Search Documents

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By Paul H. Madsen, Victor S. Romero

The Tren Urbano project in Puerto Rico includes a 19 m diameter tunnel constructed by the stacked drift method, which involves installation of a pre-supported concrete arch using multiple tunnels. Geotechnical conditions consisted of weak rock and highly weathered, unstable alluvial soils. Due to low cover, reinforcement of the arch was required. Ground behavior ranged from firm ground to mixed-face to raveling and flowing ground. Consequently, construction of the individual drifts involved many different soft-ground techniques such as steel set supports, shotcrete support, shield tunneling, forepoling, and consolidation grouting. During construction, the design was modified to improve constructability. Although settlement was experienced during excavation of the drifts, arch movements were within predicted limits and minimal surface settlement was observed upon excavation of the interior.

Jan 1, 2001

By E. J. Gleim

A list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1942, was published in Bureau of Mines Information Circular 7207.3/ The list of that date was complete as to equipment then available and in current use. Information Circular 7240,4/ published as a supplement thereto, listed equipment approved curing the calendar year 1943. The present list is another supplement covering approvals issued during the calendar year 1943. The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gave 19 drills and drilling machines on the Bureau's active list. No additional approvals were given in 1942, but the three issued in 1943 bring the total to 22. Item 102, under Loading Machines and Conveyors, also appeared in Information Circular 7207, and items 120 and 124 appeared in Information Circular 7240. These numbers are repeated here to show that approvals were granted during 1943 for additional voltages on machines previously listed for one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept

Jan 1, 1944

By R. G. B. Pickering

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock?though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominately by means of scraper buckets and scraper winches?these were first introduced in the 1920s. Support is still mainly rock, either in situ pillars or backfill, or alternatively wood. Just as the mining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ?trackless mechanized mining? was introduced in the early1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to ?off the shelf? equipment. The move to introduce room-and-pillar mining into the narrow UG2 reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long hole drilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds?maximum reef recovery with minimum waste dilution.

Jan 1, 2002

By T Graham

The invention of the traditional belt and idler conveyor system is attributed to Thomas Robins in 1892. This basic concept, ubiquitous in most mining operations, has not changed markedly in 125 years and still suffers from five forms of energy losses. Firstly, Wheeler, Roberts and Jones (2004) showed that indentation rolling losses, a consequence of the indentation a roller inflicts on the belt, consume 60 per cent of all energy. Secondly, Wheeler (2006) explained that bulk solid flexure resistance resulting from material interaction and movement absorbs 20 per cent. The remaining energy is lost by idler rotating resistance (5 per cent), belt flexure resistance (5 per cent) and secondary resistances (10 per cent).Traditional conveyor systems are continuous as opposed to batch systems, implying both positive and negative features. On one hand, continuous systems have high availability (available infers ‘ready to run’), but, on the other, utilisation of availability is often low; for example, when a conveyor is running empty or below capacity. This converts into reduced system OEE (overall effective efficiency). Many attempts have been made to mitigate energy losses and low OEE issues, including development of rail-based systems. The key drawbacks have been higher capital cost, low flexibility, poor availability and lack of market acceptance.A recent conceptual development known as the ‘autonomous rail conveyor’ (ARC) promises to address issues of energy loss and poor availability and provide increased flexibility by offering solutions for difficult applications. The ARC uses a series of interconnected skeletal bogies covered with a conventional conveyor belt as a load bed running on relocatable light rail. The bogeys have two axles, each driven by integrated variable speed-geared motor and brake systems, and are connected to previous/next bogeys by specialised couplers. Power is provided by a generator (located in a dedicated bogey) and ‘daisy chain’ plug in cables. Centralised redundant control is provided at a preferred point. Although the system is batch in nature, the number of carriages and trains is flexible, meaning that the system is effectively continuous. Loading is achieved by feeding the ARC from a perpendicularly oriented apron feeder, while material off-loading is accomplished by a twist-dump operation in which the belt is twisted through an angle of 50° below the horizontal, causing material to flow from the belt into a receiving conveyor.The ARC system can run multiple trains over any distance, although benefits are more significant in distances of over two kilometres. Capital and operating costs are predicted to be lower than competitive products, with planned maintenance being simple to perform.CITATION:Graham, T, 2017. The autonomous rail conveyor significantly reduces ore haulage costs, in Proceedings Iron Ore 2017, pp 467–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P O. Koons, R J. Norris, S C. Cox

 The Southern Alps is an active oblique collisional zone which has a characteristic wedge-shaped geometry above a low-angle ductile shear zone. The Main Divide region is a relatively low strain zone above this ductile shear zone, and is _deforming principally along steeply dipping strike-slip faults. Extensional fractures are common at a high angle to the regional structural trend. These steeply dipping structures act as conduits for gold-bearing fluids from depth, and small mesothermal gold deposits have formed at several structural levels including the near-surface region. Gold has also been deposited in a meteoricmetamorphic fluid mixing zone near a conductive thermal anomaly on the western slopes of the mountains. These various gold deposits and their well-constrained structural and tectonic settings can be used as analogues for larger, deeper-eroded mesothermal gold deposits in the Mesozoic Otago Schist belt. High level Miocene veins in NW Otago have formed beneath the main divide of the initiating Southern Alps. Late metamorphic gold-bearing veins formed as fluid escaped from the ductile-deforming crustal root beneath Mesozoic mountains.  

Jan 1, 1997

By C. Stapel, AA Groningen, R. J. De Meijer

"In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

By N. D. L. Burger

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of steel wire rope slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist rope. This detaching is carried out via an additional detaching hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed to conform to established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted in most existing shafts. Given the simplicity and robustness of the designs, further development was recommended because of their enhanced self-sufficiency and reduced risk of malfunction. Keywords: underwind, overwind, deceleration, mineshafts, hoisting.

Jan 1, 2004

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By R. Patel, D. R. Taylor, P. M. Varley

In-situ measurements of ground stress were made from surface boreholes, using overcoring and hydrofracturing techniques, to obtain data for the detailed design of the underground works at Pergau. Unexpectedly low stresses were measured and appeared to correlate with apparent hydrofracturing observed during permeability testing. The low values of the minor principal stress had a major impact on design, particularly of the lining for the pressure tunnel and shaft. Additional hydrofracture tests were made underground during construction of the low- and high-pressure headrace tunnels and the pressure shaft, to define the vertical reduction in the minor principal stress with overburden. These data were then used to locate and design the steel and reinforced concrete linings

Jun 19, 1905

By A. J. Fejes

The purpose of this Bureau of Mines report is to provide mining industry personnel and regulatory authorities with a subsidence-reference list and annotated bibliography that will aid them in locating subsidence information and in developing their own subsidence information sources. Over 700 references are listed in the Bureau's subsidence information center bibliography; approximately 600 of these references were obtained for assessment. Of these 600 references, 167 were selected to be rated, categorized, and annotated. All literature referenced in this report was published prior to 1984. Table 1 is a cross - referenced index that classifies and rates selected references with respect to specific keywords. References are rated not on quality of content but rather on applicability to given subject areas. Appendix A is an annotated bibliography of the references listed in table 1 and provides further information of each article to aid the user in selecting articles for specific areas of subsidence technology. Appendix B is a copy of the subsidence information center bibliography.

Jan 1, 1985

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By P F. Lauricella, D Hendri

In the Mesel sediment-hosted disseminated gold deposit, the spatial distribution of hydrothermal alteration is controlled by steeply dipping faults and shallowly dipping lithologies. Hydrothermal alteration of carbonate rock is characterised by decalcification, dolomitisation and silicification. Intense argillic alteration occurs in a laccolithic andesite intrusion adjacent to decalcified and silicified carbonate units. Sulphide minerals (pyrite, realgar, orpiment, stibnite and cinnabar) accompany hydrothermal alteration and precious metal mineralisation. The trace elements Ag, As, Sb and Hg are zoned spatially throughout the deposit. Mesel contains a mineable gold reserve of 7.8 million tonnes at 7.3 g/t Au. Gold mineralisation is preferentially localised in carbonate rocks adjacent to and beneath the andesite intrusion. The ore body consists of a central, near-vertical, high grade 'feeder' system flanked by tabular, inward dipping, moderate grade 'ouflow' zones. Mineralisation is controlled predominantly by two steeply dipping faults with high grade (=10 g/t) gold zones centred about structural intersections and fault splays. Gold is submicron size and locked in very fine grained (<10 microns), disseminated and fracture-controlled arsenical pyrite. The Mesel deposit developed where high angle faults guided ascending, sulphidising fluids into reactive carbonate stratigraphy adjacent to and beneath the andesite intrusion and during subsequent migration of the auriferous fluids along 'outflow' channels. Early decalcification and dolomitisation enhanced porosity and permeability prior to silicification and sulphidation. Gold deposition occurred late in the genesis of the deposit.

Jan 1, 1995

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004