Search Documents

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009

By F. J. Klingler, R. Hausmann, K. M. Swaffar, J. C. Neyer

This paper presents the results of a study of case histories of projects on which sinking caissons were used to construct shafts for tunnel construction and other underground works. Design methodologies are reviewed with respect to the impact of soil and groundwater conditions on the performance and constructability of sinking caissons. Factors which have led to success or failure are reviewed and evaluated, and recommendations for future investigation, design and construction activities are presented. Cost data for five recent projects are reviewed and compared to the cost of shaft installation by other means.

Jan 1, 1997

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By David Laing

Completion of a Feasibility Study represents a major milestone in the development path of a mine, and one which typically triggers a need for project financing. Obtaining funding for construction relies on a positive Feasibility Study and a host of other related activities. This paper looks at the financing process and work required to support it, during and after the Feasibility Study, and bring it to a successful closing. It will include comment on the significance of permits, environmental plans, construction contracts, offtake arrangements, hedging, insurance, and others requirements to support a financing plan.

May 1, 2010

By William J. Kemnitzer

This study was made to show the growth of petroleum coking and to deter- mine trends and characteristics of marketing and utilization of coke on the West Coast, comparing these data with those of the United States as a whole. An earlier Bureau of Mines economic survey of petroleum coke was made in 1930 before the widespread use of coking processes. Data, derived from published and unpublished literature as well as from interviews with industry representatives, show a marked increase in the production of petroleum coke since the end of World War II. This increase resulted from the need of refiners to upgrade heavy residuums for which the demand was diminishing. Increasing coke production as well as significant market shifts away from California-produced coke have created excessive stocks of petroleum coke on the West Coast. The causes of these market shifts were based mainly on (1) economic factors and (2) certain undesirable qualities of some of the petroleum coke produced in California.

Jan 1, 1965

By William J. Kemnitzer

This study was made to show the growth of petroleum coking and to determine trends and characteristics of marketing and utilization of coke on the West Coast, comparing these data with those of the United States as a whole. An earlier Bureau of Mines economic survey of petroleum coke was made in 1930 before the widespread use of coking processes. Data, derived from published and unpublished literature as well as from interviews with industry representatives, show a marked increase in the production of petroleum coke since the end of World War II. This increase resulted from the need of refiners to upgrade heavy residuums for which the demand was diminishing. Increasing coke production as well as significant market shifts away from California-produced coke have created excessive stocks of petroleum coke on the West Coast. The causes of these market shifts were based mainly on (1) economic factors and (2) certain undesirable qualities of some of the petroleum coke produced in California.

Jan 1, 1965

By FRANCIS FEEHAN

Safety first is no longer merely a motto ; in some industries and in some parts of the mining industry it is an accomplished fact . In connection with the National Safety Competition of 1928 in which 284 mines and quarries participated , 42 plants were operated without a single lost - time accident . The winning company in the bituminous group had an accident severity rate of 0.053 per thousand man hours of exposure . Excellent safety records of various kinds are becoming more and more frequent , and the indication is that in reality safety is first in many mines and qquuaarrrriieess .. The safety achievements in the Stewart mine of W. J. Rainey , Inc. , are unusual even among mines winning awards in the competition .

Apr 1, 1930

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

By D. Harrington

The record of fatalities from mine explosions in the United States during the fiscal years 1934 to 1937 wars the best in the history of the mining industry; that for the fiscal year 1939, however, is not so favorable, since nearly as many men (170) were killed by explosions in 1938 as were killed during all of the previous 4 years (182). In spite of the large increase in fatalities from explosions during 1938, the average for the past 5 year period (70.4) is less than one-half the average (13) of the preceding 5 year period. The reasons for the large increase in the number of explosion fatalities during the 7 past year as compared with the previous 4 year are not entirely clear; it is: evident, however, that in some instances there has been laxity in the enforcement of State minim laws, and also that come of our coal-mining people, including workers and operating officials, have failed to carry out tine known precautionary measures to prevent explosions.

Jan 1, 1939

By A. J. Jager, D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2004

By Rita D. Sylvester

"IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January I, 1965, to December 31, 1969. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January I, 1960;' the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January I, 1960;3 the 5-year list of Bureau publications and articles from January I, 1960, to December 31, 1964.' It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1965, to December 31, 1968, as well as the Bureau publications and articles for 1969."

Jan 1, 1970

By Catharine T. Fogg

The U.S. Bureau of Mines investigated the availability of platinum, palladium, and rhodium from 16 deposits in four market economy countries (MEC's). Major recoverable products include 164 Moz of platinum, 80 Moz of palladium, 13 Moz of rhodium, 24 Moz of ruthenium, 4 Moz of Iridium, 2 Moz of Osmium, and 10 Moz of gold. The 12 deposits in the Republic of South Africa are estimated to account for 96.7 pct of total recoverable platinum. The base-case scenario estimates the long-term cost of production including recovery of capital, but provides no return on the investment or O-pct discounted cash-flow rate of return (DCFROR). The total production costs in January 1990 U.S. dollars ranged from $325/oz to $1,288/oz of platinum compared to an average January 1990 price of $492/oz. Approximately 83 pct of total recoverable platinum was economic at a cost level of $4S0/oz or less. At the IS-pct DCFROR, only 26 pct of total recoverable platinum was economic. For platinum-group metals (PGM), attention has been focused on the ratios of the three primary metals: platinum, palladium, and rhodium. Sensitivity analyses were performed to determine the impact long-term rhodium price increases could have on the total cost of production for platinum and palladium.

Jan 1, 1993

By Steven D. Botts

The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd. , is a $2.3 billion copper/zinc project, located in the Ancash Department in Perú. The project consists of an open pit mine, a 70,000 ton per day concentrator, a 302 Km. long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 million tonnes per year of copper and zinc concentrates over a 23-year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world. This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28th, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14th, 2001 by Peruvian president Alejandro Toledo. The construction stage of the project generated 8,000 direct jobs, with a peak of 10,000 employees, and 30,000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals; around 30% of whom came from the department of Ancash where the deposit is located. Approximately 5,800 indirect jobs will be generated from the project. Independent sources state that Antamina will increase the Peruvian mining exports by 30% and Peruvian GDP by 1.4% within its first year of full operation in 2002. Since winning the privatization bid for the project in 1996, the company has implemented a successful approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company?s environmental program. Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues, and as a result, has set new standards in Perú for environmental and community management, and sustainable development.

May 1, 2002

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By Denise Crocce Romano Espinosa

The recycling of waste of electric and electronic equipment (WEEE) is one of the main modern challenges. Among the variety of WEEE, batteries can be set apart due to their composition and their growing demand along with portable devices. The objective of this work is to characterize the thermal behavior of a sample of mixed types of batteries using a thermobalance (TGA). The results of tests showed that Cd evaporated up to 800ºC, Zn evaporation occurred mainly above 900ºC and manganese oxides were pre-reduced to MnO at temperatures above 900ºC.

Jan 1, 2009

By Gordon M. Matheson, David K. Miller

Possible impacts to the water quality and production capacity of ground water supply wells by blasting is a common cause of complaints for blasting contractors, mining companies, and local regulatory authorities. The major complaints of changes in well water quality include; turbidity, discolored water (red, brown, black, yellow and milky water), and nitrate and/or coliform contamination. The major complaints for changes in well water production capacity include: loss of quantity production, air in water and/or water lines, damage to pump, and damage to well screen or borehole.

Jan 1, 1997

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006

By J. M. West

Expanded war in Viet-Nam overshadowed activities in the Far East in 1965, diverting capital and materials from potential regional development projects. Japan with-stood a period of business recession that was particularly felt by its coal mining and iron and steel industries. Toward yearend signs of improvement began to show. Despite the recession with attendant credit restrictions and forced cutbacks in areas of overproduction, Japan's overall industrial output rose nearly 5 percent during the year. Foreign trade, liberalized in 1964, was a strong point in the Japanese economy and took the place of lagging domestic demand. Japan maintained its third place in world production of iron and steel ahead of West Germany and in 1965 was the world's fore-most exporter of iron and steel in primary and semimanufactured forms. Economic setbacks in mainland China caused by its "Great Leap" failures and subsequent withdrawal of Soviet technical assistance were difficulties relegated to the past. However, a newly formed "Red Guard" political group, part of a so-called cultural revolution, was due to cause new disruptions in 1966. Nevertheless, significant gains were claimed in Chinese industry, and the country approached self-sufficiency in petroleum in 1965 by virtue of its Tach'ing oilfield. Restoration of friendly relations was achieved between South Korea and Japan accompanied by Japanese offers of industrial aid and increased trade. Indonesia's economy was deteriorating; the country withdrew from regional development organizations and continued its stubborn confrontation policy against Malaysia throughout 1965. Late in the year after a Communist uprising had been quelled, there was a period of political retrenchme t and it was hoped that economic improvements would follow. Petroleum remained a strong area in Indonesia's varied resources, and its production was increasing. Tin output declined, however, because of operating difficulties.

Jan 1, 1967

By J E. (Boet) Coetzee

SAFEX International, as the name suggests, is a global organisation, which has the fundamental objective of improving the safety of operations concerned with the manufacture, storage, transport, and use of commercial and military explosives and pyrotechnic products throughout the world. It is a nonprofit making organisation of manufacturers of explosives from all parts of the world, founded in 1954 with the aim of exchanging experiences within the explosives industry. Every third year SAFEX organises a Congress during which members present papers on selected themes and discuss reports of significant incidents that occurred since the previous Congress. Admission is for SAFEX members only, thereby creating a safe environment for discussing problems “within the family”. The XV Congress will celebrate the Association’s 50th anniversary in Geneva where it was founded. An overview of the Congress indicates its structure and covers aspects such as the training event, technical seminars and the themes for the plenary sessions and associated workshops. The paper also highlights the special event for the chief executives of member companies and the review of incidents that occurred in the industry since the last Congress. The Congress concludes with a social programme for delegates and their partners on the last day.

Jan 1, 2005

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009