Search Documents

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world's largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the cost approach category for real property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties. The author reasons that standards and regulations pertaining to real property valuation should be modified, and underlying principles should be expanded, so as not to inhibit appropriate application of these cost approach methods.

Jan 1, 2011

By O. Norman Lotter

The formulation and use of mixed collector suites in sulphide flotation can be traced back as far as 1957 with the work of Glembottskii and his co-workers in Moscow. The subject was reviewed by Lotter and Bradshaw in 2010, and proposed a synergy between ideally-selected different reagent types to deliver improved performance, in particular the in situ catalysis of a xanthate to dixanthogen by a dithiocarbamate. Correctly formulated for a particular application, an optimally arranged mixed collector suite delivers the following improvements to the flotation process: • An increase in the flotation kinetics • Improvement in coarse, or middling, particle recovery • Reduction in total dosage requirement • Best results are found from testing the ratios of the collectors. This is of critical importance. In all an optimally formulated mixed collector system usually delivers an increase in paymetals recovery of 1–4% absolute, with a gain in concentrate grade in the range 10–20% relative. In recent years, the addition of semi-conductor theory and associated electrochemistry has contributed significantly to this toolbox by way of identifying optimum domains of Eh and pH for the flotation of individual minerals. In the case of mixtures of minerals, this is where the mixed collector system delivers significant value by way of presenting a mixed set of collector radicals and dimers in a common Eh and pH domain for overall performance. This calls on a fundamental understanding of organic chemistry, mineralogy, semiconductor theory, and electrochemistry. Whereas the selection of grinding media type effectively influences the Eh, the pH can be easily controlled by pH modifiers. The theory of this system, and some industrial case studies, are discussed.

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

By Luis Velásquez

El shotcrete reforzado con fibras de acero es un conjunto discreto discontinuo de fibras de acero contenidas en el concreto, los cuales son proyectados neumáticamente a altas velocidades sobre una superficie. En este sentido, el presente texto describe la importancia de dicha materia prima -en tanto otorga resistencia a la rotura y es un esfuerzo estructural del shotcrete en las operaciones mineras. Al tiempo que reduce el empleo y tiempo de la mano de obra, así como contribuye la seguridad del personal minero.

Sep 14, 2009

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $23,629,500 for the 1; 06- million-ton-per-year (MM tpy) mine to $79,907,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $35,336,500 to $1 18,863,500 for the same mines. Corresponding selling prices for the coal range from $13.57 to $11.36 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1975

By Pierre Sauvé, Alex Makila

"The Camflo stock of porphyritic quartz syenite is an irregular pipe-like body 200 metres in diameter injected along the axial plane of an E-W trending F2 fold, near the contact between the. Kewagama and Malartic groups. The stock plunges 55° to the NE, almost parallel to the fold axis. The stock, exhibiting pervasive, weak cataclasis with numerous, locally auriferous quartz veinlets, is cut by minor faults striking WNW and dipping about 45°NE.Two types of gold ore are distinguished at Camflo: ""porphyry"" ore and ""fault zone"" ore. ""Porphyry"" ore, accounting for 90% of the gold produced, forms wide zones within the stock. The zones are irregular in shape but tend to be oriented E-W in plan view (on a horizontal plane) and are elongated paraliel to the plunge of the stock. These zones are more abundant in the northern part of the stock. Differences between ore and barren porphyry are not obvious. ""Fault zone"" ore occurs outside the stock along minor faults, particularly in differentiated sills offer rodiorite and felsic granophyre. Gold grade is roughly proportional to the pyrite content which in turns depends in part on the original magnetite content of the host rock. Although both types of ore show some correlation between Au and S, the Au/S ratio is considerably higher in porphyry ore.The bulk of the gold is in quartz syenite and in felsic granophyre, the most brittle lithologies at the mine. Presumably, the vertically continuous, pipe-like stock, made up of shattered rock, provided the main channelway for the ascending mineralizing solutions."

Jan 1, 1990

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By Jim Sundal

Primary steel manufacturers using electric arc furnaces generate one of the largest hazardous waste streams nationwide. The waste stream, known as electric arc furnace dust, is a listed hazardous waste with the designation K061. Oregon Steel Mills, Inc., (OSM) of Portland, Oregon, has implemented a process known as Glassificationn, which uses KO61 as an ingredient in an onsite recycling process. Because OSM was able to demonstrate that the Glassificationm recycling process beneficially uses all toxic constituents in the electric arc furnace dust and that the recycling process produces marketable products, the process is not subject to Resource Conservation and Recovery Act (RCRA) permit requirements. The marketable products manufactured using Glassificationn include roofing granules, ceramic glazes and colorants, abrasive blasting media and, more recently, synthetic slag fluidizers. The purpose of this paper is to identify the regulatory issues for recycling hazardous waste and demonstrate that OSM glass frit is effective as a slag fluidizer in primary steel manufacturing.

Jan 1, 1994

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By Enrique Pasquel Carbajal

El presente texto describe los resultados realizados por el Centro de Investigación tecnológica del Cemento y del Concreto (CIDETEC) sobre el empleo de microalfiler de carbonato de calcio como adición mineral para mejorar las propiedades reológicas en estado fresco y endurecido del shockrete empleado en las labores de sostenimiento en la industria minera. Asimismo, se señalan la aplicación de esta tecnologías en proyectos mineros como Cobriza, Andaychagua, San Cristobal y Pallancata.

Sep 12, 2011

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (>1 per cent dry basis) and sodium (>0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

By Glen C. Reed

"The Avon mica district of Latah County, Idaho, is situated on a heavily forested spur of the Thatuna Range at an average altitude of 4,000 feet. The nearest rail connection is at Avon, a small farming settlement 7 miles to the south. The main supply point is Moscow, Idaho, which is 35 miles by graveled and graded county roads from Avon.Discovery of mica-bearing pegmatites in 1885 was followed in 1888 by exploitation of several outcrop deposits. Although factual data are unavailable, past production appears to have been well in excess of $100,000. Recent production (September 191 to April 1945) amounted to 65,824.78 pounds of trimmed sheet mica and 33,294.17 pounds of punch mica having a total gross value of $434,298.The several properties of the district are variously owned by estates, individuals, and the State. When active, all wore under lease or sublease to individual operators.The deposits are in an area of pre-Cambrian schists adjacent to a small granitic outlier of the Idaho batholith. The pegmatites are nearly concordant in dip and strike to the foliation of the enclosing schists. The more persistent bodies are usually tabular, lenticular, or pegmatite. Individual dikes range in length from 10 feet or less to 300 feet.The recoverable crude mica content of the pegmatites ranges downward from a maximum of 115 pounds per ton of pegmatite mined. Material discarded in rifting and trimming operations further reduces recovery to a maximum of 5 pounds per ton -of pegmatite mined. The average recoverable sheet content of the 'recently operated .deposit is estimated at 2 pounds per ton of pegmatite -mined. Available data indicate that about 21 percent of the district's recent production of trimmed sheet mica has been ""Group A"" material suitable for exacting condenser requirements. A few of the dikes contain local concentrations of beryl.Reserves of the three known major deposits of the district are estimated at about 600 to 1,000 tons of combined ""indicated"" and ""inferred"" crude block mica. One of these deposits is inferred to contain between 150 and 450 tons of beryl.It is believed that those mica reserves are minable only under a cost-market price ratio similar to that established during 1943 and 1944. A small part of the reserves can be ""high-graded"" under the present price structure. Profitable recovery of the beryl would require a market price four to five times that paid in 1944.Preliminary examination of the Avon mica district was made by the Bureau of Mines in the summer and fall of 1942. A study of the Muscovite mine and a brief reconnaissance of the surrounding district led the Bureau to recommend that the district be explored by angle-dozer trenching."

Jul 1, 1946

By Doug Russell

Natsource: At a Glance l 160 employees l Global reach ? New York, Washington, Calgary, Ottawa, Toronto, London, Tokyo l Major Environmental Commodity Broker ? Rated as Top GHG Broker (Environmental Finance Magazine Survey, Dec. 2000 & 2001) ? Leading RECs Broker ? Large Broker of SO2, NOx l Large Energy Broker ? One of Highest Volume Gas Brokers ? Major Electricity Broker Overview l International Market l Implementing the Rate-Based Proposal l Assessment and Management of Risk from GHG Emissions Limitations

Nov 1, 2002

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By R. J. Stevens

The Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft ('934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (I) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory furnaces in terms of tons of copper produced per ton of coal burned is high. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table I shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is suficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 22 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1949