SECRETARY'S NOTE.-As a result of this discussion, an expression of opinion covering all points of unanimous agreement was adopted and signed by members of the Institute party as individuals. This statement, which was printed in the Bulletin of December, 1910, is reprinted below, as an introduction to ,the detailed report of the discussion. It should be clearly understood that it does not constitute an official declaration by the Institute, the rules of which forbid any such action. At the New Haven meeting of February, 1909, a free discussion of the plan of the canal took place, in which the critics of the present scheme had full opportunity to state their views. That discussion was continued at considerable length in the newspapers ; but the Institute was never committed to either side. In this latter instance, the situation is precisely similar. Certain members and guests of the Institute, having had the advantage of later developments and of personal inspection, have expressed the conclusions at which they have arrived on their own responsibility ; and these conclusions are published by the Institute, subject to further discussion, like any other part of its proceedings. The general statement referred to contained a promise that the full discussion, of which it was a result, would be subsequently printed ; and this promise is fulfilled, so far as practicable, in the subjoined report, concerning which I beg to offer the following explanations: 1. It is made up of the remarks of the members of our party, as subsequently written out and mailed to the Secretary. 2. In editing these contributions, I have condensed the material considerably by cutting out much repetition of opinions and phrases ; and in such excision, I, frankly confess, the authors whose communications were delayed, have been the sufferers. Nevertheless, there is a good deal of repetition left, as there must be, when so many persons had talked so much, and come to agreement upon so many points. 3. It has been found impossible to preserve in this report the actual order of the free and informal oral discussion represented. Consequently the several contributions have been arranged in alphabetical order under the names of their authors. References to "preceding speakers," etc., must therefore be construed as referring to other speakers, preceding or following.-R. W. R.] S. S. PRINZ AUGUST WILHELM, AT SEA, November 14, 1910. We, the undersigned, members and guests of the American Institute of Mining Engineers, after a visit to the Isthmus of Panama, and inspection of the work of the United States Isthmian Canal Commission, and after full discussion of our individual impressions, find ourselves in unanimous agreement as to the following conclusions:

Jan 1, 1911

By John Hays Hammoud

At the Annual Business Meeting of the Institute, held February 19, 1907, the following persons were elected Council. President of the Council, John Hays Hammond, New York, N. Y. Vice-Presidents (for two years), Samuel B. Christy, Berkeley, Cal. ; John A. Church, New York, N. Y.; Persifor Frazer, Philadelphia, Pa. Councilors (for three years), B. F. Fackenthal, Jr., Easton, Pa.; H. 0. Hofman, Boston, Mass.; Walter Renton Ingalls, New York, N. Y. Secretary. of the Council (for one year), Rossiter W. Raymond, New York, N.Y.

Mar 1, 1907

By AIME AIME

A LUSTY baby of the Institute, the Coal Division, showed that it had acquired a full set of teeth and was capable of man's work at the Division meeting at Fairmont, W. Va., on March 26 and 27. At this second of a series of field meetings, the first of which was held in Pittsburgh last fall, the industry in the East was represented from top to bottom and good humor and enthusiasm were the predominant notes. West Virginians are always good hosts and this meeting would have proved the statement to any inclined to doubt it. The spacious auditorium of the Fairmont Hotel was arranged for the technical sessions, the hotel being headquarters for the meeting. About a hundred and twenty-five representatives were registered and in attendance when Thomas G. Fear, chairman, opened the morning session at 10 o'clock Mr. Fear first introduced Howard Eavenson, vice-chairman of the morning program, who, as chairman of the Coal Division, had labored long and cheerfully to make the meeting successful. Mr. Eavenson talked briefly on what the organization was doing, pointing out that these field meetings were designed to bring the members into closer touch with the parent Institute and give the younger engineers in the field a better opportunity to participate in the work the Institute is doing. He congratulated the various committees for their work in promoting the meeting.

Jan 1, 1931

By E. G. Dahlgren, Dan O. Howard

THE West Edmond oil field, which covers parts of Oklahoma, Canadian, Kingfisher, and Logan Counties in the State of Oklahoma, is in geographical extent the largest single oil field found in the state. At the present time, its area of 26,800 acres is almost twice as large as the Oklahoma City field, which hitherto was the state's largest field. Many authorities believe that the West Edmond field is the most important oil pool found in the United States since Pearl Harbor. The discovery of the field without the help of geological, geophysical, or other recognized technical information, the fact that the oil and gas accumulated in a stratigraphic or wedge-type trap, and the rapid development of the productive area under wartime conditions are some of the interesting features of the field. The West Edmond field lies west of the Oklahoma City, Britton, and Edmond fields. The field is in an area that has been considered on the west flank of the Granite Ridge line of folding, on which a number of Central Oklahoma's most important oil fields are located. Over a period of years, especially since the discovery of the new pools such as Oklahoma City, Edmond, Britton, and Crescent, the general area of the West Edmond field has been explored intensively by geological and geophysical methods. This led at times to the drilling of a few dry Wilcox sand tests.

Jan 1, 1945

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By Pierre de P. Ricketts

Having had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

By Pierre de P. E. M. Ricketts

HAVING had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

Jan 1, 1876

By Chester A. Fulton

SUPPLYING as it does a necessity for healthy animal and vegetable phosphate production is a most important industry. We human beings also are animal as this war so surely proves. Unlike many other elements no substitnite is available for phosphorus or its compounds. Marvelous as are modern plastics none can lake the place of phosphorus in making hone structures. As meassured in these times the phosphate industry is not a large industry. Output of phosphate rock, the original source of our agricultural and ,chemical phophates amounts to only some twelve million long tons per annum in the entire world. Phosphates are compounds of phosphorus, which is always found in nature combined with other elements. It never occurs in nature as such. The first choice of the element phosphorus is tie itself strongly to oxygen and then to water moisture - thus becomeing phosphlic acid. This phosphoric acid in turn hunts around for a base such as lime for instance and together they make phosphate of lime.

Jan 1, 1944

By H. S. Munroe

The dressing-works of the St. Joseph Lead Company were destroyed by fire, February 26th, 1883. Within about four months, or on July 5th, 1883, the new mill, with a capacity of 500 tons per day, was built and in active operation. The capacity of the new mill has since been increased to 800 tons per day. The old mill was built in 1867, by Mr. C. B. Parsons, the present superintendent. It was a curious rambling old structure, which had grown with the demands of the business; a few jigs having been added in one place, a table or two in another and wings and sheds added to the main buildings, from time to time, as it was found necessary to increase the efficiency or the capacity of the mill. The old mill was, moreover, a most interesting place to the student, a perfect "museum of ore-dressing." Nearly every form of dressing apparatus known to the art had, at one time or another, found a place under its roof, jigs of many kinds, concave, convex, side-bump and stationary tables, tyes, buddles, dolly-tubs, etc., etc. The method of dressing followed in the main the lines of English practice, but with many modifications, both in the machinery and the methods of working, due to the inventive genius of Mr. Parsons. Different forms of crushing apparatus were tried, and the best method of handling the ore and the different products of

Jan 1, 1889

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work' the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,' Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

By R. E. Boehler, N. C. Ludwig

At Buffington Station, Gary, Ind., Universal Atlas Cement operates fourteen 8 x 10Y2 x 155-ft cement kilns in mill 6 and two 11 x 360-ft kilns in the Harbor plant. The No. 11 and 12 kilns in mill 6 are equipped with Manitowac recuperator sections. This report describes studies in measuring exterior shell temperatures on several of these kilns and the development of a traveling radiation pyrometer with certain novel features.

Jan 2, 1960