Search Documents

By G. E. Pearse

Reports, discussions, a written contribution and two written replies are presented from 11 sessions on: Safety and compressed air; Ground movements; Geotechnical; Channel Tunnel (2 sessions); Machines; Case histories; Transport tunnels; Case studies; Site investigation; and Undersea tunnels

Jun 13, 1905

By Thomas A. Earl

Strip mining of coal, and to a lesser extent limestone, gravel and other mineral deposits in the Appalachian region of the eastern United States has left many large and small areas of devastated land where mining predated reclamation requirements. In Pennsylvania alone, there are between 250,000 and 370,000 acres of strip-mined land 1,2/. A higher percentage, and a greater total acreage of land in Pennsylvania is in need of some form of reclamation than any other state, with the neighboring states of Ohio and Nest Virginia also having nearly the same magnitude of mining.2/ Recent legislation governing strip mining of coal proposed royalties to cover reclamation of such presently unusable land. However, in Pennsylvania and other states some progress has already been realized by utilizing abandoned strip mines and gravel pits for waste disposal sites. Given acceptable hydrogeologic settings, such use of these mined areas for landfilling has provided the incentive for ultimately restoring unreclaimed land to beneficial use, at no cost to the general public.

Jan 1, 1975

By Márcio Nascimento Cunha

Titânio é adicionado aos aços inoxidáveis ferríticos para melhorar a resistência à corrosão e estabilizar a estrutura ferrítica. Devido à afinidade com oxigênio no aço líquido, perdas de titânio por oxidação são comuns, sendo as adições realizadas após etapas de desoxidação. Inclusões de titânio podem causar obstruções na válvula submersa durante o Lingotamento e também defeitos superficiais no produto final. Técnicas para obter inclusões menos prejudiciais às propriedades dos aços têm sido empregadas e a obtenção de inclusões com ponto de fusão mais baixo após tratamento com cálcio tem se mostrado efetivo. Os objetivos deste trabalho foram avaliar a composição química das inclusões no aço inoxidável 409 após adições de titânio no Forno Panela e o efeito da adição de cálcio no comportamento das inclusões. Amostras do aço líquido foram retiradas no Forno Panela em corridas com e sem adição de Ca-Si. A composição química das inclusões foi analisada no MEV-EDS.

Aug 17, 2017

By J. R. CAMERON

Gypsum is mined in all Atlantic Provinces except Prince Edward Island. It is generally thought to have been derived from the hydration of anhydrite in areas of minimal drainage. Late Devonian downwarping and crustal oscillation east of the Appalachian fold belt allowed the Windsor Sea to advance and retreat in a depositional trough and deposit about 1,000 m of sediments in Mississippian time, much of which were evaporites. The best areas for further gypsum development are lowland basins such as the Cape Breton Lowlands, the Hillsborough area of New Brunswick and the St. George's Lowlands in Newfoundland, all of which are already sites of gypsum quarries. Nova Scotia's gypsum is mined from the Lower Windsor Group, which is divided into subzones 'A' and 'B'; 'B' provides most of the province's gypsum production. The Atlantic Provinces gypsum industry has markets from the St. Lawrence waterway to the mouth of the Mississippi River.

Jan 1, 1984

By B. H. Clemmons

A field method has been devised for rapid determination of heavy minerals occurring in the unconsolidatod beach and dune sands. The method has been proved practical by usage in field evaluations of several hundred beach- and dune-sand samples in the Florida area. The simple equipment required and the techniques involved are described. Other data show that the method is relatively insensitive to variations in the mineralogical content or size distribution of the mixed heavy minerals contained in the samples tested. A modification of this procedure, found to be suitable for plant use in determining the relative purity of heavy-mineral flotation concentrates, is also described. A specific application is determination of the amount of feldspar-quartz in spodumene flotation concentrates. The results of the rapid evaluation techniques closely approximate those obtained by more precise laboratory procedures.

Jan 1, 1957

By A. E. Wheeler, H. Y. Eagle

The copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minére du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1934

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By Flávia Guimarães Rocha Godinho Campos Vargas

Amostragem pode ser definida como a sequência de operações que visam retirar do todo (lote) uma parcela (amostra) que conserve as propriedades de interesse do lote. O menor erro possível em um protocolo de amostragem é chamado de erro fundamental de amostragem (FSE), o qual está associado à heterogeneidade constitucional do minério e pode ser estimado através de testes de heterogeneidade. A realização do teste de heterogeneidade com minério fonte de zinco, proveniente da mina de Vazante, permitiu concluir que a heterogeneidade da willemita é menor que a heterogeneidade de minérios de ouro e maior que a de minérios fonte de alumínio, por exemplo. Além disso, os resultados do teste de heterogeneidade permitiram a otimização do protocolo de preparação de amostras do laboratório físico, reduzindo o erro total de 13,4% para 6,0% sem investimentos em infraestrutura de laboratório.

Aug 17, 2017

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

By Pedro Gabriel Bonella de Oliveira

O processo usual para elaboração de aços utilizados na indústria de petróleo e gás é a laminação controlada, porém, não é adequado para fabricação de peças de geometria complexa, como juntas e conexões. Nestes casos, o forjamento é a melhor opção, pois permite maior diversidade de conformação. A produção de componentes por esta técnica exige tratamentos de têmpera e revenimento para obtenção das propriedades exigidas em trabalho. O objetivo deste projeto é avaliar o comportamento em tração e a microestrutura de um aço microligado submetido ao aquecimento a 855, 900 e 1000°C. Modelos termodinâmicos de Kasatkin foram utilizados para cálculo das temperaturas de transformação austenítica. Os resultados mostram que o tratamento realizado na zona de transformação intercrítica favorece a formação de uma estrutura bifásica de ferrita e martensita com maiores valores da tensão de escoamento e resistência máxima à tração. Nos tratamentos térmicos realizados em maiores temperaturas há diminuição na resistência mecânica, porém com aumento no alongamento em consequência de uma estrutura composta de bainita e ferrita acicular.

Aug 17, 2017

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By Robert L. Vines

"What is past is prologue" - motto of National Archives The question of past, present, and future safety performance in the coal mining industry is not merely an academic one, or one which arises from soul-searching curiosity. It is a question involving pragmatic ramifications, and the answers, or perhaps the public perception of the answers, will have a strong impact on the public policies which influence the course of meeting the Nation's future energy demands. Those of us in the coal industry are keenly aware of the significant impact of the public reaction -- in the form of the 1969 Health and Safety Act -- to -past performance of the coal industry which it found unacceptable. That Act was revolutionary -- and it was expensive. But in finding the industry's past performance unacceptable, the public also recognized its own contributory role through having enjoyed a "buyer's market" forced on a highly competitive industry. One result was to limit the industry's resources and restrict its ability for self-improvement of its safety performance. In acknowledgement of that role, the public picked up the tab for Black Lung disability incurred prior to that time.

Jan 1, 1985

By Aly Mohammad, Dongyi Yue

"The design of rock sockets for drilled shafts and piles proves to be a challenge for the Design Engineer. The magnitude of loads on the shaft and the behavior of the rock are critical in determining the required socket length. Several acceptable methods are available in the literature to analyze a rock socket under a combination of axial loads, lateral loads and moments. This paper will present a state-of-the-art methodology to analyze rock sockets utilizing deformation characteristics of the rock. This design methodology was implemented in the design of a major project in New York City.The project discussed herein is a marine transfer station planned for construction at East 91st Street along the East River in Manhattan. In order to support the piers and platform structures at a site with relatively shallow depth of the bedrock, rock sockets were required for the drilled shaft foundations. Rock sockets were utilized to provide the required fixity to the foundations and the structures. Acting at the top of the rock sockets are large shear forces and moments created by the lateral loads transferred from the structure.Upon review of the available techniques, a simplified method was proposed and used to analyze the rock sockets with a significant magnitude of lateral loading. The method recognizes two mechanisms through which the lateral shear and moment are transferred to the rock; a) load transfer through horizontal resistance of rock and b) the vertical shear resistance of the bond between socket and rock.The first load transfer mechanism was analyzed using the p-y curve method based on a rock model developed by Reese. The second was analyzed using a bond stiffness derived from the formula and curves utilized in the AASHTO Specifications for calculation of rock socket displacement. By comparing the two mechanisms, the main contribution to the large horizontal shear force that developed in the rock socket is identified.The paper will present a summary of the design methodology utilized in determining the length of the rock socket. It is believed that the presented method will provide substantial cost saving in selecting the most economical and efficient design length."

Jan 1, 2005

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Huijun Shao, Qiang Liu, Zhengming Yi

The increase of the proportion of high Al2O3 content iron ore fine in iron and steel enterprises has brought about a series of problems such as the increase of the viscosity of blast furnace slag and the difficulty of the separation of slag and iron. In order to solve this problem, the effect of increasing MgO content on the technical and economic index, the cold strength, and metallurgical properties of high basicity and high-alumina sinter was studied through sinter pot test. Nova400NanoSEM field emission scanning electron microscope was used to analyze sinter microstructure. The experimental results show that when the MgO content fraction in the sinter with high basicity and high aluminum increases from 1.72 to 2.49%, the vertical sintering speed decreases by 4.38mm/min, the utilization coefficient decreases by 0.51t/(m2 h), and the low-temperature reduction degradation index increases by 6.7%. When MgO content in sinter is 2.11%, drum index and reducibility index are the highest, reaching 61.93% and 86.39% respectively. Mg2+ is mainly solid dissolved in the magnetite lattice and replaces Fe2+, up to 3.64%. The generated magnesie-containing magnetite inhibits the phase transition from Fe3O4 to Fe2O3 oxidation process in the sinter cooling process, which reduces the generation of secondary hematite and is conducive to improving the low-temperature reduction degradation performance of sinter.

Jul 4, 2021

By Walisson Silva Gomes

A injeção de carvão pulverizado pelas ventaneiras dos altos-fornos é um dos meios de redução de custos de produção do ferro gusa. Esta injeção deve ser de forma efetiva para evitar possíveis desperdícios de combustível. Esse trabalho teve como objetivo desenvolver uma metodologia de quantificação do teor de carbono na lama e no pó de coletor, gerados na limpeza de gás do alto-forno para auxiliar a avaliação da eficiência de queima do carvão injetado pelas ventaneiras e sua correlação com as variáveis de processo. Nenhuma norma especifica a quantificação de carbono na lama e no pó de coletor. Foram utilizadas duas técnicas de quantificação de carbono em carvão e coque utilizados na Companhia Siderúrgica Nacional, a Análise Imediata, baseadas na norma ASTM D 5142-09, e a Análise Elementar. Um estudo mais detalhado para investigar as possíveis interferências nesses métodos de análise, devido a diferença de resultados entre eles, foi utilizado Difração de Raio-X, associado ao método de Rietveld, e Analise Termogravimétrica de Calorimetria Exploratória Diferencial (TG-DSC). A partir dessas análises foi possível definir o melhor método para quantificação de carbono no pó de coletor e lama de alto-forno.

Aug 17, 2017

By Gabrielle Luana Jimenez

Aparelhos eletroeletrônicos como computadores e televisões são constituídos por telas de cristal líquido, que ao se tornarem obsoletos são classificados como resíduos, e dispostos em aterros sanitários. Entretanto, na composição das telas de cristal líquido há metais de valor agregado, como o índio (In). Com a fundamentação no processo de reciclagem de telas de LCD, este estudo propõe a recuperação e quantificação desse metal que é encontrado na forma de ITO (óxido de índio e estanho). Para tal feito, foram empregadas rotas hidrometalúrgicas, tendo como principal etapa a lixiviação. Como parâmetros de controle, os ensaios de extração sólido-líquido foram realizados em temperaturas que variam de 50 a 80°C. Com isso, foi obtido resultado de extração do índio em cerca de 60% em massa, nas condições de 60°C e após 4 horas de lixiviação.

Aug 17, 2017

By José Eustáquio da Silva

Este trabalho mostra a versatilidade e praticidade do uso da metodologia denominada “Método e Aparelho para Avaliar as Propriedades de Coqueificação do Carvão”, metodologia esta desenvolvida e patenteada pelo corpo técnico da SunCoke Energy. Esta técnica tem possibilitado o desenvolvimento de novas misturas de carvões totalmente alinhadas com os dois grandes pilares da Siderurgia mundial: misturas e coque com baixo custo e qualidade adequada. A fidelização com todas as particularidades do processo real de coqueificação faz desta metodologia uma poderosa ferramenta para tomada de decisão na definição de novos blends, como também para a caracterização de carvões dos quais ainda não se conhece seu potencial para produzir um coque de boa qualidade. Diferentemente das tecnologias similares existentes, o “Box Test” da SunCoke Energy tem robustez suficiente para ser reutilizado para até quatro enfornamentos e é capaz de produzir massa suficiente de coque para que sejam realizadas todas as análises para uma perfeita caracterização do coque.

Aug 17, 2017