Search Documents

By Anjana C. P, K. Ranga Swamy

The hilly regions of Kerala are severely affected by excess rainfall, causing tremendous damage due to landslides and slope failures. It is necessary to strengthen the existing slope profiles to prevent such disasters and avoid their risk to human lives and civil infrastructures. This paper studies the effect of micro pile to reinforce the slopes in Idukki district of Kerala, where slope failures are frequent. Three-dimensional slope stability analysis is carried out on slopes from the Idukki to obtain safety factor values using the MIDAS GTS NX program. The slope is fully saturated herein by taking the model's piezometric surface at the ground level to simulate high rainfall intensity. The critical slopes are then modelled with micro piles to analyze their effectiveness in improving the stability under static conditions. Different micro pile arrangements are considered, and a series of slope stability analyses have been carried out to obtain the optimum configuration with the required safety factor. The FOS values increased by more than 50% with micro piles for all the slopes. The optimum micro pile arrangement obtained for each slope shows that micro pile distribution between the toe and middle of the slope is an effective location for reinforcing slopes.

Sep 1, 2022

By B. J. Nelson, F. N. Rhinos

Studies upon the rates of oxidation of copper alloys containing small quantities of the alloying elementsl,2 have shown that steady growth of the scales at predictable rates is limited to a small concentration range and to oxidation at temperatures above 600°C., whereas unpredictable and erratic oxidation behavior is found with alloys containing larger additions and at low temperatures. The latter effect appears to be associated with modifications in the geometric disposition of the oxides. At low concentrations of the baser elements in copper, simple oxidation behavior is typified by the formation of two distinguishable zones of oxidation: (I) a subscale composed of discrete particles of the oxide of the alloying element embedded in substantially pure copper and (2) an external scale composed of cuprous oxide (with a very thin layer of cupric oxide on the outside) containing particles of the alloying element distributed throughout, but most profusely near the metal surface (see Fig. 2, top). Where this type of structure obtains, the process of oxidation is believed to be implemented, and its rate controlled, by the diffusion of the reacting elements through a' continuous matrix phase; i.e., through the alpha (metallic) phase of the subscale and alloy and through the cuprous oxide of the external scale. Copper is presumed to diffuse outward through the cuprous oxide layer to the external surface, where it reacts to form more cuprous oxide.3 Oxygen is delivered at the oxide-metal interface in the form of cuprous oxide, which may either react with the alloying element to deposit its oxide at the inner limit of the external scale or dissolve in the pure copper that remains at the surface of the metal after it has become depleted in its oxidiza-ble alloying elements. Both oxygen and the alloying element are pictured as diffusing through the metal, the oxygen inward and the alloying element outward. Where the two diffusion streams meet in sufficient concentration the oxide of the subscale is precipitated. If the oxygen pressure in the surrounding atmosphere is just below the pressure necessary to maintain cuprous oxide undecomposed, no cuprous oxide can be formed; some of the oxide of the alloying element may form upon the external surface, if its decomposition pressure is below that of cuprous oxide, and a normal sub-scale appears. This condition is achieved experimentally by enclosing the alloy with cuprous oxide together with an excess of copper. At temperatures from 600°C. downward, the precipitated oxides tend to accumulate at the grain boundaries of the alpha phase where a relatively small volume establishes a partial barrier to the diffusion of the reactants- Similarly, large volumes of Precipitated oxides tend to deposit in various patterns that may be expected to

Jan 1, 1944

By F. N. Rhinos, B. J. Nelson

Studies upon the rates of oxidation of copper alloys containing small quantities of the alloying elementsl,2 have shown that steady growth of the scales at predictable rates is limited to a small concentration range and to oxidation at temperatures above 600°C., whereas unpredictable and erratic oxidation behavior is found with alloys containing larger additions and at low temperatures. The latter effect appears to be associated with modifications in the geometric disposition of the oxides. At low concentrations of the baser elements in copper, simple oxidation behavior is typified by the formation of two distinguishable zones of oxidation: (I) a subscale composed of discrete particles of the oxide of the alloying element embedded in substantially pure copper and (2) an external scale composed of cuprous oxide (with a very thin layer of cupric oxide on the outside) containing particles of the alloying element distributed throughout, but most profusely near the metal surface (see Fig. 2, top). Where this type of structure obtains, the process of oxidation is believed to be implemented, and its rate controlled, by the diffusion of the reacting elements through a' continuous matrix phase; i.e., through the alpha (metallic) phase of the subscale and alloy and through the cuprous oxide of the external scale. Copper is presumed to diffuse outward through the cuprous oxide layer to the external surface, where it reacts to form more cuprous oxide.3 Oxygen is delivered at the oxide-metal interface in the form of cuprous oxide, which may either react with the alloying element to deposit its oxide at the inner limit of the external scale or dissolve in the pure copper that remains at the surface of the metal after it has become depleted in its oxidiza-ble alloying elements. Both oxygen and the alloying element are pictured as diffusing through the metal, the oxygen inward and the alloying element outward. Where the two diffusion streams meet in sufficient concentration the oxide of the subscale is precipitated. If the oxygen pressure in the surrounding atmosphere is just below the pressure necessary to maintain cuprous oxide undecomposed, no cuprous oxide can be formed; some of the oxide of the alloying element may form upon the external surface, if its decomposition pressure is below that of cuprous oxide, and a normal sub-scale appears. This condition is achieved experimentally by enclosing the alloy with cuprous oxide together with an excess of copper. At temperatures from 600°C. downward, the precipitated oxides tend to accumulate at the grain boundaries of the alpha phase where a relatively small volume establishes a partial barrier to the diffusion of the reactants- Similarly, large volumes of Precipitated oxides tend to deposit in various patterns that may be expected to

Jan 1, 1944

By Samuel Canchaya M.

El presente trabajo señala los diferentes métodos geoestadísticos utilizados en la industría minera. Por ello, las aplicaciones de la geoestadística abarcan todas las fases de un proyecto minero que va desde la prospección hasta el tratamiento metalúrgico. Asimismo, los métodos geoestadísticos por su rigidez matemática, objetividad y eficiencia varias veces demostrada, pueden desplazar a los métodos tradicionales, cuyos errores e inexactitudes fueron poco advertidos en el pasado, debido a la bonanza y relativa accesibilidad de los depósitos minerales.

May 1, 1984

By James Corcoran, Richard McLane, Matt Neuner, Joseph DeMello, Hugh Davies

The Los Angeles County Metropolitan Transportation Authority (LA Metro) Purple Line Extension Section 1 (PLE1) is a $3.12 billion USD design-build, underground heavy rail project, connecting an existing station at Wilshire Blvd. and Western Ave. and extending 3.92 miles under Wilshire Blvd, terminating approximately 550 feet west of Wilshire and La Cienega Blvds. The project alignment runs immediately adjacent to the La Brea Tar Pits, world renowned for Pleistocene fossils and continuous seepage of asphaltum (locally known as tar) and gas in an urban setting. This paper presents a successful case history of the planning, design, and construction efforts to safely construct the bored tunnels through Reach 3 of the alignment (between Wilshire/Fairfax Station, and Wilshire/La Cienega Station), in a designated Methane Zone in the City of Los Angeles. Historical context on decades of challenges and studies is summarized. Further, this paper outlines the pro-active partnership between the Owner: LA Metro, the Design Builder: Skanska-Traylor-Shea Joint Venture, and geotechnical design services provided by Golder Associates to safely manage pressurized face tunneling through a confined gas zone near the La Brea Tar Pits. Specifically, a program of in-situ oxidation and soil gas extraction was designed to test and analyze risks associated with pressurized face TBM tunneling through the complex subsurface geological conditions, then implemented during construction. In advance of tunneling, a network of wells was used to draw air into the gas zone to oxidize the 6,500 ppm hydrogen sulfide gas, as well as determine methane recharge rate. During TBM tunneling, the wells were converted to a gas extraction system to evacuate, filter (H2S) and burn (CH4) the gas as the Tunnel Boring Machine passed, providing a preferential pathway for the gas to migrate toward extraction wells, and preventing the migration to adjacent buildings. The team extracted and treated 3,857,000 cubic feet of mostly methane gas over 40 days as the TBMs passed through the zone. Gas behavior, pressures, and concentrations were monitored not only from the extraction system, but also in basements and utility vaults along this section of the alignment.

Jun 13, 2023

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By Shigetoyo Yasui, Masahiro Saitou, Nobushige Yasuoka, Keisuke Tsujimoto

"The Dry Jet Mixing (DJM) Method was developed and has been put to practical use on the initiative of the Public Works Research Institute and Japan Construction Method and Machinery Research Institute. This method is used to inject powdery binder with compressed air into soft ground while mixing the binder with the soil using the mixing blade to reduce the moisture content of the ground and cause chemical reactions between the soil and binder, thereby strengthening the ground and stabilizing its quality.Recently, there is a demand for high-quality, high-accuracy execution control.This paper introduces the New DJM Execution Control System, developed to meet the future demand for more sophisticated ground improvement, based on the past results of the conventional system in order to provide new automated execution control with improved accuracy, functionality and column quantity.1. INTRODUCTIONIn association with the densification of cities and the improvement of the social overhead capital, the underground space in urban areas is tangled with various underground structures including transportation facilities such as subways and underground roads, buried pipe such as water supply and sewerage systems,gas, electric power and communications lines, and underground malls.In addition, a lot of aboveground structures such as office and residential buildings, elevated tracks, expressways, embankment tracks are also supported with underground foundations.Tokyo, Osaka, Nagoya and many other large cities in Japan grow on plains spread along the coast or rivers. Waterfront flat areas which are very convenient for human activities, however, are often on the alluvial soft ground, where soft cohesive soil with a high moisture content, loose sandy soil, etc. are accumulated in a thick formation, with a high groundwater level.The DJM Method introduced here is used to decrease the moisture content of the soft ground, strengthen the ground and stabilize the soil quality by injecting powdery binder into the ground with compressed air, while mixing the binder with the soil using the mixing blade.2. OUTLINE OF DJM METHODThe DJM Method is used to inject powdery binder with compressed air into soft ground, while mixing the binder with the soil using the mixing blade, to cause chemical reactions between the soil and binder, thereby decreasing the moisture content of the ground and strengthen and stabilize the ground."

Jan 1, 2015

There were two official representatives of Foreign Governments as guests at the Chicago Meeting. One was Frederick Goransson, managing director of the Saudvikens Steel Works, who represented the Jernkonteret, the Iron and Steel In-stitute of Sweden, and who came to this country especially for our meeting. The other distinguished guest was Commander Toublet, who repre-sented the French Embassy. Commander Toublet delivered a most polished address at the Banquet, dealing with the felicitous relations existing between this country and France for the last 150 years. Com-mander Toublet was accompanied by Mrs. Toublet, who won the hearts of all the ladies present, whose guest she was.

Jan 11, 1919

By Andrew C. Katen

The mining industry faces increasing geopolitical risk in the coming decades. Constraints such as resource nationalism, corruption and social license could grow to outweigh fundamental limitations like geology or supply and demand (Ernst & Young, 2013; Verrastro et al. 2010). Lurking beneath these more immediate and palpable concerns, however, may be more significant risks entrenched in geography and history. Deep-rooted cultural and strategic forces that emerge slowly ? or erupt suddenly and unexpectedly ? can generate momentous and far-reaching political, social and economic changes. While multinational enterprises routinely assess for political risk, the nature of minerals extraction means long-term and systemic geopolitical conditions are especially important for mining companies to identify and understand. Mine development is a decades-long process that binds companies to the land and makes changing course to avert emerging threats a difficult and costly option. Consequently, geopolitical assessment is a pertinent and valuable tool that mining companies can use to more comprehensively evaluate strategic threats and opportunities. Geopolitics is the study of society, politics and strategy through the lens of geography (Gray, 1996). Its emphasis on relatively permanent physical features of the earth makes geopolitics a uniquely valuable tool for assessing political risk. Topography, climate and natural resources have shaped, constrained and motivated peoples and governments throughout history. These influences transcend regimes, policies and borders ? and even states themselves ? which, by contrast, change often and dramatically. Framing politics against mountains, deserts and rivers supports identification of historical patterns and forecasts of emerging trends. In other words, the physical map provides an objective and consistent model for studying a subjective and dynamic subject such as politics (Sloan and Gray, 1999). Consequently, geopolitical assessment can highlight threats and opportunities that go unaddressed by other risk methodologies that emphasize current conditions (Glancy, 2012). Taken together, the permanence of geography, hindsight afforded by centuries of political history, and interconnectedness of world events makes geopolitical assessment a valuable approach for conceptualizing strategic risk.

Mar 1, 2014

By Victor Despointes, Stephane Polycarpe, Kathryn Kelly, Chris Feeney, Brian Hann, Vojtech Ernst Gall

The Pawtucket Tunnel is a 2.2-mi, 30.2-ft diameter CSO storage tunnel in Rhode Island. The primary tunnel is built using a dual-mode open-EPB TBM capable of sealing the face within 120 seconds to manage poor ground and water ingress which is launched from within a SEM starter tunnel. The main tunnel connects to four adits along its alignment, three of which are SEM tunnels and one being a MTBM tunnel. This contribution describes the selection process, potential risks, and requirements for the TBM, as well as the design of the main tunnel, the adits, and the adit-bored tunnel connections.

Jun 13, 2023

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By Enrique Levy

Central America is graduating this year into large scale mining with the start up of Inco's multi-million dollar nickel laterite processing plant in Guatemala. In the other extreme of the Isthmus in Panama Texas Gulf Sulphur is doing check diamond drilling and foundation test drilling at the Cerro Colorado copper porphyry. The higher price of gold and silver has spurred development and exploration of several small precious metal mines. The purpose of this presentation is to make a brief resumé of the most important mines operating in the area and a list of significant exploration projects. Also, tables will be shown to compare mining codes and taxes. Unfortunately these tables lack information on Panama. Before starting I like to express my appreciation to Kennecott Copper who permitted the use of some of the data compiled by the author on their behalf during the year 1975. Other persons which did not want to be named also have my gratitude.

Jan 1, 1977

By C. H. Green

. RECENTLY two papers on the structure of eutectics were read before the British Institute of Metals, one by F. L. Brady1 and the other by A. Portevin.2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches; the writer has been working along the same line for some, time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea-of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which, separate out simultaneously (or alternately). From the surface pattern, the eutectic means; a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or. supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the pro-eutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution; (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 2, 1925

By S. Kauvosaari, M. Olofsson, O. Haavisto, M. Kosonen, J. Martikainen

The target in grinding circuit operation is usually to maximise the throughput and energy efficiency while keeping the product particle size on an optimal level for downstream operations. Furthermore, feed ore variations in size and hardness need to be compensated in order to stabilise the process. This is a challenging task for any circuit and requires good instrumentation, combined with careful control design. This study investigates the control of a two-stage iron ore grinding circuit with an AG and pebble mill at LKAB Kiruna KA3 concentrator in northern Sweden. A new control approach based on multivariable model predictive control (MPC) is designed, implemented and evaluated for the circuit. Additionally, advanced instrumentation including a volumetric charge measurement for grinding mills is utilised. The MPC control approach starts with step tests that are used to model the effect of manipulated variables (MVs) like feed rate, water addition and primary mill speed on controlled variables (CVs) such as final product particle size, power consumption and volumetric charge of the mills. In the control implementation phase, the models are then utilissed together with current process measurements and known operating limits to predict optimal future changes for the manipulated variables in order to reach the desired process output values. It is shown that the new control approach improves the stability of the circuit and reduces energy consumption. Keywords: Model predictive control, grinding, optimisation

Jan 1, 2020

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001

By Catherine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his suppher specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation. The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1992

By G. C. Lipsyy

ALL mineral production? of Can11.da is transported in a mine car at some stage during its extraction. There are as many types and varieties of mine cars as there are of mines. Many of the cars in use were developed in the blacksmith shop. Others were designed by engineers and improved by the mine foremen and the mechanics. Every mine car has the ideas of miner, blacksmith, mechanic, and engineer incorporated in it. Many of these ideas are not generally known. This paper was written to make at least some of this information available to the mining industry. In drawings, tables, and notes, it gives all the important details pertaining to the cars. It .does not recommend any particular type of car for any particular piece of work, nor does it present drawings from which a car can be built. It gives the engineer or master mechanic information on many cars which he can apply to his own particular problems. It is hoped that this information will be of use to mine operators. If a few new ideas are conceived as a result of the paper, the author will feel that the effort of compiling it has been worth while. In order to obtain the data for the preparation of the paper, a questionnaire, copy of which is here reproduced, was sent to all the operating mining companies in Canada. An accompanying letter briefly explained the purpose of the paper and asked for co-operation in furnishing as complete information as possible.

Jan 1, 1945

By C. A. Hardie, G. F. Leichtle, J. A. Finch, J. A. Watson

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibres for use in newsprint. The mineral processing group at McGill University, in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network), has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University’s flotation column test work at a Québec wastepaper recycling facility. IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world’s largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and United States municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year, but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World’s solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity."

Jan 1, 1999

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By R. C. Beard

"Heap leaching, currently being applied in the treatment of low-grade ores in the south western United States, is shown to have potential for use in north western Ontario. The history and operation of the process are described, and cost comparisons are given.IntroductionHeap leaching is a simple, low-cost method of recovering gold from low-grade ore. Although it is not currently being used in Canada on a production scale, it is being used extensively, and successfully, in the southwestern United States as well as elsewhere in the world. Especially suited for large deposits of very low -grade ore, it also appears to be practical for use on small, high-grade deposits because it avoids the high capital costs of mills. Eveleth (1980) and others suggest that the capital and operating costs required for heap leaching are approximately 20% and 40% respectively of conventional milling methods.Northwestern Ontario is noted for its large number of undeveloped, small, high-grade gold deposits. Although there are a number o f larger and higher-grade deposits in the area as well, it is the relatively small undeveloped deposits which would benefit most from heap leaching, if it could be demonstrated to be a viable extraction method.To assess the significance of these small deposits, the Ontario Ministry of Natural Resources recently commissioned a consultants' study of the gold reserves in certain parts of northwestern Ontario. This report, titled ""Feasibility of Small-Scale Gold Mining in Northwestern Ontario"", by J.N. Neilson and R.C.E. Bray (1981, OGS Open File Report 5332), documents 106 known gold deposits having sufficient information to calculate gold reserves. A total of over 7.8 million tons having a weighted average grade of 0.19 oz of gold per ton were compiled in the proven, probable and possible categories, with an additional 8.2 million tons in the speculative category. Many of these deposits could be mined by open-pit methods."

Jan 1, 1983