Search Documents

By D. J. Benton, S. Finley, D. T. Orr, A. J. Chambers, M. A. Stepan

"Corrosion of ground support can lead to falls of ground that pose a significant risk to miner safety. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is investigating corrosion at the Hecla Mining Company’s Greens Creek Mine, located near Juneau, Alaska, USA. Field studies have used photogrammetry surveys to document welded-wire mesh corrosion, and laboratory studies at NIOSH’s Spokane Mining Research Division (SMRD) have investigated the effects of corrosion on ground support integrity. Findings show that (1) corrosion monitoring through photogrammetric methods may be effective for qualitative measurements of welded-wire mesh corrosion, and (2) there is a relationship between loss of load-bearing capacity and the diameter loss due to corrosion in welded-wire mesh. Photogrammetry results thus far have measured an apparent bulking of the corroded welded-wire mesh, and preliminary laboratory tests have investigated the relationship between the larger bulked and effective wire diameter. If this relationship is verified, these results may indicate that photogrammetry, when combined with the models produced in laboratory tests, could offer a means of monitoring corrosion levels, as well as rock rib deformation. INTRODUCTION Reducing the number of rock fall injuries and fatalities is an important part of the mission of the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD). Ground control using support systems to protect miners from rock falls is one of the oldest mining sciences, and considerable research has led to a variety of modern tools and methods in use today. Among these tools are rock bolts and welded-wire mesh, which are made from increasingly higher-strength steel grades to meet the increasingly demanding requirements of underground mines [1]. However, the benefits of these higher-quality support elements may be negated in corrosive mining environments. A better understanding of how corrosion affects the support capacity of ground support systems will assist engineers in determining when an opening is at a greater risk of falls of ground. Accelerated corrosion has been occurring in some areas of the Hecla Mining Company’s Greens Creek Mine near Juneau, Alaska, USA. Corrosion of ground support has resulted in two falls of ground occurring between April 2015 and March 2016. While these falls of ground did not injure any personnel, mine management recognized the high risk to miner safety and responded by actively undertaking a ground support rehabilitation program. Rehabilitation measures include the installation of both galvanized and coated, corrosion-resistant bolts and welded-wire mesh, depending on local conditions."

Jan 1, 2017

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By Harold L. Riley

This Bureau of Mines paper describes the methods and practices used at the Peck quarry of the Crab Orchard Stone Co., Inc., one of the leading producers of dimension stone in the Crossville, Tenn., area. The product is marketed under the registered trademark "Crab Orchard Stone". Another large producer of stone from the Crossville district sells its product under the registered trademark of "Tenn-Quartz". Both companies, and a number of other companies and individuals who quarry and process dimension stone from the same general geological formation, are members of the Quartzite Producers Association of Tennessee. The salable product is shipped throughout the country for use as architectural building stone. In 1959, 653,008 cubic feet of stone was produced in the Crossville area and was sold for $1,414,405. Terms and descriptions used in this report are those of the quarry and building trades. The offices, pitching sheds, wire saws, railroad siding, and storage areas of the Crab Orchard Stone Co., Inc., are on a side road 0.3 mile north from a point 2.2 miles east of Crossville, Tenn., on U.S. Highway 70. The quarry is on this same side road 2.0 miles south of Highway 70. Crossville is 62 miles west of Knoxville and 65 miles northeast of Chattanooga, Tenn.

Jan 1, 1962

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By Junfu Chen, Jiann-Yang Hwang, Yong Zhou, Lijun Lu, Likun Lia, Jixiong Liu

The sheet-like NiS-ZnS heterostructured composites were prepared by the microwave hydrothermal. The fabrication of the heterojunctions broadened the range of light response of ZnS. The photoexcited electrons of ZnS migrated to the redox potential of NiS/Ni2S under visible light irradiation, which can facilitate the effective separation of photogenerated electrons and holes in space. The visible photocatalytic activity towards hydrogen production for NiS/ZnS nanosheet heterostructed composites without co-catalyst achieved 0.28 mmol h–1, and the quantum efficiency was up to 18.6% under the wavelength with 420 nm visible light irradiation.

Jan 1, 2015

By Bruce H. Gardner

This paper describes the application procedure of the Stress Control mine design method. This procedure has evolved over the past 20 years of the practice of this Method in trona, potash, salt, and, most recently, in coal mining. The Stress Control Method of mine design has been defined and amply described in previously-published work (1,2,4) -- likewise, the associated system of in situ instrumentation (3,4) and the computer modelling technique (2,3,4) which are the principal tools of this method. The present paper defines the procedure by which the in situ instrumentation and computer modelling cools are combined in adapting the general concepts of Stress Control to produce site-specific design solutions. This procedure is illustrated by means of case examples from three mines. The Stress Control Method utilizes the geometry of underground excavations, particularly through the time sequence of the creation of yielding pillars, to control stresses. The time sequence is devised such that all the primary stress envelopes are transformed into a single secondary stress envelope, surrounding the group of rooms separated by the yielding pillars. The secondary stress envelope provides protection to the roof and floor boundaries from all the external stresses. This stress relief effect removes the cause of roof and floor failure -- high shear stress in the weakly confined boundaries of underground openings. It thereby replaces artificial support with ground self-support, enabling simultaneous in¬creases in stability and percent recovery. Within limits which are still being explored and extended, the Stress Control Method has proven capable of overcoming the trade-off between stability and extraction ratio which has afflicted conventional mining methods. The application procedure of the Stress Control Method is outlined below in terms of the objectives, structure, and stages of a generic mine rock mechanics program for the site-specific adaptation of the time control yield pillar design technique.

Jan 1, 1984

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By J Krawcz, S Wasilewski, W Mironowicz

Barometric pressure and its variation in deep underground workings have a considerable effect on ventilation conditions. Pressure changes which create transient states of air flow and air parameters in workings are especially significant. Experiments have shown that pressure changes have a remarkable effect on air parameters at mine workings and hence, attempts to evaluate the scale of this phenomenon are of value. Continuous monitoring of the barometric pressure on the surface of mines allows for the detection of changes in pressure which undoubtedly influence alternations of pressure in the underground areas of mines. Very important factors are the internal disturbances of pressure within a mine ventilation system due to variable conditions of fan operation and the operation of a winding machine where a mine cage moving in a shaft causes piston like disturbances. Local transient disturbances caused by temporary opening/closing of air stoppings due to personnel or underground transport traffic are of importance. The results of over two years of observations of barometric pressure and its influence on pressure variation in underground mine workings are presented in this paper. The observations were possible through the installation of pressure sensors at selected points of the downcast shaft in a mine. Of interest are the observations of the transient states of pressure and other air parameters caused by emergency fan stoppage, movement of a mine cage and changes due to the opening of air stoppings. Data acquired during experiments of opening and closing air stoppings were used for the validation of a flow model in a long working.

Jan 1, 2005

By A. J. Barry

Five makes of expansion-type shells and two types of bolts (mild-steel and high-strength) were used in 30 tests made in sandstone and shale roof, The results show that the anchorage obtained in both the sandstone and shale were stronger than either type of bolt. That is, the yield loads of both bolt types were exceeded before excessive anchor slip occurred. A relationship for evaluating the anchorage effectiveness of 3/8-inch-diameter, expansion-type bolts is presented. A comparison of test results indicates that the anchorage effectiveness of 5/8-inch- and 3/4-inch-diameter expansion-type bolts did not differ appreciably.

Jan 1, 1957

By C. C. Stevenson, Thomas Varley, E. P. Barrett, ROBERT H. BRADFORD

The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along metallurgical lines to warrant a definite statement as to the exact place it will occupy in the industry. The basic theory of the process has received the attention of prominent metallurgists for 20 years, and considerable research and experimental work have been carried on. Much of the experimental work done has never been published; if the accumulated results were made known, they would greatly aid,. the further development of the process. This bulletin aim~ to bring the salient features of the process to the attention of metallurgists for the purpose of furnishing information to and receiving comments from interested parties with the ultimate hope that the process will be a commercial success. If commercially utilized, the process will fill a long-felt want in metallurgy, especially in the treatment of oxidized and semioxidized or" carbonate" ores of copper, lead, and silver. Such ores are difficult to treat by gravity concentration or by flotation: in the former their tendency to slime upon crushing and their being of lower specific gravity than the sulphide minerals cause serious losses; in the latter much has been done in sulphidizing oxidized ores and subsequently recovering the artificial sulphides by flotation. Difficulties in proper sulphidizing and the low recoveries obtained have not balanced the cost of the treatment in many plants and in very few has it proved successful. Evidently there is a big void to fill in the treatment of these ores. No radical changes in present methods are forecast, but it is obvious that chloride volatilization can have a distinct place as a method of treatment for ores that are not readily amenable to present methods. In many plants it might replace concentration methods, especially where part of the mineral content in the ores exists in forms other than sulphides.

Jan 1, 1923

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By Alexandre Keunecke Hardt

A alta competitividade no setor siderúrgico aliada ao dinamismo crescente do mercado internacional tem forçado as empresas a estarem mais preparadas para eventuais necessidades de mudanças em seus processos e produtos. Em muitas situações, o tempo de resposta de uma empresa para adaptar-se a uma nova necessidade, estratégia ou tecnologia determina o sucesso ou fracasso da iniciativa. As soluções MOM, como responsáveis pelo gerenciamento da produção, possuem um papel fundamental no intuito de facilitar a adaptação da empresa a uma nova realidade. Nesse contexto, a adaptabilidade e a flexibilidade das ferramentas MOM tornam-se fatores extremamente relevantes no momento de definição de um produto ou concepção de uma solução. Este trabalho tem como objetivo refletir sobre o papel das soluções MOM como acelerador de mudanças dentro das indústrias. Serão apresentadas as características principais de um sistema MOM preparado para o cenário dinâmico atual, bem como alguns critérios para avaliação da adaptabilidade e flexibilidade de uma solução MOM.

Jul 30, 2018

By Paavo Eerola

In May of 1984, it was decided that Outokumpu Oy would design and build a new nickel flotation mill to process ore from the newly discovered Enonkoski mine in eastern Finland. Since there hart peen a number of successful process charges in the existing mills, the design effort included the study and incorporation of several new developments, including all-autogenous grinding, "flash flotation", lane cell roughing, large cell cleaning and a computer-based, profit optimizing, process control system. The paper discusses the background and results of those studies, and a description of the resulting mill which will begin production in 1986.

Jan 1, 1985

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By W. W. Adams, T. D. Lawrence

"Despite the manpower shortage and other difficulties of operation in war time, the National Safety Competition of 1943 for the promotion of safety in the mineral industries of the United States was notable for having a larger enrollment of mines and quarries than in any other year except 1941 and 1942 since the yearly safety contests were inaugurated in 1925. The competition was also notable for having a larger number of man-hours represented by the competing companies than in any previous contest except that of 1942. The ratio of accidents and days of disability resulting from accidents to the number of man-hours of work performed was more favorable than in 1942; the accident-frequency rate was lower and therefore better than in 13 of the 19 years during which the annual safety competitions have been conducted, and the accident-severity rate was better than in 16 of the 19 years.The National Safety Competition is a yearly safety contest conducted by the Bureau of Mines, United States Department of the Interior. Companies that win first place in their respective group in the contest are awarded a bronze trophy, ""The Sentinels of Safety,"" which is provided by THE EXPLOSIVES ENGINEER magazine. Competing companies are segregated into six groups: Underground bituminous-coal mines, underground anthracite mines (in Pennsylvania), underground metal mines, underground nonmetallic-mineral mines, open-cut mines (without regard to kind of mineral produced), and open quarries (without regard to kind of stone produced). The bronze trophies are retained by the six winning companies for 1 year and are then transferred to the winners of the succeeding year's contest. On the pedestal of each trophy is engraved the names of the winners of the trophy. With the award of the trophies for 1943, therefore, the pedestal of each trophy bears the names of 19 winners."

Aug 1, 1944

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By C. E. Baltzer

This paper highlights the position of coal supply in regard to the requirements for electric-utility operations. The text and the appended tables outline the trend of thermal power development and fuel use in the electric-utility industry. Mention is made of several argumentative factors influencing the use of coal in relation to competitive oil and gas, and of the importance attached to developing a realistic understanding of the respective problems faced by the supplier and consumer of coal. * * * TREND OF" THERMAL POWER DEVELOPMENT T HE RATE OF ADVANCE in thermal power has been significant during recent years, particularly in the Atlantic Provinces, the Prairie Provinces, Ontario, and British Columbia. While dependence on thermal power in Quebec and the Northern Territories is less than in the remainder of Canada, these regions also eventually will have need for increased amounts of such power.

Jan 1, 1961

By E. Dendy Sloan

An overview of hydrate properties is given, with emphasis on unusual deviations from ice, the most common solid water form. Reliable sample preparation and reproduction of in situ hydrates provide the foundation for all hydrate science and engineering. Relations are given to connect the three domains in the title: (1) micro-scopic properties measured with Raman, NMR, and diffraction spectroscopy, (2) meso-scopic properties measured with single crystals, and (3) macro-scopic properties measured with pressures, temperatures, volumes, etc. A principal illustration relates micro-scopic and macro-scopic domains. Experiments provides the basis for improving statistical thermodynamics model for these compounds. To date, this model is one of the most commonly used industrial statistical thermodynamics applications, based upon the classical model of van der Waals and Platteeuw (1959). Microscopic measurements and simulations indicate model assumption improvements, resulting in the next generation of the statistical thermodynamics for improved macroscopic property prediction.

Jan 1, 2002