Search Documents

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By Mark Davis

As a follow-on to previous investigations, reduced treatment levels for the optimum fire retardant/preservative system were evaluated. An impregnation of 3.5 lbs/ft3 of Fyreprufe followed by 3.5 mils of Albi 107A plus an Albi 144 top coat provides adequate flammability and flame spread protection. However, there is a significant loss in compressive strength at this retention level, particularly parallel to the grain. A pilot-size pressure impregnation cell was installed for use in treating larger quantities of wood. Based on the optimum fire retardant/preservative treatment system - Fyreprufe/ACC impregnation followed by Albi 107A/144 intumescent paint - a model treatment pro¬cess was developed, capable of handling 3 million board feet per year. Associated annualized costs per thousand board feet (K bd. ft.) for treating 12" x 12" timber were calculated to be: Impregnation: $-63.00/K bd. ft. Coating: $112.00/K bd. ft. A literature search was conducted to identify materials and techniques suitable for a localized stench warning system for heated mine timbers. Based on this review, a number of stench warning concepts were developed. Those based on surface coating were given a preliminary laboratory evaluation.

Jan 1, 1982

By A. C. Fieldner

[The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according; to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-rank coals according to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.]

Jan 1, 1935

By W. L. Hunter

The preparation of coal for the commercial market is a study both varied and wide, and can be viewed from many angles and in different ways. This short paper can but touch upon the subject and is intended to discuss briefly preparation plants which in some cases would seem to be quite inadequate. The conditions confronting most operators are similar, inasmuch as the existing plants were not built specifically to prepare a product for the market of today, but rather of yesterday. The tremendous strides made in the field of combustion in recent years require that the product be of the highest grade procurable, and in a glutted and somewhat restricted market the buyer may be more pernickety than otherwise. These would appear to be the conditions of today. Where a mine is operated individually, better all-round results seem more readily procurable than in a consolidated effort where so many different conditions are sure to arise demanding cognizance, and in many cases requiring to be incorporated in the scheme of things. In the case of a number of mines being administered to form a central source, that source not having had anything to do with the bringing into being of the institutions over which it presides, we find some of the mines well equipped with facilities to properly screen and load the coal, while in others the facilities are not so good, but are doing their share towards delivering a product that will pass muster and in such quantities that they can be counted on.

Jan 1, 1930

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current wining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for drag line reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Tony Mazzo

It has often been said by consulting engineers that foundation contractors are in the business of taking risks. One would agree that the mere fact a foundation project can be budgeted, planned, engineered and executed solely on the reliability of eight test borings made at a proposed site having an area of approximately 19,000 square feet, is a risky proposition, in and of itself. Now imagine that this site is actually one half of a city block located in an urban setting in an old, congested, historical neighborhood, surrounded by narrow city streets and historic landmark buildings. And suppose that the required depth of excavation for the construction of the new building on this site is approximately 35 feet and the natural groundwater table is at a depth below existing grade of only 25 feet. Given the difficult site conditions outlined above, one could certainly add the words "challenging" and "complicated" to the inherent word "risky" when describing the construction techniques involved to undertake a foundation project of this magnitude. This case study will discuss in detail how the excavation, sheeting, dewatering and underpinning work was accomplished as well as the problems overcome along the way.

Jan 1, 2003

By Tom Dettweiler, Robina Sharpe, Wright. Michael

The International Seabed Authority and a number of countries have or are in the process of developing environmental impact assessment guidelines and legislation for seafloor mineral development. The formal decision to grant a project an environmental permit is based on an environmental and social impact assessment (ESIA), culminating in an environmental impact statement (EIS). The EIS needs to be supported by sufficient data upon which an assessment of impacts can be made and mitigation measures developed. Given the remote locations of many seafloor prospects, collection of sufficient environmental data to inform an EIS is often a difficult, expensive and lengthy process.

Sep 1, 2014

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

Sep 3, 2019