Search Documents

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001

The metallogenic map of New Zealand shows the distribution of metallic mineral deposits, according to type and size, in relation to their geological setting. The major purpose of the map and accompanying 200-page monograph is to summarise the distribution, modes of occurrence and origins of the metallic mineral deposits of New Zealand. The map demonstrates the prospectivity of New Zealand for metallic minerals, particularly gold, silver, iron, and titanium. Information on each deposit is summarised in index tables based on major geotectonic units or deposit/commodity type. The mineral deposits are arranged and discussed in relation to tectonostratigraphic and tectonomagmatic units or terranes, under broad geotectonic divisions of the Paleozoic to Mesozoic Western Province, the late Paleozoic to Mesozoic Eastern Province, the mid Cretaceous to early Tertiary rifting phase, and the late Cenozoic Kaikoura Orogen. Regions or areas of marked concentration of mineralisation are recognised as metallogenic subprovinces or districts, namely: eastern Northland (Hg), the Hauraki Goldfield (epithermal Au-Ag-Pb-Zn-Cu), the west coast of the North Island (shoreline placer Fe), east Nelson (podiform Cr), west Nelson (porphyry Mo), the West Coast of the South Island (shoreline placer Ti), west Nelson-Westland (placer Au), Reefton (mesothermal Au-quartz veins), and Otago (placer Au and mesothermal Au-W quartz veins).

Jan 1, 1993

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By Li Zhou

The kinetics of the dissolution of galena was studied by monitoring the mixed potential of a galena electrode in ferric sulfate solutions. The results show that the mixed potential of the galena electrode fluctuated with time in a regular pattern in a 0.1 mol/L Fe2(SO4)3 solution of pH 1.66 and in a 0.01 mol/L Fe2(SO4)3 solution of pH 2.33 at 35°C. The periodic accumulation and precipitation of lead ions at the galena electrode surface and the cyclical variation in pH at the galena electrode surface caused the oscillation phenomena.

Jan 1, 2008

By Pengfu Tan

A thermodynamic model has been developed to predict the distribution behaviors of Cu, Fe, S, O, Pb, Zn, As, and heat balance in a lead blast furnace. The modeling results have been validated by the plant data of a lead smelter in Asia. The model can be used to predict for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen-enriched air. The effects of the blast air, industrial oxygen, and coke charge on the distributions of Cu, Fe, S, O, Pb, Zn, As, and heat balance, and on the lead loss in slag have been presented and discussed.

Jan 1, 2005

By L. Mabiza

Keywords: Pyrometallurgy, circular furnace, PGM, platinum, Peirce-Smith converter, Zimbabwe The Zimplats Smelter, located on the northern part of the Great Dyke, at the Selous Metallurgical Complex, is the only PGM smelter in Zimbabwe. Zimplats? operations currently consist of the Ngezi Platinum Mine, which is a 1.5 Mt/a open-cast and 0.7 Mt/a underground mine, and a Concentrator and Smelter to which ore is transported 80 km by road. The final converter matte product is transported to Impala Refining Services in South Africa for refining and marketing. The Zimplats Smelter operations consist of a concentrate filtration plant, a Drytech flash dryer, a modified Elkem / Hatch 13.5 MVA circular furnace, two 10? x 15? Peirce-Smith converters, and a matte granulation plant. The Zimplats smelter uses a three-field electrostatic precipitator, supplied by ELB-Brandt, for removal of particulates in the gas streams from both the converter and furnace. Construction of the smelter commenced in 1995, under the BHP / Delta Gold of Australia joint venture. The furnace was lined mid-1996, and smelting operations commenced in 1997. Due to design challenges, the Elkem furnace was modified by Hatch in 1998, and the smelter had not reached full capacity when operations were suspended in 1999. Re-commissioning took place in January 2002.

Jan 1, 2006

The 109th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 16 August 2006. Special General Meeting A Special General Meeting to consider the changes to the Constitution was held immediately prior to the AGM. 1. Purpose In order for the SAIMM to remain relevant and ensure maximum value to all members, Council propose three changes to the Constitution. 2. Background Three changes to the Constitution were proposed by the Council on 21 July 2006. These changes now have to be approved by means of a ballot at a Special General Meeting. These three proposed changes are discussed briefly below:

Jan 1, 2006

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described. The methodology has been used to measure strain resulting from blasting, and establish appropriate blast vibration limits on a brick sewer tunnel, an underground mine heading, brick veneer houses, a water pipeline, and transmission tower foundations. An outline is given of the use of the methodology to establish limits for the main entry heading of an underground coal mine, and transmission tower footings. The methodology that is described has reduced uncertainty factors, and permitted the specification of higher blast vibration limits than had been previously used.

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By H. C. van Zyl

Mine water in the Upper Olifants River Catchment in Mpumalanga(upstream of Loskop Dam) is at times discharged into local streams, resulting in local acidification and regional salination of surface water resources. Pollution of surface water can be prevented by collecting and treating mine water to a quality where it could be re-used without restriction (Cleanwater 2020 Initiative). Mine water in the Olifants River Catchment currently amounts to only 4,6% of the total water usage, but contributes 78,4% of the sulphate load. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. A number of alternative desalination treatment technologies were investigated (subsequent to gypsum crystallization pre-treatment) where treated mine water must meet more stringent quality requirements (e.g. less than 200 mg/lSO4). The capital cost of these processes varied between R4 million/(Ml/d) and R10million/(Ml/d) and the running cost between R2/m3and R5/m3. Water usage in the Upper Olifants River Catchment currently amounts to 947 Ml/d (including the power stations), and will increase to an estimated 1385 Ml/d by 2020. The additional water demand by2020 (438 Ml/d) will have to be supplied by importation from neighbouring catchments, and more efficient utilization of the local water resources, including excess mine water. Various levels of treatment are required to make mine water suitable for the following potential applications (acceptable treated water sulphate concentration shown in brackets): irrigation (2000 mg/l), coal processing plant (1000 mg/l), general industrial use (500 mg/l), discharge to public streams (500 mg/l), potable use (200 mg/l) and cooling water in power stations (20 to 40 mg/l). The following two options, or a combination thereof, can be considered for management of excess mine water in the Upper Olifants River Catchment: ?Collection and treatment of excess mine water to a quality suitable for selected urban and industrial applications (Option A) ?Collection and treatment of mine water to a quality suitable for irrigation (Option B). The estimated capital and running cost for Option A amounts to R528.5 million and R55.7 million/year, respectively, compared with R68,2 million and R11,9 million/year for Option B. It is recommended that Option B be investigated for implementation in the short to medium-term. Option B was selected due to cost benefits and the initial favourable results obtained by a joint Water Research Commission and Coal Industry initiative where mine water is used for irrigation. Option A may become feasible in the long-term to ensure maximum environ-mental protection and reduced treatment cost as a result of anticipated technological improvements over the next 5 to 10 years.

Jan 1, 2001