Search Documents

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By Diego José Inforzato

Hot tensile data were correlated with creep data, in Aluminum Alloy AL7475-T7351, as part of a broader research program, aiming at the validation of a methodology that proposes an equivalence between the two kind of results, for metallic materials in general. The methodology is based on a criterion that establishes correlation among the following parameters from each test: the strain rate, ultimate tensile stress, and time to reach the ultimate tensile stress, in tensile tests, are equivalent respectively to the: minimum strain rate, applied stress and rupture time, in creep tests, for a given test temperature. The present material was tested at 3 temperatures: 133,166 and 193ºC, using 3 nominal tensile strain rates in the hot tensile tests: 3.2x10-6, 1.6x10-4 and 6.4x10-3 s-1 and 9 applied stress levels in the creep tests, varying from 140 to 400 MPa. The conversion of the hot tensile data to creep-like data allowed performing the analysis of all the results together according to the traditional creep relations proposed by different authors, namely: Norton, Arrhenius, Zener-Hollomon and Monkman-Grant, with the determination of the corresponding parameters in each case. The equivalence between hot tensile and creep data is also confirmed for this aluminum alloy.

Aug 8, 2018

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017

By Saulo Brinco Diniz

As ligas de alumínio da série 7XXX são largamente utilizadas no setor aeronáutico devido sua alta razão resistência mecânica / densidade. O que proporciona uma alta resistência mecânica para as ligas da série 7XXX é a adição de elementos de ligas e tratamentos térmicos adequados, como por exemplo o T7351. Este trabalho teve como objetivo, estudar a evolução microestrutural de uma liga de alumínio 7475-T7351 processada por laminação convencional a temperatura ambiente, e posteriormente submetida a tratamentos térmicos de recozimento para recristalização. De acordo com os resultados apresentados, a amostra que foi submetida ao tratamento térmico de recozimento para recristalização a temperatura de 500ºC durante 15 minutos recristalizou, enquanto que a amostra que foi tratada a 350ºC durante 1500 minutos teve coalescimento dos precipitados.

Oct 30, 2017

By Vinícius de Souza Vilela

O presente trabalho tem por objetivo analisar o uso de filtros de alta pressão no tratamento de polpas decorrentes do beneficiamento mineral, em especial rejeitos e concentrados de mineração. Foram analisados os problemas da atual prática de deposição de finos em barragens de rejeitos e baias de decantação e os novos desafios encontrados pelo setor em relação a escassez de água e eficiência energética. São elencados os diferenciais tecnológicos implementados nos filtros prensa Matec e analisados os benefícios na aplicação desta tecnologia, tais como maior recuperação de água, redução dos impactos ambientais e redução dos custos operacionais para manuseio e disposição dos rejeitos. Por fim são analisados os testes de filtragem realizados com rejeitos e concentrados de minério de ferro.

Aug 16, 2017

By Gabriel Oliveira Glória

A sociedade cada vez mais está buscando por materiais ecologicamente corretos em detrimento de materiais nocivos ao meio ambiente. Nesse novo contexto as fibras naturais estão, cada vez mais substituindo as fibras sintéticas, por exemplo, a fibra de vidro. Além das vantagens ambientais, as fibras naturais são mais baratas do que os sintéticos. O ensaio de pullout estuda a adesão da fibra na matriz de poliéster e a interação das fibras com a matriz de poliéster, também chamados de biocompósitos. Portanto, o presente estudo analisou a fibra de PALF por meio de ensaio de pullout. O ensaio verificou que o comprimento de embutimento crítico da fibra de PALF em matriz de poliéster é de 1,20 mm e a tensão cisalhante na interface fibra/matriz é de 11,66 Mpa.

Oct 30, 2017

By Eddy Dierckx

Modernization of flat rolling plants is essential to sustainably fulfill increasing market demands and to improve competitiveness. Intelligent modernizations ensure getting maximum prime yield of existing mills, even if they have gone through half a century of operation. Existing mills were designed based on former production, consumption and quality targets. Ever increasing requirements such as increase of productivity, change of product mix (e.g. new steel grades), reduction of energy consumption and improvement of product quality lead to the necessity to adapt the existing equipment to the new target. SMS group provides, besides the reliable equipment and automation solutions to successful upgrades of existing mills, also a systematic approach to develop technical and economical solutions together with our customers (conceptual engineering). This paper describes the SMS group approach to modernizations / upgrades, introduces powerful performance modules and provides a number of successful examples that have been implemented recently.

Aug 17, 2017

By Lukas Pichler

The market trend of advanced high strength steel (AHSS) with demand for higher strength products is increasing continuously. The inline cooling technologies have established as the most powerful metallurgical tool to achieve these demands. However, the cooling capabilities of existing hot strip mills, plate and Steckel mills are often not adequate to generate high cooling rates and the cooling accuracy required for the production of AHSS. Hence there have been many developments for an intensive, highly flexible accurate homogeneous cooling technology. Considering the wide variety of strip and plate geometry, Primetals Technologies have developed Power Cooling Technology for strip and introduced MULPIC®4 Technology for the plate production. In this paper we shall discuss these enhanced technologies that provide the inline cooling requirement with examples from the recently commissioned machines.

Aug 17, 2017

By Shibu John

Rising energy demand and steadily decreasing quality of raw materials due to the global resource depletion are great challenges to the steel production today. The FINEX® Process has been developed jointly by POSCO, Korea and PRIMETALS Technologies Austria, to provide the iron making sector with the capability to lower hot metal production costs, environmental pollutions and to increase the flexibility in terms of operation and the choice of raw materials. FINEX® is a new technology combining a gas-based reduction in a series of fluidized bed reactors and a reduction smelting in a melter gasifier. Commenced in April 2007, the first 1.5Mtpa commercial plant has demonstrated the competiveness as an alternative iron making route. Another 2.0 Mtpa, third generation FINEX® (3G) plant was recently installed at POSCO, Pohang Works and has been operating satisfactorily since its blow-in in January 2014. Based on the well-proven plant concept, new process features, the highly competitive production costs and environmental advantages, the FINEX® Process can be considered as a competitive alternative to the conventional blast furnace iron making route.

Aug 17, 2017

By Márcia Maria da Silva Monteiro Pereira

Tundish is the last reactor where significant metallurgical operations can still be done. Calcium aluminate slags are able to positively contribute to metallurgy considering oxide separation, protection against reoxidation and preclusion of resulphurisation. However, these are poor insulators. When using low melting point slags it is necessary to use another covering material. The deviation from saturation can be used as a measure of absorption capacity. By utilizing computerized construction of ternary and quaternary diagrams it is possible to compare different slags and to find proper slag compositions with reasonable capacity to dissolve inclusions. Objective of the present technical contribution is to evaluate tundish slag capacity to absorb inclusions, considering a particular tundish industrial slag and the changes in its chemical composition during continuous casting of steel. It was observed that slag composition changed during the continuous casting process; this variation is possibly related to interaction between the CaO-Al2O3 liquid slag and the rice hull ash layer which is used above it. Computational thermodynamics was used to determine activity of alumina dissolved in liquid slag; it was observed that the variation in slag composition did not change slag capacity to absorb inclusions, since precipitation of Al2O3 solid phases is not predicted.

Aug 17, 2017

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Marcos Figueiredo Nicolau

O fluxo de produção da VSB contempla um alto-forno a carvão vegetal e uma aciaria elétrica. Para melhor sincronizar a programação do alto-forno (AF) e a do forno elétrico (FEA) é importante ter um conhecimento prévio de quais corridas do FEA usarão gusa líquido. Foi desenvolvido este projeto visando auxiliar na tomada de decisões da programação do AF e do FEA, a partir de uma simulação da logística de movimentação das panelas de gusa em cenários pré-determinados. Dentre as respostas que podem ser obtidas por essa contribuição técnica destacam-se: o número mínimo de panelas que devem ser utilizadas no circuito, quantas e quais corridas do forno elétrico serão atendidas com gusa líquido e a contribuição de cada meio de transferência de calor para a perda térmica total.

Aug 1, 2018

By Andreas Rohrhofer

Reliable high end automation and process optimization systems are main factors for excellent product quality, safe operation and maximized plant performance in the steel industry and its designated environmental plants. Primetals Technologies introduces new automation packages for consequent safe and cost efficient production. Many areas within the steelplant interested to be monitored and measured automatically are not implemented in the automation system due to limited access or technical reasons. A wireless, self-organizing network facilitates wide ranging data transmission in previously inaccessible areas and opens up a wide range of new opportunities. With Fluid Guard a system to detect leakages with highest accuracy and reacts properly for all kind of water cooled circuits is available, improving the safety in steelmaking process. Lance Guard can be utilized for all fully automatic and semi-automatic lance appliances, but is especially suitable for the products of Primetals Sublance Standard/2.0 and LiquiRob applications, since these systems make seamless integration particularly simple. Manual lance appliances may also be tested and diagnosed. Environmental plants have become a main part in steelmaking plants. Highest performance in combination with optimized energy consumption is the main target in Primetals Technologies’ innovations in automation optimization packages for dedusting systems. A new approach for preventive maintenance and operator assistance is introduced with the Acoustic Expert System. In combination with the new Ask cloud based system, Primetals enables a 24/7 monitoring and a whole lifetime observation of any equipment within a steelplant. Furthermore it is now enabled to check the condition of the plant at a fingertip at any time.

Aug 17, 2017

By Verônica Scarpini Candido

O estudo da composição mássica de cerâmicas vermelhas é de extrema importância para a produção de peças com propriedades tecnológicas aceitáveis. Nesse contexto esse trabalho tem por objetivo determinar as propriedades tecnológicas de cerâmica vermelha para fabricação de blocos de vedação. Dois tipos de argila foram usados, argila forte e fraca, para a confecção dos corpos de prova que foram moldados por prensagem uniaxial. Após essa etapa foram determinadas a absorção de água e a resistência em flexão. Os resultados mostraram que a massa composta por 50% de argila forte e 50% de argila fraca apresentaram os melhores resultados de resistência à flexão. Assim, o estudo mostrou que todas as massas estudadas atendem aos requisitos mínimos exigidos por norma e que a massa composta pela mistura das argilas apresentou o melhor desempenho mecânico tecnológico.

Oct 30, 2017

By Agnes Ágata Fróes Martins

O ensaio de impacto determina a resistência e sensibilidade dos materiais quando submetidos a uma certa carga de impacto, por isto, a importância deste ensaio. Através dele conhecemos as características que um material necessita ao ser projetado de tal maneira que possa suportar a uma força de impacto. Neste trabalho, o objetivo é comparar os resultados de energia absorvida no ensaio de Charpy analógico com o ensaio de Charpy instrumentado e verificar se há uma diferença significativa entre os resultados. Para isto, ensaios são realizados baseados em normas técnicas, neste caso a norma ASTM E23 [4]. Após os ensaios observou-se que os resultados do Charpy analógico e do Charpy instrumentado não obtiveram diferença significativa para todas as amostras ensaiadas. Em critério de avaliação dos resultados utilizamos a norma ASTM E2298 [8].

Aug 16, 2017

By Humberto Napoli BELLEI

O Sol é a principal fonte de energia sustentável com enorme potencial na geração de energia elétrica. O Brasil como outros países do mundo estão começando a construção de fazendas solares. Atualmente as especificações das estruturas para construção das estruturas dos painéis utilizados nessas fazendas tem sido de aços pós galvanizados justificado pela questão de tempo de garantia, principalmente, devido a presença de furos e bordas que ficariam protegidos contra a corrosão pela grande quantidade de revestimento utilizado. Nesse trabalho serão apresentados resultados de um aço pré-galvanizado que se mostrou seguro e confiável na proteção contra a corrosão dos furos e bordas dos painéis. O estudo teve como base as informações obtidas após o aço ter sido testado no ensaio em câmara de névoa salina e de dados já conhecidos em ensaios de campo.

Oct 30, 2017

By Alcio Heitor Somensari

O artigo apresenta um estudo de como um sistema de automação elétrica integrado deve fornecer uma completa visão do sistema elétrico, permitindo que as equipes de operação e manutenção tomem decisões precisas rapidamente após uma falha elétrica. As indústrias esperam que suas subestações estejam sempre disponíveis e ligadas, evitando paradas indesejadas. Para isso, precisam de soluções que recuperem o fornecimento de energia de forma rápida e segura, a um custo mínimo. Proporcionar um ambiente aprimorado na sala de controle para uma rápida solução de problemas e conectar subestações de locais hostis e distantes reduzem não apenas tempo de manutenção, mas também aumentam a segurança das equipes. A norma IEC 61850 nos permite entregar uma solução para um sistema mais intuitivo com acesso rápido a informações que melhoram a supervisão da planta na sala de controle.

Aug 16, 2017

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017