Search Documents

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40°C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25°C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40°C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By K. Wongaew, R. F. Cook, J. E. Carlson, T. Cleys, C. R. Smith

Steel fiber reinforced concrete segmental rings are the final tunnel lining for approximately 85% of the alignment for a 6.706-meter (22-foot) internal diameter tunnel being built as part of the East Side Combined Sewer Overflow Tunnel Project. This paper describes the approach adopted for the design of the steel fiber reinforced concrete segments, the development of the performance criteria for the segments, and the testing program used to confirm the performance of the materials and segments in the laboratory and in the field.

Jan 1, 2007

By K Nilsson, D Connelly

Troy Resources acquired the Karouni Gold Project in Guyana, South America in 2014 and immediately proceeded to a Pre-Feasibility Study and project implementation. The study considered two open pit mines feeding a conventional carbon in leach (CIL) gold plant with a capacity of 1Mtpa. The study assumed a total of 2.61 million tonnes of ore with an average grade of 3.84 g/t gold with a recovered gold production of 303,526 ounces over a three year mine life.The project development involved drilling metallurgical test holes, securing second-hand major pieces of equipment where suitable, and arranging shipping to Guyana. The remote location meant logistical considerations were paramount. The plant consists of conventional two-stage crushing with single stage ball milling and a gravity circuit. The tailings circuit includes DETOX.The extremely high rainfall presented challenges with water management and the necessity to dispose of clean water to the environment. The DETOX was also mandatory due to the highly sensitive environment and past history in the area. The criticality of this meant that in the design, any cyanide in the tailings would precipitate in a plant shutdown.Lessons were learned and the project has been both profitable and successful for Troy Resources in a new operating location. In addition, the project has created jobs, delivered royalties and brought new skills into an area where previously there was little current mining activity.CITATION:Nilsson, K and Connelly, D, 2015. Karouni Gold Project from drill core to commissioning, in Proceedings MetPlant 2015, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By R. N. Tempel, M. Lengke

Arsenic sulfide [orpiment, realgar, amorphous AsS and As2S3] oxidation rates were measured in mixed flow reactors at pH~2 and temperature of 25-30oC. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2 s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH~2 from amorphous AsS > realgar > orpiment > amorphous As2S3. In comparison to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH~2.

Jan 1, 2002

Magnetic anomalies in the Southern Coalfields have been subdivided into two characteristic types. Each type is attributed to a separate cause, one being basement structure, and the other near-surface igneous intrusions.Detailed geological mapping of the area and the ability to sample throughout the coalmines greatly assisted in this subdivision.The Triassic sequence contributes no magnetic effect of its own except to diminish the effect of sources within the underlying formations by raising the level of observation.Detecting the presence of igneous intrusions ahead of colliery working faces by magnetic observations within the coal mines may be of value in preventing accidents caused by gas outbursts and in planning the workings so as to avoid loss of production time.

Jan 1, 1967

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

By Tianjiao Luo

Some literatures discussed on how to recycle the various reagent, but the discussion on how to reuse the waste liquid directly is very little. How to reuse the waste liquid directly was researched in this paper. Firstly, the waste liquid should be filtrated to remove the impurity; then some quantity of H2O2 solution was dripped into the waste liquid to pretreat it; finally, CuSO4solution was added into the treated waste liquid and the pH was adjusted to about 12, then some HCHO solution was added into the waste liquid, in which the treated carbon fiber can be plated. The morphology and composition of coatings were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), the deposition rate was mensurated by the way of dissolution. The results indicated that, the plating effect was basically identical with new plating solution, and the solution is stable, and the plating rate is still about 0.8µm/h, and the copper coating is even and combines closely with carbon fiber. According to this way, the waste liquid can be reuse 5~7 times.

Jan 1, 2006

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By K. P. Kavun, M. N. Denisov

Discussed in the paper is the redesigned reserve/resource classification for solid minerals being put forth by the authors to replace the acting Russian classification of 19961. The new version is based on the traditional foundations of former Russian classifications and the principles of the ‘McKelvey box’, both categorizing mineral resources according to the degree of geological assurance and economic viability. Based on these approaches the classification deliberately deals with both reserve and resource categories very similar to those established by the Geneva Accords in terms of definitions implied. The authors proceed from the UN-ECE proposed concept of ‘reserves’ being a part of ‘total resources’ explored in great detail by geological and feasibility studies and economically mineable at the time of reporting. The draft classification distinguishes ‘proved’, ‘probable’ and ‘possible’ categories of reserves depending on the stage of feasibility assessment carried out, i.e. the degree of detail and accuracy with which modifying factors affecting mineability of an orebody are taken into account. The reserves are regarded as a product of feasibility assessment of ‘measured’, ‘indicated’ and ‘inferred’ resources. The portions of them not having been classified as ‘reserves’ are regarded as composed of two classes: ‘subeconomic’ and ‘potentially economic’ resources (or ‘resource base’). All the cells of the classification matrix are provided with traditional for Russia alphanumeric designations and appropriate UNFC codes. The classification scheme recommended is viewed as a step forward in improvement of the State inventory and reporting mineral resources in market conditions, conducive to cross-border professional collaboration in the field of providing reliable information on the mineral rawmaterials base of the world’s economy. Besides, it recommends an easy way to get rid of amethodological error in the UNFC classification scheme where consecutive stages of geologicalexploration are identified with a single inherent degree of geological assurance. Keywords: mineral resources, mineral reserves, classification, geological assurance, feasibility studies, subeconomic resources, undiscovered resources, competent person.

Jan 1, 2003

By J. B. Czirr

MESA Corporation has completed a four-year program for the Bureau of Mines to develop a technique for measuring roof competence in underground coal mines. The preferred technique employs a tracer gas that is injected into a roof borehole drilled near the working face. The tracer gas performs the dual purpose of determining the pressure loss rate from the borehole and of marking the diffusion pattern of the the escaping gas. The primary detection technique relies upon observation of the rate of pressure drop in a hole drilled in the roof strata under test. If this measurement indicates a significant probability of roof collapse, the gas diffusion pattern is outlined with the Leak-gun tracer-gas detector. These two techniques provide a comprehensive method for predicting the relative probability of roof collapse in operating coal mines.

Jan 1, 1985

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."' The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-' have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.' Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.' The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13'17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,' using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By L. Yuan, A. C. Smith

To provide insights for the optimization of ventilation systems for U.S. underground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study was conducted to model the potential for spontaneous heating in longwall gob areas. A two longwall panel district using a bleeder ventilation system with a stationary longwall face was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the CFD modeling. In this study, the effect of methane emissions from the mined coal seam, including the longwall face and overlying rider seam reservoirs on the gob gas distribution was considered. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous-combustion studies. Unsteady state simulations were conducted, and the effects of the coal’s apparent activation energy and reaction surface area on the spontaneous heating process were also examined.1

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008

By W C. Cook, S J. Mathews, A H. Purvis

The Golden Cross Gold Mine is located at the head of the Waite kauri Ri ver, 8 km northwest of Waihi near the southern end of the Coromandel Range. The mine produces gold and silver from epithermal veins hosted by Miocene andesitic flows and pyroclastics of the Coromandel Group. Golden Cross is owned in joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Company Ltd (20 per cent). Mining is by open pit and underground methods. Mineralisation in a near-surface sheeted/stockworked vein zone is mined from the open pit. The deeper Empire Vein System is mined from underground where higher grade mineralisation is restricted to generally discrete veins. The open pit stockwork zone is west of and offset from the updip trend of the Empire Vein System. The Empire (hangingwall) Vein strikes generally north-northeast and dips steeply west. Dips become subvertical at greater depth. The hangingwall vein is a well developed, generally continuous structure with relatively high gold grades. A complex footwall vein system forms shallow west-dipping offshoots to the hangingwall vein. Structure and gold grades become increasingly erratic away from the hangingwall vein. The better developed footwall veins carry economic grades and high 'spot' grades over 50 g/t Au are not uncommon. Highest gold grades are associated with tightly crustiform banded sections of quartz veins and with dark fine grained siliceous breccias. The main hangingwall vein occupies a major north-northeast trending fault structure, the Empire Fault. Footwall veining forms within subordinate splinter fault zones. There has been extensive multidirectional pre-, syn- and post-mineralisation faulting. Fault manifestation is highly dependent on host rock characteristics. The central part of the hangingwall vein and surrounding silicified country rock has been shattered by a major fault structure, the West Mine Fault, forming a poorly consolidated, blocky quartz-breccia ore zone. Away from the more brittle ore zones and associated silicified envelope, wide clay-filled shears mark the major fault trends. Development of the deposit is considered to have occurred in two distinct stages related to separate episodes of dilational jog movement on the Empire Fault. The first phase reactivated the pre-existing Empire Fault as a dilational fissure with subordinate splinters on the footwall side. The Empire Vein System (hangingwall and associated footwall veining) formed during this phase. A second phase of renewed movement with further dilation resulted in more extensive fracturing of the Empire Vein and surrounding country rock and formed the sheeted/stockwork veining of the open pit. An upwards/westward migration of the hydrothermal system is assumed but fluid pathways between underground and open pit veining are unclear. Ore extraction and mining geology methods have responded to improved understanding of the grade and structural variability, and changing ground conditions inherent in the vein system. The underground mine produces ore from flatback cut and fill, post-pillar and bench stopes. Open pit and underground ores are campaign milled through a conventional CIP plant.

Jan 1, 1993

By John S. Hutchins, David L. Wassum

Mining engineers are ready to take a big step into a new field-oil mining. To understand the subject, one must look at the world's oil supply and demand as well as petroleum technology successes and failures. The US has an abundance of solid hydrocarbon and uranium energy resources, but 75% of its energy for industry, transportation, manufacturing, and space heating comes from liquid petroleum and natural gas. So there are increasing efforts to discover new oil reserves; today the number of drilling rigs operating in the US is at an all-time high. But with 80% of the world's wells already located in the US and Canada, good new exploration prospects are difficult to find. The cost of drilling deep new wells has also greatly increased. The US faced a similar situation in the early 1950s, when primary oil production declines began. During that time, the petroleum researcher introduced secondary recovery techniques such as water flooding and gas injection. This increased the average amount of extractable oil from discovered US reservoirs from 17% to 33%. Production soared and the world petroleum price remained stable until the end of the 1960s. Secondary recovery techniques were then supplemented by tertiary oil recovery technologies-increasing sweep efficiency with such things as CO2 injection-that are, so far, only partially successful in most petroleum fields. Even so, these technologies could raise cumulative recovery expectations to 35-38%. The "lost" oil in depleted US reservoirs equals 48 km3 (300 billion bbl) of conventional oil, or 12 times the current recoverable reserve base. At the present rate of US consumption-1 km3/a or 6 billion bbl/a-this is enough to run the US for 50 years without importing any oil. Moreover, there are 16-24 km3 (100-150 billion bbl) of as-yet unrecoverable heavy oil and tar sands in the US.

Jan 12, 1981

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

Research of 200 m3 Self-Suction Flotation Machine

Sep 13, 2010