Search Documents

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

The function of a preposition is to show the relation of one thing to another; it is necessary therefore for the writer to select the preposition that indicates the particular relation, otherwise he will fail to express himself clearly. Is it against common sense &o suggest that a Government is justified, morally as well as constitutionally, in preventing the decay of an industry by insisting upon the amalgamation of the prosperous with the needy? All these seven prepositions are used correctly. With the first dredge introduced in Russia, of Werf Conrad, Haarlem, make, this method of alluvial mining became important. Here the prepositions "with", "in", and "of" are used wrongly. He means: "This method of alluvial mining sprang into importance shortly after the first dredge, made at the Werf Conrad, Haarlem, was introduced into Russia." The statement itself is not true, but for that I am not responsible. Once, while I was serving with him, we were frozen in out of sight of land in the Gulf of Pichili in the North of China. Admiral Fisher wrote thus. He has used nine prepositions in making this brief statement. The sequence of three prepositions "in out of" is particularly awkward. Lounsbury says : One might fairly infer from the way in which it [newspaper English] is often spoken of that with the steadily increasing circulation of this sort of periodical literature there is no hope whatever for our speech. "Of that with" is lamentable. The construction is thoroughly bad, and it is bad mainly because the misplaced prepositions have tangled the meaning. I suggest:

Jan 1, 1931

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

Jan 1, 1949

By R. G. Robins, O. J. Kwok

The application of chemical thermodynamic theory to high temperature aqueous systems is discussed as a basis for the explanation of thermal precipitation. The derivation of high temperature potential/ pH diagrams is briefly outlined in order to show a temperature/pH relationship for hydrolytic precipitation, which is an effect that is caused simply by heating an aqueous solution. Various examples of thermal precipitation are given, with particular reference to separation of metal values from leach solutions. Metal sulphate solutions are shown to precipitate basic sulphates, hydrated sulphates , oxides, hydroxides, and oxydroxides of the metal depending largely on the pH, the concentration of metal ion, and the concentration of sulphate or bisulphate. The CuS04-H2S04-H20 system is treated in some detail, and the separation of copper from other metal ions is investigated. Other separations involving Fe, Ni, Zn, Cd, and Cr are considered. Other advantages of thermal precipitation, such as the formation of high purity, large particle size and easily filterable materials, are presented. The kinetics of thermal precipitation are also briefly examined.

Jan 1, 1973

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

By Walter H. Ortel, George B. Wallace

INTRODUCTION A greater understanding is required about the factors which control tunneling operations if we are to meet the expected demand for tunnels. Much of the needed information can best be achieved by the proper use of instrumentation and advanced engineering concepts. Tunnel measurements and their analysis may prove to be the key which will give the insight necessary to understand the relationship of rock, tunnel supports, and linings. There are three main areas which can be improved through the use of tunnel instrumentation. First, and of prime importance, is safety for men and the project. When unstable conditions occur, sets become distorted. Even without measurements, it is sometimes possible to tell when trouble is approaching. In effect, the set acts as a load cell. Distortions in the set indicate reinforcements may be required to maintain stability. Additional sets or rock bolts, if they are placed soon enough, may provide this stability. However, when large rock displacements occur in short periods of time, it could be too late. Figure 1 is an example of the difficulties encountered in stopping moving rock. To stop the movement and possible failure, large props were placed above the spring line and the massive concrete gravity buttress was constructed along the legs. Rock bolts from the buttress deep into the rock were also used in an attempt to stabilize the rock mass. However, this work is for a highway tunnel and eventually these props and buttresses must be removed.

Jan 1, 1971

By Ronald E. Versaw

Environmental legislation, both existing and proposed, requires that mills, tailings dams, evaporation ponds, and related processing facilities be located, constructed, and operated within stringent guidelines. An early step in planning a new processing facility is performing a site selection study in which topographic, hydrologic, geotechnical, and environmental parameters are evaluated for several alternate sites. Once a site is selected, then an environmental report, including a description of the proposed action, alternatives, baseline surveys, and discussions of potential environmental impacts, mitigation measures and monitoring programs is required. The federal legislation, siting studies, and environmental studies (along with the implications of these as they affect design) are discussed. In addition, costs for performing these studies and implementing control of effluents are discussed.

Jan 1, 1978

By Robert Corcoran, George Wiener

A study of the orientations and microstructure of 3 pct Si Fe alloys after deformation and recrystallization has been made. The components found after deformation agreed with recently published work on single crystals, being primarily (001) [110], (111) [110], and (111) {112}. A pronounced effect of temperature of recrystalliza-tion was found on microstructure and orientation. Low temperature recrystallization was interpreted in terms of low angle boundaries which resulted in the retention of a large amount of the deformation texture. High temperature recrystallization was interpreted in terms of high angle boundaries which gave rise to new components. No simple angular relation between the deformation and high temperature recrystalliza-tion textures could be detected. DEFORMATION and recrystallization behavior of 3 pct Si-Fe has been the subject of scientific investigation for many years. The fact that it is a single phase body-centered-cubic alloy from room temperature to the melting point permits study over a wide range of temperature without the complications of phase transformations. There is an important commercial interest in this material as well, since it is widely used in the electrical industry. In the present work the deformation and recrystallization behavior of poly crystal line silicon iron has been studied with the primary purpose of evaluating the effect of a second phase impurity on both processes as well as the effect of temperature on the recrystallization characteristics. With regard to deformation, the emphasis has been placed on a study of the crys-

Jan 1, 1957

By V. Vahatalo, E. Hakapaa, H. Tanner

Recently modernized, the surface plant of the Outokumpu mine in Finland incorporates a number of ideas meriting close scrutiny from this side of the Atlantic. The mining methods make extensive use of concrete in some unusual ways. Design of the headframe and surface plant represents the latest thinking of European engineers and includes an integral Koepe hoist. The deposit is in eastern Finland, province of North Karelia, 30 miles west northwest of Joensuu and at 60'44' N, latitude. Pyrrhotite, pyrite, chalcopyrite, and sphalerite mineralization occurs in a shear zone in quartzite near a body of serpentinite. Two lenses have a total length over 12.000 ft, with remaining reserves of the 3 to 4 pct Cu ore estimated at about 15 million metric tons.

Jul 1, 1955

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan' obtained kinetic data for the reduction of hematite spheres sintered at 13'70°C (2498'F'). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph' and Edstrom' that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By R. E. H. Pomeroy

EARLY in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (1) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application; the coal and air mixture can be piped where needed. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins.

Jan 2, 1920

By Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as sand-cast and as heat-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brinell and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. THE demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.1 Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergranular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about-950° F., quenching in oil or in cold or boiling water, and artificially aging

Jan 7, 1925

By A. F. Meston

Centrifugal force has been used for centuries for separating liquids but machines for doing this are a comparatively recent development. The use of these machines is being extended into many industries but this paper is confined to their use in the oil industry. The centrifugal machine is found at the well where "cut oil" is dehydrated for acceptance by pipe lines; and in the refinery and byproduct plant. In fact, wherever finely divided suspended particles should be removed from an oil, there is a possible use for a centrifugal machine, if the particles have, or can be made to have, a specific gravity different from that of the oil. Centrifugal machines are also used for cleaning fuel and lubricating oils and dehydrating transformer oils. Applications and Results When oil comes from the well mixed with water, it is spoken of as cut oil. Settling often does not remove sufficient water for the oil to be accepted by pipe lines, thus necessitating chemical or other treatment. Centrifuging alone, or following chemical treatment, effectively prepares such oil for pipe lines, as is shown by the following data: WateR, Etc. Wat~R. Etc. Temperature, Oil to Pipe Line, aT StUt at Finish Degrees F. Bel. Per HouR PIE Cent. PEECent Oklahoma lease.... 160 10 10 0.25 Kansas lease....... 125 4 20 0.25 to 2 On the Oklahoma lease, the machine was cleaned of solid material once in 12 hr. At first, it was thought that chemical treatment was necessary to start separation and 1 qt. of prepared compound was added to each 100 bbl. of the cut oil before centrifuging. Later it was found that

Jan 1, 1924

By Roy E. Thomas

Soon after the Waelz p1an.t for the fire concentration of low-grade zinc ores was put into operation in the early part of 1929 at Katowice, it was found that the conveyor equipment for transporting the hot residue from the furnace dust chambers was inadequate. Hand tramming with water cooling was used for a time, but that method was injurious to the workmen as well as costly. The problem was to find some practical mechanical means of conveying flue dust at temperatures of from 450" to 600°C. as it was drawn from the dust chambers. After considerable preliminary investigation it was decided to install pneumatic equipment for conveying the hot materials to a central mixing plant, where it would be mixed with slime and from which it would be returned to the furnace feed hoppers. The first pnenmatic equipment was installed in 1930, and has been in successful operation since that time. The pneumatic method of transportation has shown a considerable saving in operating costs over the former methods of dust handling and a decided improvement in working and hygienic conditions at the plant, through the elimination of the dust hazard. Additional pneumatic equipment mas installed in 1933 for conveying the furnace fume from the baghouses to the roaster plant. At the same time pick-up lines were provided for collecting the cleanings from the vertical and horizontal cooling pipes that are between the furnace dust chambers and the baghouses. The latter installation has practically eliminated a dusty and costly hand-tramming operation. A third extension was made to the pneumatic system in 1938 for conveying 'the zinc-lead-cadmium fume from the roaster-plant baghouses and flues to a new re-treatment plant for secondary products. The success of pneumatic conveying at the Waelz plant was the determining factor in the decision to install another pneumatic unit at the Saeger zinc-roasting and sintering plant. The new unit at Saeger was installed early in 1938 for the transportation of flue and Cottrell dust, small amounts of flotation concentrates to the sinter machines, and

Jan 1, 1944

By G. W. Nabor, M. Mortada

The effects of anisotropic or directional permeability on the areal sweep efficiency and the flow capacity are examined. The paper points out the importance of taking directional permeability into consideration in planning a flood. It analyzes the two-dimensional flow pattern associated with the skewed line drive for a unit mobility ratio. The direct and staggered line drives are treated as special cases of the skewed line drive. Analytical expressions are developed for the areal sweep efficiency at breakthrough and the flow capacity. They are related to the spacing between like wells, the distance between a row of injectors and the nearest row of producers, and the degree of skewness of the line drive. The latter quantity is defined such that it is equal to zero for the direct line drive and equals one-half for the staggered line drive. The areal sweep efficiency and the flow capacity depend also on the orientation of the flood pattern with respect to the principal axis of anisotropy. The paper provides a simple method for determining the areal sweep efficiency and the flow capacity for a formation in which the permeability in the bedding plane is anisotropic. INTRODUCTION Directional or anisotropic permeability is manifested by the ability of the formation to conduct fluids more readily along certain preferred directions. This situation occurs in many producing formationsl-4 and is usually attributed to depositional features in which the sand grains are oriented in a preferred direction. In some cases it results from the formation of a major and a minor fracture system. 4 Directional permeability should be taken into account in many phases of the production and exploration activities. Recognizing its existence in the formation of interest and planning accordingly can lead to increased recovery and substantial savings. For instance, the areal sweep efficiency in a water flood depends to a great extent on the orientation of the flood pattern with respect to the principal axis of permeability. Anisotropic5 permeability is specified by the directions of its three principal axes and the permeability along each axis. The principal axes of permeability are mutually perpendicular. This paper deals with the areal sweep efficiency at breakthrough and the flow capacity for formations with aniscltropic permeability. The flood pattern considered consists of alternate rows of injecting and producing wells. The rows of wells are parallel and form a developed, skewed line drive which is illustrated in Fig. 1. The staggered and direct line drives are treated as special cases of the skewed line drive. PRELLMINARY CONSIDERATIONS The formations considered in this paper are assumed to be of uniform thickness and porosity. The permeability is uniformly anisotropic, with each principal axis of permeability maintaining

ALTHOUGH iron ores occur in many parts of Sweden the two principal deposits are those at Grängesberg (see accompanying map) and at Kiirunavaara-Gellivare. Both of these deposits are con-trolled by a holding company, Trajikaktiebolaget Grängesberg-Oxelösund, which sells annually about one-half of, the iron in ore traded in world markets and has a fleet of 24 seagoing ore boats, with a total dead weight capacity of 172,500 tons. Because of its pre-eminence in international iron ore trade a brief outline of its operations will be of interest. ORE DEPOSITS OF GRÄNGESBERG The Grängesberg deposits have been known since the Middle Ages, but up to the middle of the nineteenth century the ore was transported from the mines to the furnaces in winter in. sleighs. Railway building began in 1853, and in 1873 the complicated structure of capital investment was tottering, but the basic bessemer process created a demand for ore high in phosphorus, as this is, and refinancing on the initiative of Sir Ernest Cassel put the principal operation on a firm footing. There are numerous property owners in the district, but they are all controlled by a joint administration board, and 90 per cent of the ore is produced by a subsidiary of the Grängesberg company from proper-ties which it either owns or leases. The ore, a mixture of magnetite and specular hematite, is in lenticular bodies, dipping about 70 E. in. fine-grained gneiss, and contains about 61 per cent Fe and 1 per. cent. P. There are two principal veins; the total ore reserves to a depth of 500 meters are estimated at 150,000,000 tons. As seen in the accompanying illustration, the ores were first worked in open cuts, but eventually underground shrinkage stoping was adopted. Difficulties were encountered in the support of the workings and from the freezing of the ore in the stopes, so slicing was adopted, although block-caving is used in one place. Most of the mining is now done at a depth "of 150 to 190 meters. The present annual output is about 1,400,-000 tons of crude ore, which yields about 1,000,000 tons of concentrate after being subjected to magnetic con-centration and jigging.

Jan 1, 1927

By R. W. Raymond

In a former paper (Trans., xvi., 770) I gave the text of the archaic mining law of the State of New York, together with some comments upon its curious provisions. In that connection I pointed out two facts : first, that the law seemed to have originated in the schemes of private parties, who were satisfied with those parts of it which concerned them particularly; and secondly, that the remaining provisions had been hitherto quite inoperative, for the reason that mines of the character to which they referred had not been discovered in the State. Since 1888, when that paper was written, the New York Legislature has passed several acts relating to mines as follows: 1. Chapter 394, Laws of 1890. This provides for an inspection

Jan 1, 1895

By F. Peter

Technical progress takes place in two directions: the improvement of methods, affecting the quality of the product; and increase in the economy of operations, affecting its cost. In the iron-industry, practice is pretty well settled, and revolutionary changes of method are, for the present, not to be expected. Hence, in this industry, the principal endeavor is to reduce costs by the use of labor-saving inventions, such as the machines brought into use during the last decade. But it is not alone necessary to reduce the labor-cost; complete economy requires also a saving in raw material. Under this head we may rank the coal employed as metallurgical fuel; and it follows that progress includes the economic use of fuel, so managed as not to injure quality of product. In the present paper it will be shown how, by suitable utilization of the heat from the furnace, a large portion of it may be made available for other purposes. Such utilization of waste-gases is important in all industries which employ furnaces (especially heating-and smelting-furnaces); and in the first rank of these stand the iron-, glass-, and porcelain-manufactures. The following pages are devoted chiefly to the waste-gases of smelting-works, and especially to those reverberatory-furnace gases which are not combustible.' The object of metallurgical furnaces is either to fuse the material charged or to bring it to a high temperature required for further mechanical manipulation. Leaving out of consideration for the present the reverberatory fusion-furnaces, we have to do with the heating-furnaces employed in connection with rolls, hammers, or hydraulic presses. The temperature to which the material must be

Jan 1, 1914