Search Documents

By Severino Albani Junior

Descreve as atividades envolvidas no processo de inspeção e caldeiras de vasos de pressão instalados na usina ArcelorMittal Tubarão, localizada em Vitória - ES. Mostra que esses equipamentos possuem critérios rigorosos não somente para inspeção, mas também de fabricação e operação que necessitam obedecer a códigos de projetos e normas técnicas nacionais e internacionais com objetivo de garantir o funcionamento seguro. Aplica como ferramenta principal no suporte da gestão das atividades um sistema informatizado de manutenção, utilizado em toda usina. Utiliza como pilar na gestão das atividades de inspeção conceitos e ferramentas de planejamento, programação e controle e mostra a complexidade de fazer o controle dessas inspeções numa usina do porte dessa Siderúrgica, que possui uma planta industrial enorme tanto no tamanho, quanto no número de equipamentos e processos existentes. Destaca um grande avanço nos resultados obtidos na gestão das atividades de inspeção dos vasos de pressão e caldeira da ArcelorMittal Tubarão.

Aug 7, 2018

By Eustáquio Vieira Júnior, Welder Gomes Gonçalves

Os altos-fornos podem apresentar ocorrências de arrombamento e/ou avermelhamentos dos algaravizes, e esses têm como conseqüências: alto risco na integridade dos conjuntos joelhos/algaravizes, resultando em baixa segurança operacional; elevação brusca da temperatura interna dos algaravizes, causando avermelhamentos e/ou arrombamentos recorrentes por desgaste acentuado do revestimento refratário; necessidade de paradas emergenciais; necessidade de troca dos conjuntos de algaravizes por desgaste acentuado do perfil refratário. Uma possível causa relacionada com essas ocorrências pode ser a combustão no interior do algaraviz do carvão que foi injetado pelas lanças, causando desgaste do revestimento refratário e conseqüentemente avermelhamento e/ou arrombamento do conjunto. Para evitar esse tipo de ocorrência foi instalado sistema de monitoramento de fenomenos na zona de combustão. Esse sistema trabalha como complemento do diferencial de pressão dos algaravizes e o anel de vento. Nesse trabalho, são mostradas as características do sistema de monitoramento e suas particularidades e os resultados alcançados após a implantação dos sistemas no que se refere aos danos em conjuntos de sopro.

Oct 1, 2019

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Gabriela Olsson Schneider

O acúmulo de poliestireno expandido (EPS) em sua forma pós-consumo é atualmente um motivo de preocupação em termos de impacto ambiental. Desenvolve-se, portanto, diferentes formulações de uma resina veículo para tinta que aproveitam este material como matéria-prima, através da dissolução do mesmo em solventes de origem natural extraídos da casca de laranja, quais sejam o próprio óleo essencial e seu componente majoritário D-limoneno, e em C9 aromático, junto aos copolímeros termoplásticos ESBR, SIS, SBS e SEBS e óleo de soja epoxidado (ESBO) como plastificantes. Obtém-se, em diferentes formulações, um desempenho favorável à futura adição de pigmento e demais aditivos, em termos de compatibilidade, elasticidade e aderência avaliados conforme normatização nacional e internacional. Observa-se especial sucesso com o uso do copolímero SEBS e do ESBO como plastificantes, concomitantemente à eficiência semelhante dos três solventes utilizados, o que permite a substituição do C9 aromático por componentes de origem natural e residual.

Aug 16, 2017

By Sandro Griza

Este estudo trata da simulação numérica por elementos finitos de um conjunto de trilhos, talas e parafusos de fixação, com o objetivo de verificar as tensões que ocorrem no conjunto, devido às cargas solicitadas e aplicadas nas condições de apoios estabelecidas pela norma NBR MB 3076/1989, além de duas condições de aperto dos parafusos: pré-carga de 50% da tensão de escoamento e 90% da tensão de escoamento do parafuso. Os resultados mostraram que o efeito de aperto do parafuso é mais significativo na distribuição de tensões do conjunto do que o efeito da carga externa. O aperto do parafuso a 50 e 90% do escoamento provocou maiores valores de tensões de Von Mises distribuídas tanto no parafuso quanto na tala, ultrapassando o escoamento dos materiais. É recomendável considerar que os menores valores de torque podem facilitar o desaperto da porca na prática, devido às passagens da roda sobre o conjunto.

Aug 16, 2017

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017

By Emanuele Osto

In late 2013, the installation of the world's first application of a break-through technology for rail hardening was started at Baogang Iron & Steel (Group) Co. Ltd. in Inner Mongolia, China, one of world's leading rail producers. The "Injector Dualphase Rail Hardening" (idRHa+) system was developed by Primetals Technologies and Centro Sviluppo Materiali S.p.A. (RINA-CSM) a Technical Center headquartered in Rome, Italy. Baogang was a key partner, providing its large expertise of premiumrail producer, including its experience with existing offline technologies. With a design based on thermal, mechanical and metallurgical models, idRHa+ can apply customized cooling protocols, so to obtain the desired microstructure and hardness distribution across the rail head, with a high degree of accurateness and operation flexibility. idRHa+ can be installed in inline or offline configurations. During 2014, the system was successfully commissioned at rail mill #2 in the city of Baotou, Inner Mongolia, and entered the regular commercial production. This paper gives an overview of the key concepts behind idRHa+'s design, the progression of its commissioning and testing till the ramp-up to consistent industrial operation. Derived from idRHa+ research and experience, other water-cooling technologies are available for different applications such as: quenching & tempering of medium-large sections, control of distorsion of merchant bars, quenching of stainless grades for improving the resistance to corrosion.

Aug 16, 2017

By Walter Valery, Kristy Duffy, Alex Jankovic, Peter Holtham

Hatch’s Mine to Process Optimization projects integrate mining and processing strategies, minimizing operating costs and maximizing overall profit. The methodology involves ore characterization, blast audits, plant surveys, analysis of historical data, and integrated modelling and simulation of mining and processing. Blast designs are tailored according to ore type and the downstream process is optimized for the changed feed. This approach has increased throughput and minimized costs for many operations worldwide. The implementation of this methodology at an iron ore operation that faced challenges with increasing mining strip ratio and ore body mineralogy changes is presented in this paper. The larger stripping ratio increased mining costs and constrained the run-of-mine (ROM) delivery to the process plant. Process performance was affected as the ore mineralogy shifted from predominantly hematite to include greater proportions of magnetite. The project objective was to minimize overall cost per ton mined and processed and maximize profit. Tailoring the blast designs according to ore type and process optimization increased the throughput of all process lines. This provided the potential to shut down one of the five processing line, aligning the mine and plant capacity and significantly reducing the processing costs.

Oct 3, 2019

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By Virgínia Cruz Rangel Albuquerque e Lima

Nas últimas décadas, o silício grau solar (~99,9999% de pureza) tornou-se um importante material devido à sua aplicação na construção de células fotovoltaicas. O comportamento frágil do silício a temperatura ambiente dificulta a obtenção de formatos convenientes para as etapas posteriores de processamento. O presente trabalho tem o objetivo de analisar a fratura de lingotes de silício ocorrida durante o processo de lingotamento contínuo após fusão em forno de feixe de elétrons. A análise do silício obtido no lingotamento contínuo mostrou a ocorrência de fratura por clivagem. A fratura observada após o lingotamento de iniciadores de silício ocorreu na mesma região do lingote obtido no lingotamento contínuo, indicando que a força aplicada para extração do silício durante o lingotamento contínuo não causa a fratura, que, portanto resulta das tensões térmicas durante a solidificação e resfriamento posterior. A modelagem matemática através do método dos elementos finitos da transferência de calor combinada com a formação de tensões térmicas mostrou que as tensões térmicas resultantes do processo de resfriamento, após a solidificação, poderiam ser suficientes para causar as fraturas observadas.

Aug 8, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017