Search Documents

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the virgin condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 69 to 258 MPa producing rupture times varying from 8 to about 4908 h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results mentioned in literature for the same material in the virgin condition.

Aug 16, 2017

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Willy Ank de Morais, Márcio de Morais Tavares, Érika Elis Kuo, Guilherme Bernardo da Silva, Marcelo Costa Choukri

Furos não planejados são comumente executados em vigas sem as devidas precauções no momento de sua execução. Para se realizar um furo sobre um elemento estrutural, deve-se realizar primeiro um planejamento, para então definir os critérios de efetivação e dimensionamento estrutural conforme a NBR 6118:2014, já que tais furos podem acabar interferindo no comportamento estrutural da viga. Deste modo, o presente trabalho tem como proposito o estudo da influência dos furos nas vigas de concreto armado a fim de analisar se o elemento estrutural sofre uma perda na sua resistência pelo fato do furo não ter sido planejado no momento do dimensionamento da viga. Para a realização deste trabalho foram dimensionadas três vigas de concreto armado e executados os furos com as vigas carregadas e posterior análise das fissuras geradas na região dos furos. Para validação dos resultados obtidos todas as três vigas foram construídas e ensaiadas nas dependências da Universidade UNAERP. Os furos possuíam um diâmetro de 50mm e mesmo ocorrendo perda de área de aço em algumas vigas, estes não introduziram influência relevante na resistência das vigas.

Mar 1, 2019

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Odair Mauricio Machado

A implantação do LIMS (Sistemas de Gerenciamento de Informações de Laboratório) surgiu da necessidade do Laboratório ArcelorMittal Vega se atualizar tecnologicamente afim de melhorar rastreabilidade de informações e sistematizar a execução de atividades dentro do Laboratório. Os colaboradores destinavam muito tempo à manipulação de planilhas utilizadas no armazenamento e controle das análises, deixando o negócio vulnerável aos requisitos da Norma ISO / TS 16949 em todo o Laboratório. Anterior ao sistema, todo o cadastro, controle e gestão dos ensaios eram realizados em planilhas, que são mantidos pela equipe do Laboratório. Os maiores impactos no uso das planilhas são caracterizados pelos erros de transcrição de dados e cálculo manual de resultados nas diversas etapas do processo, potencializando assim a incidência de erros e muito tempo dos colaboradores envolvidos na gestão dos documentos. O trabalho demonstra o processo de implantação do LIMS no Laboratório, sua integração com equipamentos de analise e sistema de Nível 3, além de benefícios alcançados em termos de confiabilidade, redução de tempo para análises e benefícios para sistema de qualidade.

Oct 30, 2017

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Rossana Bezerra de Azevedo Vasconcelos Seabra de Melo

O presente estudo apresenta um método de avaliação de desempenho de operadores nas análises químicas que caracterizam o minério de ferro. São eles: Ferro total (Fe), sílica (SiO2), alumina (Al2O3), manganês (Mn), fósforo (P) e perda por calcinação (PPC). O desempenho é avaliado em termos de precisão e veracidade. Estes dois indicadores primários são combinados num secundário denominado de indicador de “confiabilidade metrológica”. O método foi aplicado nos laboratórios da Mina (no estado do Pará) e do Porto (no estado do Maranhão) de uma empresa mineradora onde foi possível: 1) conhecer o desempenho de cada laboratório assim como conhecer o desempenho de cada operador; 2) identificar os pontos fortes (identificar o procedimento que leva a melhores desempenhos) e oportunidades de melhorias (atuar nas causas, capacitar); 3) equalizar a forma de executar cada uma das tarefas com as melhores práticas identificadas; 4) proporcionar oportunidade de desenvolvimento técnico dos profissionais envolvidos no processo. O desempenho neste indicador tornou-se critério avaliação de aptidão para executar análises.

Aug 2, 2018

By Edgar Apaza Huallpa

Os aços inoxidáveis duplex (AID), apresentam em geral uma microestrutura composta de austenita e ferrita em proporções aproximadamente iguais. Para ter o controle dos processos de fabricação e desempenho é importante conhecer sua evolução microestrutural, devido à precipitação de fases intermetálicas como sigma (s) e chi (?), que causam grave deterioração das propriedades mecânicas do material. Neste trabalho foi estudada a evolução da fase sigma (s) durante tratamentos térmicos em temperaturas intermetálicas (800°C-900°C) de amostras do aço inoxidável duplex tipo SAF2205 (DIN 1.4462/UNS 31803). Foi observada uma gradual redução da intensidade do sinal do ruído de Barkhausen com o aumento do tempo de tratamento térmico, indicando uma redução na fração de fase ferromagnética. Para tempos de tratamento de 24 horas, o sinal de Ruído de Barkhausen está quase totalmente inserido dentro do ruído de fundo da medida, indicando haver uma fração volumétrica bastante reduzida de ferrita. Por meio da produção de amostras padrão para calibração, essa pode ser uma via de avaliação não destrutiva de componentes submetidos em campo a temperaturas nas quais se formam fases intermetálicas.

Aug 8, 2018

By Igor Martins dos Santos

O nitrogênio waste, que é chamado assim por ser mais impuro, devido à existência de uma porcentagem aproximada de 2% mais de oxigênio no mesmo, utilizado exclusivamente no processo de “Slag Splash” na Aciaria, possui um contrato fechado de volume para fornecimento (7.000 Nm³/h, à pressão de 30 bar), o qual estava sendo utilizada aproximadamente a metade do mesmo (3.500 Nm³/h). Como no processo produtivo da CSA, é utilizado o nitrogênio de baixa pressão (16 bar) em grande quantidade (21.600 Nm³/h, sendo aproximadamente 5.600 Nm³/h acima do contrato de fornecimento), foi feito um projeto para interligar as duas linhas de nitrogênio através de aproximadamente 420 metros de tubulação, com sistema de controle integrado e analisador de oxigênio para garantir a concentração mínima de 1% de oxigênio no Nitrogênio de baixa pressão, devido à necessidade de algumas áreas. Nos primeiros seis meses após implantação, foi contabilizado uma economia de aproximadamente R$4.0 milhões (aproximadamente 3.100 Nm³/h de consumo).

Oct 30, 2017

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Claudio Fabbro

The increasing demand of wire rod high carbon grades for both small and large sizes are challenging the wire rod producers to enhance new technologies by combining high plant productivity and efficiency of superior quality finished products with extreme process flexibility. The possibility to change process route according to the final application of the rolled steel grade and to simplify production planning is one of the most important keys to success that distinguishes the mill plants developed by Danieli. This paper will focus on the most important metallurgical and process targets and on the in-line heat treatment technologies representing the core of Danieli know-how on high carbon grades production.

Jul 30, 2018

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017

By Adriano de Assunção Rodrigues, Gustavo Henrique Pinto de Oliveira, Wemerson Junio Gandra

O processo de obtenção de coque em uma coqueria convencional Non-Recovery consiste no aquecimento de uma mistura de carvões, provocando sua desvolatilização, gerando o coque que é principal combustível utilizado em altos-fornos. O aquecimento da mistura de carvões se dá de forma indireta. As paredes dos fornos recebem calor da câmara de combustão alimentada por uma mistura de gases de alto-forno, coqueria e aciaria ou, exclusivamente pelo gás de coqueria. O gás de coqueria COG (coke oven gas) é composto basicamente de hidrocarbonetos e recebe tratamento para retirada de impurezas, alcatrão, sulfato de amônia e óleos leves. Os elementos residuais no gás, mesmo após o processo de tratamento são extremamente prejudiciais às tubulações de distribuição, formando compostos corrosivos, podendo ocasionar o colapso de tubulações, gerando acidentes, gastos com reparos e perda de produção. Neste contexto, o presente trabalho tem por objetivo apresentar os fatores que levaram a necessidade de substituição das tubulações principais de distribuição de gás no subsolo da Coqueria 3 da Usiminas Ipatinga, conferindo segurança ao processo e estabilidade operacional.

Oct 1, 2019

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019