Search Documents

By J. K. Weglo, M. U. Savich

"The measurement and evaluation of the noise emanating from an ST4A scooptram in an underground stope under a simulated work cycle, and under three conditions of after-treatment systems is covered.These include scooptram without muffler or filler (bare engine), an in-line small filter, compared to a larger-filter, and the larger filter with an in-line muffler in series with fume diluter, which were tested under three engine operating conditions-IDLE, wide open throttle (W. 0. T.), and working condition. This is load, short haul and dump operation.The results showed an attenuation of the scooptram at work of 8 to 15 dBA, 16 cm from the exhaust pipe of the machine, to 4.8 dBA at the operator's ear. Recommendations are made to increase the attenuation at the operator 's ear by additional improvement in design of the fume diluter.IntroductionIn current mining operations, the diesel engine provides a safe, efficient and highly mobile source of power. In the major underground mine s in Canada the most common types of diesel equipment are load-haul-dump (LHD) machines and ore trucks. In general, there is a tendency to use high horsepower, diesel LHD machines in mines to achieve maximum productivity. The increased use of diesel-powered equipment in underground mines has shown no cause pressure levels were measured at the exhaust and outlet pipe. Also, while measuring the octave band and A-weighted sound pressure levels, the operator's position was also measured."

Jan 1, 1986

By Jerry E. Olson

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied additional areas, encompassing 11,303 acres, on the east and west sides of the 20,727-acre Badlands study area (Olson, 1987) in order to evaluate their identified mineral resources. The Badlands study area additions are located in Crook and Deschutes Counties, OR, about 10 and 18 miles east of Bend, OR. No mineral resources were identified. The additional areas studied are underlain by Tertiary-and Quaternary-age basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, mining claims or mineralized areas occur within or near the Badlands study area additions. Slab lava of marketable grade and quantity was not found in either area. None of the study area is of current interest for geothermal resources, but the eastern study area addition has been leased (1984) for oil and gas.

Jan 1, 1989

By Yi Luo, Jian Yang

Subsurface strata movements and deformations associated with longwall mining operations in underground coal mines could cause various disturbances to subsurface mine structures, ground water bodies, and coalbed methane reservoirs. In order to assess those disturbances correctly and to design effective and efficient mitigation measures, it is necessary to develop an accurate prediction model for subsurface strata movements and deformations. Decades of research have demonstrated that variations of stratification and lithology in the overburden have significant influence on the subsurface strata movements and deformations during ground subsidence process. The key strata theory states that the thick and hard key strata serve as the backbone of the overburden and control the movements of the thin and soft weak strata located above them. From an engineering standpoint, the overburden strata are subdivided into several individual groups by the key strata with each group consisting of a key layer at the bottom and weak layers overlying it. A new subsurface subsidence prediction model considering the key strata effects on subsurface strata movements and deformations has been proposed. In this method, elastic modulus, specific weight, tensile strength, and uniaxial compressive strength (UCS) of each layer are used to identify the key layers and to determine the needed subsurface subsidence parameters. The influence function method, proven to be accurate and versatile for surface subsidence prediction, was employed to predict the subsidence on each of the overburden layers from mining horizon progressively upward to ground surface with the assumption that the predicted subsidence on a given layer serves as the subsidence source for the layer immediately above. The enhanced subsurface subsidence prediction model has been demonstrated with an actual case to show its applicability and improvement.

Jan 25, 2021

By Guy Bridges

Site formation works requiring excavation of rock at the Queen Mary Hospital redevelopment site was restricted due to extremely low ground vibration limits. Non-Explosive excavation method called Electro Power Impactor (EPI), sometimes called Plasma Blasting, was utilised to help ensure the rock excavation rate could meet the required programme.

Feb 1, 2020

By George A. Laird

I. INTRODUCTION. THIS old and once famous district played, through its enormous production of silver and gold, an important part in the history of the State of San Luis Potosi. According to a pamphlet prepared under the direction of the Governor of the State, Sr. Don Blas Escontria, and presented to the visiting members of the Institute during the Mexican meeting of 1901, this district is situated 20 km. east of the city of San Luis Potosi, in a range of mountains of moderate height, extending 135 km. N. and S., and 16 km. E. and W.; and the mineralized area hitherto developed is about 600,000 sq. m. The history of the district,. as given by the record dated 1778, and formerly kept in the San Francisco convent, says that it was discovered in 1575 by Sr. Don Pedro Irarte, and adds that the city of San Luis Rey de Francisco del Potosi received its name (in allusion to the famous Potosi mines in Bolivia) by reason of the remarkable productiveness of its gold- and silver-mines in the first period of their exploration, during which they paid to the Crown, as " quintos " (the fifth part of the product), $97,000,000, as appears from the accounts of the royal treasury. The amount of the quientos paid during the " bonanza period " of 80 years was $72,000,000. The larger sum first mentioned probably represents a longer series of years. But either will suffice to indicate the great wealth of the mines. In 1663, the decadence of the industry began with the caving¬ in of several mines, concerning which the record of 1778, al¬ready cited, says, in substance, that on Good Friday one of the owners in the enterprise, in view of the unfavorable prospect of a lawsuit in which he was engaged, set fire to the timbers supporting the underground galleries and workings of the San

Jan 1, 1905

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990

By P. E. Lenz

In Nevada, large deposits of diatomite were formed during the Miocene / Pliocene in deep, alkaline lakes. Associated sediments are predominately fine-grained lacustrine with varying fluvial-clastic layers. Tephra layers are common, and probably served as a source of soluble silica for the extensive diatom colonies. Four companies are currently producing diatomite from Nevada deposits. Nevada ranks second to California in annual domestic production. Nevada diatomite is used in filter aids, fillers, absorbents, catalyst supports, and many other products. Economics and mineral reserves indicate that diatomite production in Nevada will be significant well into the next century.

Jan 1, 1993

By Stephen P. Holt, John A. Bowsher

A preliminary examination of the mica deposits in Culberson and Hudspeth Counties , Texas , was made in September 1942 by A. B. Needham, district engineer of the Bureau of Mines . The deposits were reexamined by R. C. Redfield , associate mining engineer of the Bureau in November 1942, at which time he was accompanied by Philip S. Hoyt , geologist , and J. C. Moore , foreman of the Texas Mica and Feldspar Company . Exploratory work was started on February 16 , 1944 , and terminated on April 30 , 1944. A crew of 4 to 10 men was employed under the supervision of the authors .

Feb 1, 1947

By Ann Hubbs, Vincent Castranova, Jane Y. C. Ma, De-Hwa Chao, Joseph K. H. Ma

AN OVERVIEW OF THE ACTION OF TETRANDRINE ON SILICOSISBecause of the persistent presence of silica dust in the lungs silicosis is a progressive and irreversible disease. At present, there is no proven effective therapy for silicosis. Limited choices of therapeutic intervention with corticosteroids and other immunosuppressive regimens 1,2 have been accepted for some forms of pulmonary fibrosis. These treatments are only minimally effective, and the results provide little understanding of the disease state due to the lack of correlation between drug activity and the mechanism of fibrosis. Thus, continuing effort must be made in the search for effective antifibrotic agents, which may be used to provide a sequential analysis of the fibrotic process and to open the door for further research and clinical development. Tetrandrine is one of hundreds of drugs screened for antifibrotic activity by Chinese scientists. It has been used in China as a treatment for silicosis in open clinical trials3 and in laboratory animals. The action of tetrandrine on pulmonary fibrosis has been attributed to its ability to inhibit particle stimulation of alveolar macrophages, a key cell type central to the fibrotic process, to release oxygen radicals and inflammatory cytokines. Alveolar macrophages (AM) residing on the alveolar wall, are the predominant phagocytic cells of the lungs responsible for pulmonary defense against inhaled microorganisms and other particles and thus play an important role in maintaining the homeostasis of the lungs. 7 Ample evidence suggests that cells of the monocyte-macrophage series play an important role in the immunopathogenesis of pulmonary fibrosis. When upregulated by silica, alveolar macrophages generate reactive oxygen metabolites8·9 which can damage lung parenchyma and release fibrogenic growth factors and cytokines, 10,11 such as interleukin 1 (IL-1), which can induce fibroblast proliferation and collagen synthesis. The cytokine-mediated fibroblast proliferation and collagen synthesis are key steps in the development and progression of pulmonary fibrosis .11 Previous studies by our group have shown that tetrandrine exhibits strong binding affinity to AM and inhibits particle-stimulated respiratory burst activity (oxygen consumption, superoxide anion release, and hydrogen peroxide secretion) in these cells. 13 In addition, studies by Kang et al. 14 have reported that tetrandrine inhibits silica-induced release of fibrogenic factors such as IL-1 which are capable of inducing fibroblast proliferation and collagen synthesis. Reist et al. 15 further suggested that the antifibrotic action of tetrandrine may be mediated in part by the direct effect of this drug on the ability of fibroblasts to respond to proliferative agents. These results indicate that the mechanism of silicosis involves activation of AM and fibroblasts by silica, resulting in abnormal collagen production due to miscommunications between the cell types. Tetrandrine may interrupt this process by direct interaction with the lung cells.

Jan 1, 1998

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By Josée Dartois

En 1988, à l?instar de plusieurs états du monde industrialisé, le Québec décidait d?accélérer la cadence de l?assainissement des rejets industriels et lançait un programme intégré de réduction de la pollution industrielle visant, à la fois, les rejets dans le milieu aquatique, les émissions atmosphériques et les matières résiduelles. Ce programme fut intitulé le Programme de réduction des rejets industriels.

Nov 1, 2002

By Edward Jacobsen

The Oak Creek Power Plant in Oak Creek, Wisconsin is currently undertaking an expansion project. In order to supply cooling water to this facility, a 27' (8.2m) diameter tunnel will be bored, in rock; to connect to 4 vertical Intake shafts located approximately 1.5 miles (2.4km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to Install these intake shafts. When complete, the plant is expected to circulate upward of 2 billion gallons per day (7.5 billion liters) through this system. Two shafts were drilled in a (shortened) construction season in 2005 and the remaining 2 shafts and 4 liner assemblies were completed in 2006. Future connection to the tunnel, in 2007, will be accomplished by mining upward to reach the lower portion of each liner and then removing its internal bulkheads to permit the flow of the lake water into the tunnel.

May 11, 2007

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By E. D. Regad, W. E. Wallace, P. S. Mike, C. A. Hill, V. Vallyathan, M. J. Keane

"Respirable-sized quartz, a well-established fibrogenic mineral dust, is compared with kaolin in erythrocyte hemolysis assays aher treatment with saline dispersion of dipalmitoyl phosphatidylcholine, a primary phospholipid component of pulmonary surfactant. Both dusts are rendered inactive after treatment, but the membranolytic activity is partly to fully restored aher treatment with phospholipase Ai. an enzyme normally associated with cellular plasma membranes and lysosomes. Phospholipid-coated dusts were incubated for periods of 2-72 h at a series of applied enzyme concentrations, and the adsorbed lipid species and hemolytic activity were quantitated at each time for both dusts. Surfactant was lost more readily from quartz than from kaolin, with consequent more rapid restoration of mineral surface hemolytic activity for quartz. Interactions of surfactant and mineral surface functional groups responsible for the mineral-specific rate differences, and implications for determining the mineral surface bioavailability of silica and silicate dusts, are discussed. INTRODUCTIONMineral particles depositing in the lung acinus will contact an aqueous coating containing surfactant molecules spread on the air-liquid interface and dispersed within this hypophase; the primary components of that surfactant are diacyl lecithin phospholipids (King and Clements, 1972; King, 1982). Adsorption of this surfactant can suppress the cytotoxicity of mineral dusts (Marks, 1957). Suppression of hemolytic activity, a measure of membranolytic potential and an indicator of bioavailability of the mineral surface, of respirable-sized quartz and kaolin clay dusts with the adsorption of dipalmitoyl glycerophosphorylcholine or dipalmitoyl lecithin (DPL) has been measured (Wallace et al., 1985). Such contact and adsorption of pulmonary surfactant in vivo may provide a first defense system of the lung against respired dusts."

Mar 1, 1992

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By J. P. Remi Proulx, Areli Rodriguez, Ruilin Yang

Historically, presplitting has been considered effective in reducing the impact of blast vibrations on highwalls. However, it remains a debated topic: how significantly can it protect highwalls, and is it worth the cost and effort to implement presplit blasting techniques? In hard rock, presplit blasting can leave half-barrels on the highwalls, clearly demonstrating its usefulness. However, in a fractured rock mass, the half-barrels from presplit blasting may not appear in most cases, leading to questions about its role in protecting highwalls. Previous studies in the literature used geophones to measure blast vibrations at far distances and could not ascertain the significant benefit of presplit blasting in reducing the impact of blast vibrations on highwalls. Additionally, no studies in the literature address the role of presplitting in alleviating blasting-released gas pressure that could penetrate joints and open new fractures in highwalls. Yang & Proulx (2019) and Yang et al. (2022) using near-field blast vibration monitoring of signature hole blasts have revealed that the peak particle velocity (PPV) of blast vibrations at a scaled distance of 1 m/kg^0.5 can be reduced by 50% or more for presplit-filtered vibrations. These results have been confirmed for both hard rock and fractured ground. In addition to summarizing the reduction in blast vibrations due to presplitting for both hard rock and a fractured rock mass, this paper demonstrates the relief of subsequent blasting gases after the detonation of blastholes. This is shown through video recordings of gas ejections from a row of empty previously fired presplit blastholes located 6 to 9 meters away from the detonation edge or final buffer row of a blasthole pattern. The results clearly show that presplitting not only lowers blast vibration PPV’s but also reduces the entry of the gases produced by the detonation process into rock fractures and or open joints.

Jan 21, 2025

By Shun-ichi Satoh

The electric arc welding of cast iron has been studied by Braune Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer Candy, Neese, Miller, Carter, American Welding Society, Namack Lebrun, Achenbach, Jansson, Xochendorffer and others.' The write of this paper has been able to obtain a series of cast irons, from gray tc white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (Sic) and graphite (C). In this work, he found the curious phenomenon of barium carbonate.

Jan 1, 1929