Search Documents

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By M. W. Von Bernewitz

Fay's glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau's publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By G. B. Quaye

The deep level gold mining environment is characterized by high stresses that give rise to intense mining induced fracturing of the rock mass surrounding the stopes. In a geologically disturbed region where the intensity of mining induced stress fracturing is high, the degree of faulting and/or the frequency of other geological features such as joints may pose serious strata control problems. Unfavourable intersection of these discontinuities namely, faults, joints and mining induced stress fractures tend to divide the immediate hangingwall into unstable keyblocks which, if not supported, may result in extensive falls of ground. Effective support strategies therefore demand detailed investigation of the predominant inclinations and orientations of these discontinuities. The orientations and inclinations of these discontinuities surrounding a deep level stope have been measured. The results are projected onto the lower hemisphere of a stereographic net to determine the factors that contribute to the falls of ground in the stope. The analyses reveal that unfavourable intersection of these discontinuities divides the immediate hangingwall into unstable wedges that may become dislodged between support units.

Jan 1, 1998

By J. Koster

Boron is an element whose metallurgical possibilities never have been investigated thoroughly, probably because of the difficulties experienced in the preparation of elemental boron and its intermetallic compounds. The southwestern United States contain the world's largest deposits of boron minerals. In general, the mineral is readily available, and mining costs are not excessive. The most important boron mineral of commerce is borax (sodium tetraborate); however, there are large deposits of colemanite (a mineral having the composition represented by 2CaO 3B203 5H20) in Clark County, Nov. This material was worked in times past by converting it to sodium tetraborate. In recent years the deposits have laid idle because of a mere readily available source of borax in the old lake beds of California.

Jan 1, 1940

By Ronald T. Mayerle

A mineral survey of portions of two contiguous WSAs (Wilderness Study Areas) along the South Fork Owyhee River in southwestern Idaho and north-central Nevada was done by the U.S. Bureau of dines in 1984. The portions of the WSAs, known as study areas, have a combined area of 47,610 acres. The Idaho study area consists of 42,430 acres of the 42,510-acre South Fork Owyhee River WSA (ID-16-53). The Nevada study area consists of 5,180 acres of the 7,840-acre South Fork Owyhee River WSA (NV-010-103A). The Idaho study area is within the Boise District of the Bureau of Land Management, and the Nevada study area is within the Elko District. In the Nevada study area, no claims or hard rock mineral occurrences are known.

Jan 1, 1986

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By R. J. Gochin, G. D. Schena, R. Spencer

The impact of a mineral project in a developing country is evaluated in the broad context of its economy using input-output models. Minimum economic theory is used to develop simple numerical models. Sets of technical coefficients are exploited in the development of linear models of the productive element of an economy. The analysis allows assessment of the overall economic consequences of a mineral development in which issues broader in scope than financial objectives need to be incorporated in the evaluation. In part 1, the framework for the development of the input-output model is presented. The model is refined to incorporate country-specific behaviour. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy-wide effects associated with a new project in the mineral sector of a developing country. The relevance of the models is illustrated using an example from Namibia

Sep 1, 1991

By Maurice Deul

For the first half of the 21st century, the United States will rely on the same mix of fuels it has for the past 50 years. Petroleum for the United States will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in stress on the gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging “piggy-back” trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By J. Konnerup-Madsen, T. Unlu, H. Stendal

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The region includes the Deveci siderite/goethite deposit and the Hasancelebi, Karakuz and Kuluncak magnetite/goethite deposits; Deveci is the only mine in operation. The area consists of a serpentine-gabbro complex overlain by a volcano-sedimentary sequence hosting the iron ores. At least three generations of hydrothermal alteration have affected all rock types except the latest trachytic dykes. The Deveci deposits occur in a pyroclastic volcano-sedimentary sequence with shales and carbonates equivalent to the main mafic sequence, whereas the other three deposits formed contemporaneously with the intrusion of trachytic dykes. The deposits are of the volcanic-exhalative type, with syngenetic siderite in pillow lavas or stratiform layers the primary and main Fe-bearing mineral. In the west hydrothermal alteration has replaced siderite in pillow lavas with magnetite or has remobilised sideritic iron into magnetite veins

Apr 1, 1995

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate process plants requiring high throughputs presents unique metallurgical environmental and sustainability challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life-of-mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy and high ore variability, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, high capital and operating costs, worldwide constraints on resource availability, complicated regulations in emerging economies, changing demographics of mining operations with ever-changing cultural or community issues and the urgent need for a better assessment of project viability to reflect the dynamics of present mining scenario. Developing breakthrough solutions to these problems is the key to success of any new project and maintaining profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial along with the need for a more lateral thinking, strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex metallurgical problems.IntroductionThere is a plethora of challenges in developing new ore bodies. The metallurgical complexity of these deposits has increased significantly due to the need for mining lower grade ores along with the presence of deleterious elements that have environmental and processing implications. In addition, many of the mining projects are capital intensive due to high throughput requirements to be economical along with the need for building infrastructure due to remote locations, while operating costs steadily increase due to high reagent, energy and labour costs, increased state royalties and community obligations, to name a few of the key factors. There is also scarcity of water in many regions requiring the use of sea water or brackish water, which has both environmental and metallurgical implications. The shortage of qualified technical manpower adds significantly to the woes of many mining companies. Considering these multiplicity of challenges, it has become imperative for many mining companies to be innovative in addressing these issues."

Jan 1, 2015

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By Philip J. H. Ball

The new application and development of grout jacking processes has combined, over the last decade in particular, to provide a method by which the effects of new underground construction on superficial structures can be controlled to acceptable levels. This paper sets out the basic principles, processes and limitations of compensation grouting. It describes key elements of the philosophy and design and details the control systems required to perform satisfactorily. To illustrate the application, a case history is described for the construction of a shaft and tunnel within and beneath the prestigious structure of Harrods in London.

Jan 1, 2000

By P. J. Bartlett

Premier Diamond Mine exploits a kimberlite orebody using cave mining methods. A drilling level is established at the base of a block of ore to effect undercutting that leads to caving of the overlying ore. A second level is developed some 15 metres below the undercutting level to allow extraction of the ore once it has caved. As much as 45 per cent of the rock is removed on the extraction level creating a series of pillars. Undercutting creates abutment stresses, as high as 3 times the virgin stress, which affect the rock mass to a distance of 20 metres from the undercut face on the undercut level and on the extraction level 15 metres below. If the extraction level is completely developed prior to undercutting, where stress levels exceed 20 percent of the rock mass strength, extensive rock mass and support damage occurs as the undercut passes overhead. Rock mass damage takes the form of movement along existing joints and minor shear failure through intact rock. Support damage takes the form of cracking in rigid concrete linings. Where induced stresses exceed 50 per cent of the rock mass strength it is often impractical to keep excavations on the extraction level open. Rock mass damage takes the form of extensive failure of the rock in shear which evidences itself as propagation of the fracture zone around tunnels and footwall heave. Support damage results in destruction of shotcrete linings and concrete footwalls. As the interbolt support fails, badly fractured rock ravels around the steel tendons. Observation and monitoring at Premier Mine and on other cave mines has shown that induced stress levels and consequent damage are a function of :?the extraction ratio on the undercut and extraction level prior to undercutting ?the shape of the undercut face ?the rate of undercut advance ?the distance of leads and lags between adjacent tunnels on the undercut level. To ensure the stability of excavations, all of the above parameters must be carefully planned and the planned mining sequence rigidly enforced. The minimum of development is completed on the extraction level prior to the undercut passing overhead. Required development is then rapidly completed once the area has been de-stressed. Support is installed in three phases: ?Rockbolts are installed as soon as excavations are developed ?Wire mesh, steel tendon straps and a layer of shotcrete sufficient to protect the mesh and straps from damage by blasting and LHD loading is installed as soon as practical thereafter. Inevitably the shotcrete lining has to be replaced once the undercut has passed overhead.. ?Rigid shotcrete linings and concreted footwalls are completed only after the undercut has passed overhead and the area has been de-stressed.

Jan 1, 2000

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By R Lastra, J. A. Finch

An artificial standard material has been developed and used to examine the robustness of some of the procedures for correcting stereological bias. Different mineral liberation distributions were constructed from the standard material. The particles were mounted, sectioned and the sectioning data measured with an electron microscope interfaced to an image analyser. Four correction procedures were used and the corrected and true liberation distributions compared. It was found that the large-sections correction provided a simple, uncorrupted correction. Hill's fast approximation performed well except in cases of narrow liberation distributions; the sectioning data appeared to support the assumption that the locked section and locked particle distributions are identical. Barbery's correction performed well in most cases, having difficulty only with the very irregular liberation distribution. The PARGEN correction was able to provide a good estimate of the true amount of free material, but had difficulty in predicting the locked particle distribution

Jun 21, 1905