Search Documents

By Xinghai Lei, Yuqi Shang, Guiming Li, Lu He

There are many factors affecting the stability of open-pit mine slopes, among which slopes with soft interlayers have become an important factor inducing deformation and instability due to their poor mechanical properties. In this paper, for the destabilization of a slope with soft interlayer under rainfall infiltration in an open-pit mine in Zhejiang Province of China during the rainy season, a sudden change of displacement at the monitoring point and the formation of a continuous plastic deformation of the slope are proposed as the criteria for slope destabilization through the establishment of a rainwater seepage-stress coupling model combined with the strength reduction method, and by using COMSOL Multiphysics finite element numerical simulation software to establish a three-dimensional numerical model based on the actual mining slope conditions. The safety principle is introduced through the strength reduction method to analyze the stability of the slope with soft interlayer under the coupling effect of seepage and stress. The safety coefficients of the slope with soft interlayer are calculated by using Numerical methods under the coupling effect of seepage and stress. The influence of rainfall intensity and duration on the stability or safety factor of the slope with soft interlayers was studied through analysis of stress, saturation, displacement, and pore pressure evolution. The mechanism of rainfall affecting slope stability was investigated, and the findings were validated using an engineering case study of a slope with a soft interlayer. The findings show that rainfall intensity is the main factor affecting slope stability in the open-pit mine slope with soft interlayer. The higher the rainfall intensity, the faster the shallow soil forms a saturation zone, whereas soft interlayers speed up the process and endanger slope stability. The slope prevention and control technology of the prestressed anchor cable (rod) framework was proposed based on the slope management construction conditions of the mine, and the effectiveness of the measure was verified through on-site industrial tests. The research findings provide a reference for preventing and controlling slope with soft interlayers in open-pit mines under similar conditions.

Feb 20, 2024

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By G. V. Henderson

Large reserves of high calcium limestone have been outlined in the Redwall formation at Nelson, Arizona. Geologic mapping, core drilling and shallow seismic refraction studies have outlined more than 100 million tons of high quality, chemical and metallurgical grade limestone in the Mooney Falls member of the Mississippian Redwall Limestone. Well developed Karst zones in the Redwall were delineated by field mapping, seismic profiling and core drilling. Development of large reserves of high quality, thick beds of limestone near the present mine and rail facilities was the basis for the current mine and plant expansion. When completed in 1978 the planned 1800 Tpd production will represent the largest lime operation in the Western United States.

Jan 1, 1978

By A Jankovic, D David, P Payne

Although the majority of current steel production is supported by iron ore sourced from high-grade haematite deposits, the long-term growing demand for steel has led to higher raw material prices and opened the way for many new magnetite deposits to also be developed. There is a rich and long history of magnetite ore processing in Western countries, including large operations such as Cleveland Cliffs in the USA and LKAB in Sweden, as well as smaller operations like Savage River in Tasmania. The challenge for virtually all magnetite operations is to minimise operating costs, which is dominated by the cost of power required to fine grind the ore in order to achieve acceptable concentrate iron grade together with low impurity content. This remains the case today and will be even more important in the future when a carbon tax is expected to become a significant addition to the operating costs for magnetite deposits. Historically, the lowest operating cost was achieved by multistage fully autogenous grinding with integrated magnetic separation steps between the stages. The major benefit of fully autogenous grinding is the elimination of steel grinding media costs and the need to discriminate between steel and magnetite in coarse magnetic separation. The separation step between grinding stages progressively reduces the amount of material to be ground. Application of more efficient grinding technologies developed in the last 20 years, including high pressure grinding rolls (HPGR) for fine crushing and stirred milling for fine grinding, has provided opportunities to further reduce the operating costs associated with comminution. Both technologies are already implemented in some magnetite processing operations, although in limited capacity. The results of a theoretical option study for high capacity processing of a hard, fine-grained silica-rich magnetite ore is presented in this paper, with the emphasis on comminution circuit options. Several circuit options are ranked based on a net present value analysis incorporating an estimate of carbon tax added in the operating cost. The study demonstrates the significant advantages of applying more efficient autogenous grinding technologies.

Jan 1, 2009

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By Blair K. Salisbury

Dissolution within Permian evaporites of the Delaware basin has created extreme lateral geologic and physical property inhomogeneity within and above the evaporites. Discriminating a sulfur deposit's geophysical signature from other variances is difficult. This is particularly true of porosity-dependent gravity and electrical methods. However, other techniques that detect alteration of strata above sulfur deposits may be applicable individually or in combination with other types of data. Relationships between sulfur deposits and gravity, magnetic, gamma radiation, spontaneous potential, and soil geochemical measurements are illustrated by data from several Delaware basin geophysical and geochemical surveys.

Jan 1, 1992

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By M. W. Fabjanczyk

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth's crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards 'economic self-sufficiency'. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

This paper outlines mining practice in the South Alligator valley between 1954 and 1964. The valley is situated in the Northern Territory 130 miles south east of Darwin and trends north west. The centrally located El Sherana camp is 219 miles by road from Darwin via Pine Creek on the Stuart Highway. 64 miles of gravelled road with low level bridges and culverts which were completed in 1959, connect Pine Creek with El Sherana. This road is often impassable during severe wet season conditions. Earliest recorded production was during the years 1956-57 from the El Sherana and Palette miles, by shallow open cut and cut and fill stoping from small shafts. 4600 tons of high grade ore was processed by hand sorting of massive pitchblende followed by gravity concentra- tion. At the same time 627 tons of ore was won from a small open cut at Sliesbeck 35 miles SE of El Sherana. The second and most important phase of production was to fill two small contracts with the United Kingdom Atomic Energy Authority (U.K.A.E.A.) totalling 700 tons of U 08. About 144,000 tons of ore was mined from widely separated smal' orebodies and mining practice varied from small open cuts to gloryholes, open stoping and cut and fill stoping. In some orebodies a combination of several methods was employed to complete production. Final deliveries were made to the U.K.A.E.A. In 1964.

Jan 1, 1968

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

By Nathaniel Arbiter

There is a history in all men's lives, Figuring the nature of the times deceas'd, The which observ'd, a man may prophesy, With a near aim, of the main chance of things. W. Shakespeare, Henry IV; Part 2 Introduction This nation's first century embraced two stages of the Industrial Revolution. During one, what had been a colonial agricultural economy began to industrialize; water power, then steam after 1794, were the energy sources; coal and iron were the essential ingredients. The second stage started after 1850; aided by rich and diverse mineral resources, the country began its transition from the Iron Age to the Age of Metals. Early civilizations had been built on stone, and fairly high levels were sustained on iron. But the spectacular advances in the past century in communication, in construction, in transportation by sea, rail, land and air, and in much that characterizes modern civilization have depended increasingly on the use of the complete metallic and nonmetallic resources of the earth's crust. Thus it was appropriate to define the Industrial Revolution as “the period during which man's relationship to natural resources became utterly changed”, 1 with minerals playing a major and indispensable role. But we are now becoming aware that the relationship of man to natural resources must change again. On every hand the dangers inherent in the contamination of land, sea and air by the wastes of civilization are becoming apparent. And from the growing realization that mineral wealth is finite must eventually come other far reaching changes in mineral use and distribution. For on the scale of centuries we cannot continue to exploit mineral resources even at present rates, let alone at expanded rates, without eventual depletion of the more abundant resources, and early exhaustion of the less abundant. In the past our problems were relatively easily met by the development of new and improved machinery and processes. But the future will

Jan 1, 1971

By S. Kline

The compositions of metamorphic minerals of the south limb of the Dore Lake Complex have been determined by microprobe techniques. Mineral assemblages typical of the greenschist facies occur in Mg-rich bulk compositions, but in Fe-rich rocks albite-epidote amphiboli te facies assemblages occur. Low oxygen fugaci ties and a general paucity of metamorphic fluids prevailed in most of the complex, but a higher oxygen fugacity is indicated near the Chibougamau Pluton, and a local abundance of C0z and Cl in fluids near the pluton is suggested by the presence of scapoli te. The metamorphic gradient overprinted on the complex near the Grenville Front is apparent in mineral chemistries as well as by the appearance of garnet. Chlorite becomes richer in Mg, and iron is fractionated more strongly into hornblende. The amphibole also increases in Alz03.

Jan 1, 1984

By A Garvie, D Kentwell, J Chapman

"Most new mining projects require an initial assessment of the locations and volumes of potential acid forming (PAF) waste that is likely to be moved and dumped in surface waste stockpiles. This requires sampling of the waste rock zones and submitting the samples for a series of tests. Key to the outcome of the waste characterisation process is obtaining sufficient samples that are representative of the various rock types both in number and spatial distribution.Various regulatory bodies throughout Australia and the rest of the world are currently struggling with how to define minimum amounts of sampling to achieve realistic estimates without imposing excessive costs and time constraints on a project.This paper addresses two aspects of the process: what constitutes a æsufficientÆ number of samples how to use those samples in determining volumes of likely PAF material.Geostatistical methods of characterising orebodies with large numbers of samples are routinely used in the mining industry by geologists and geostatisticians to estimate and classify Mineral Resources. In theory exactly the same methods can be used to estimate PAF waste locations and volumes.In practice the number and spatial distribution of dedicated PAF waste samples at feasibility stage is typically so small that it is almost impossible to estimate the spatial distribution of PAF material with any degree of confidence at all. Consequently, the common approach is to characterise a few samples from a lithological unit and then assume that they represent the unit as a whole. This approach, however, can be fraught with risk.This paper describes some of the findings of SRKÆs evaluation of several coal projects with respect to PAF waste evaluation and highlights some common misconceptions held by people working in this area that do not have a knowledge of statistics or geostatistics.CITATION:Kentwell, D, Garvie, A and Chapman, J, 2012. Adequacy of sampling and volume estimation for premining potential acid forming waste evaluation using statistical and geostatistical methods, in Proceedings Life-of-Mine 2012, pp 79-88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012