Search Documents

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly '1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By Per Eriksson

For light buildings on clay, foundations on L/C-columns is in many cases a competitive alternative to piles when the thickness of the clay is moderate (<20 m). The method is applicable for the above mentioned depth when the clay is normally consolidated, and for thicker deposits when the clay is overconsolidated at depth. This case study concerns a shopping mall in Nordby, Sweden, founded on L/C-columns (5-15 m in length) and generally spaced 1.45-2.0 m (spacing 0.7 m was used below pillars). The base slab was built as a raft foundation, using fibre reinforced concrete.

Jan 1, 2000

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

Mineral Processing Engineering Education in China - Bringing up the Engineering Diathesis and Design Competence of the College Students

Sep 13, 2010

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By Harry Sutcliffe

THE PROBLEM Two and a half years have gone by since the December, 1976 Civil Engineering article on subway costs caused such a furore. What has happened in this interval? Even after discounting the crushing inflation rate, costs are still increasing, and there is no sign of a turndown, even in the rate of increase. Some steps outlined in the article have been taken. In April this year, the first D.O.T.-sponsored Peer Review Group, made up of managers of other transit properties, met in Boston to review MBTA&apos;s $500 million Red Line Extension-Northwest for cost effectiveness. While the impact of a review at the end of the design phase, with substantial segments under contract, cannot be as effective as a review early in the design phase, it is nevertheless a start. This first meeting will be followed by a review of Boston&apos;s Orange Line relocation, the final design for which is just underway. In the industry at large two facts are evident: 1. We are failing to reduce underground construction costs. 2. Underground construction is in danger of pricing itself out of the market place. It has always been a greater challenge to design a Chevvy than to design a Cadillac, but it is the Chevvy we need today. Much attention has been focussed in the past on engineering design in the narrow sense: areas such as ground loading conditions and concrete design. This paper will attempt to make the case that costs in urban underground construction are primarily outside the area of structural

Jan 1, 1979

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By M. A. Leosson, S. H. Bottrell, R. J. Newton

Sylvite at Boulby is mined 1 140 m beneath the sea and the mine suffers from the influx of water. This is of two kinds: persistent flows originating in the Sherwood Sandstone aquifer and entering the evaporite sequence through fractures in the intervening mudstone, and impersistent flows which are transient in nature and of uncertain origin. Water from the overlying sandstone has become enriched with NaCl and large amounts of KCl and some Mg and Br have been added by interaction with the evaporites. Waters from the transient flows are isotopically distinct from those in the Sherwood Sandstone, being enriched in H and O. They are also saturated with respect to halite and sylvite, but have higher K/Na than the persistent flows and are much more enriched in Mg and Br

Jun 18, 1905

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth&apos;s crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

By John Jermain Porter

(San Francisco Meeting, October, 1911.) THE value of any particular ore, coke, or limestone, for iron-making, depends upon its effect, first, upon the quality or value of the resultant product; and second, upon the cost of smelting. The factors under the first head are the percentages of phosphorus, manganese, and other elements, which remain in the pig-iron ; while those under the second head are the percentages of iron, carbon, or lime, the slag-forming constituents, which must be fluxed, and any other ingredients which give rise to variations in cost of fuel and flux. The first of these criteria of value is perhaps not capable of being reduced to a general formula embracing all cases, since it must vary to a great extent with market-fluctuations. For example, Bessemer pig is worth sometimes more and sometimes less than foundry-pig ; and the premium paid for high manganese varies within wide limits. The second, or smelting-value, however, can be expressed numerically with a fair degree of accuracy; and it is with this phase of valuation that the present paper is concerned. The utility of a means of comparing numerically the relative smelting-values of different ores, cokes, and limestones, is self-evident, although it may not have importance in Northern practice, where materials are largely standardized. On the other hand, there are, especially in the South, many furnace-managers who must use a great variety of materials of widely varying grade; and it is with special reference to this district, and in connection with the efficiency-methods which I have elsewhere proposed,1 that the methods herein described were devised.

Mar 1, 1912

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004