Search Documents

By A R. Proudman, A H. Purvis

The Granites Gold Mine Callie gold deposit is located 550 km northwest of Alice Springs in the Tanami Desert. Gold mineralisation occurs due to a complex interplay of geological factors which include but are not limited to favourable lithology, structure, alteration and quartz veining. High-grade mineralisation, while pervasive under favourable conditions, is highly variable over short distances and is very nuggetty. In contrast, the lithology and geological structures that host the mineralisation are very continuous. Orebody modelling techniques have evolved over time because of a growing understanding of the mineralisation controls. Modelling issues such as sampling and assaying accuracy, modelling method, data density, gold population statistics, geological interpretation and domaining, grade boundary and calculation conditions, and model block size are constantly being reassessed in an effort to increase understanding of the mineralisation controls and modelling accuracy. The evolution of the modelling process in response to increasing data levels and a growing understanding of the mineralisation controls has resulted in changes to the perception of the orebody size and style. This has caused the choice of underground mining method to be revised several times and the process to final mining method selection to take longer than usual. In order to achieve the planned production start-up date of July 1998 the process has been allowed to progress in parallel with development of the underground mine. This paper describes the resource modelling and mining method selection process applied to the Callie underground mine and some of the issues which have contributed to its evolution. Some conclusions that are relevant to the efficient planning and development of new mining projects in general are presented.

Jan 1, 1998

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009

By Kelvin K. Wu, George H. Gardner

On July 24, 2002, a nonfatal entrapment accident occurred at the Quecreek #1 Mine, Black Wolf Coal Company, when an active mining section inadvertently cut into a flooded abandoned mine. This incident, and the dramatic rescue which ensued, brought national attention to a common problem in the coal mining industry. Since 1995, there have been more than 100 inundations at coal mines in the United States. Unavailable, inaccurate, or incomplete mapping of older abandoned mines is typically responsible. Serious problems associated with accidental discharges of fluid mine waste material (slurry) and water from coal refuse disposal facilities have resulted from similar causes. Recent problems related to the inaccurate location of old abandoned mine works have increased the interest in the use of conventional and emerging drilling and geophysical techniques for detection of air-filled and water-filled cavities. The United States Congress has committed significant funding toward investigating the applicability of these technologies. MSHA actively promotes the use of the best available technology to minimize the significant adverse safety and environmental consequences associated with unplanned breakthroughs and inundations. This paper provides background information and a general summary of the MSHA-sponsored field demonstration projects which are currently in progress. Potential benefits and limitations are discussed. The need for field verification/ground-truthing is emphasized. Under appropriate conditions, geophysical methods can be effectively integrated into a comprehensive field exploration program.

Jan 1, 2005

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

By S. J. Neethling

The flotation froth structure and motion determines the amount of entrained gangue that is collected to the concentrate. Despite this important role in the overall performance, the behaviour of the froth is still ill understood. To date, predominantly empirical models have been developed to describe entrainment. A fundamentally based model is described and used here in an attempt to improve the understanding of entrainment. This general froth simulator (UMIST FrothSim) allows the modelling of a wide range of flotation conditions, as it takes account of a large number of the physical phenomena that occur within flotation froths. The model firstly describes gas motion and bubble coalescence, and the water motion based on gravitational, viscous and capillary effects. The motion of the solids distinguishes between various solids classes based on hydrophobicity, particle size and density and models them by including the effects of Geometric and Plateau border dispersion, particle settling and the motion of the water. The aim of this paper is to show the applicability of this model to explain the observed entrainment and collection of gangue. This is done by comparing model predictions with the experimentally observed relationship between the gangue and water recoveries. The model predicts the identical trends, which are explained in terms of the interaction between the linear effects of water motion and hindered settling and the non-linear effect of particle dispersion.

Jan 1, 2001

By E. B. Olds

This paper describes the methods and costs of deepening the 3-compartment underground shaft in the Hooper Tunnel adit at the Bunker Hill & Sullivan Mining and Concentrating Company Crescent mine in the Coeur d'Alene mining region, 7 miles east of Kellogg, Shoshone County, Idaho. The work was done with the aid of a Defense Minerals Exploration Administration contract (No. Idm-E493, Docket No. DMEA-2764). Preparation for deepening the shaft was begun March 26, 1953, and sinking was completed May 27, 1954. The shaft, bottomed at 1,275.5 feet in 1939, was deepened to 3,276 feet, using mechanical mucking and intermediate pockets. A total of 50,349 man-hours was required to complete the work of sinking 2,000.5 feet, cutting 7 pump stations, and driving 2 pocket raises. The rate of advance was 7.1 feet of shaft per operating day, or 8.4 feet per day of actual sinking. The total direct cost for sinking was $205.20 per foot.

Jan 1, 1957

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

Coal-bearing regions cover about 18,464 square miles or one third of Iowa, primarily in the south-central part of the state. Coal quality ranges from subbituminous to high volatile bituminous. Iowa's coal reserves are estimated to be 2.2 billion tons, less than one-half of one percent of total U.S. reserves. Coal beds are typically thin seams with a maximum thickness of five feet. Coal deposits in Iowa were fist mined in the 1840s for blacksmithing and domestic purposes. Demand for coal increased with the use of coal to fuel steamboats and railroads. Production peaked in 1917, when Iowaproduced9 million tons of coal. Since then, conversion to natural gas and fuel oil has decreased the demand for coal. Today, electrical power generating plants have created a continuing, but declining, demand for Iowa's coal. Coal production in Iowa is by surface mining methods. The Iowa regulatory program was conditionally approved January 21, 1981. Full approval was received March 28,1982, and the Abandoned Mine Land Program was approved March 28, 1983.

Jan 1, 1992

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Douglas F. Scott

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the Pyramid RARE II area (No. 5023) covering 23,500 acres (9,500 ha) of E1 Dorado National Forest and 7,900 acres (3,200 ha) of the Lake Tahoe Basin Management Unit (fig. 1). The Bureau of Mines investigation did not reveal mineral deposits in the area. Samples taken from silicified and limonite-stained metasedimentary rocks and aplite dikes were void of precious or base metals or uranium. Placer samples from stream gravels contained no gold values. Molybdenite occurs in quartz stringers within quartz monzonite near Grass Lake, adjacent to the area; no extension; were found in the area.

Jan 1, 1982

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By A. G. B. Hayes, C. L. Renzoni

"AbstractThis paper provides a rough outline of economic expectations for the near future and then goes on to discuss their effect on the expected demand for metals, using zinc, copper, nickel and aluminum as detailed examples.IntroductionMINING, as you are all painfully aware, is a cyclical business. We believe that it will remain so as long as there are economic cycles.The fortunes of the industry are tied to those sectors of the economy where decisions can be postponed until more favourable times: automobiles, housing, appliances, inventory building and capital spending. Over the past two years, while U.S. GNP fell by 3.8%, automobile production declined by 31 %, from 9.7 million units in 1973 to 6.7 million in 1975. Housing starts plummeted some 43% from 2.1 million units in 1973 to 1.2 million in 1975. Little wonder that U.S. copper consumption fell by 37% and zinc consumption by 38% over the same period.With the rest of the world's economies moving in unison with that of the United States, it is also not surprising that times have been tough for mining.Arthur Burns, chairman of the U.S. Federal Reserve, contends that each recession sows the seeds of its own recovery. The worse the recession, the better the subsequent recovery. If this is true, then the lot of the mining industry should improve significantly over the next two to three years."

Jan 1, 1977

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By Frank P. Frandina, Diane R. Hirsch, David P. Field, Colin R. Weeks

To accommodate growth in air service and to follow the Master Plan for long-term airport development, the Metropolitan Washington Airports Authority established thed2 Development Program at Washington Dulles International Airport. A sub-surface Automated People Mover (APM) System is under construction to replace the Mobile Lounges as the primary people mover system at Dulles. To minimize disruption to airport operations the majority of the APM System’s crossings of Taxi lanes will be undertaken using Tunnel Boring Machines (TBM) or the New Austrian Tunneling Method (NATM). This paper explores the planning and design of these shallow tunnel segments for future generation aircraft loads, within the constraints of minimal construction access under post 9/11 security requirements and the context of the overall airport expansion program.

Jan 1, 2005

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

Jan 1, 1967

By He De-wen

The influence of wastewater containing benzene from chemical industry by technology combined blow-off with Fenton reagent oxidation was experimentally studied. The present results suggest that the technology combined blow-off with Fenton reagent oxidation can effectively remove benzene pollutant in wastewater. The main factors that influence the removal benzene such as temperature and blowing time and volume, pH and reagent dosage of H2O2 and Fe2+ are studied and the optimal experimental conditions are as follows: time 20min, temperature 40i, air-blowing volume 0.4L/min, pH value 5, and H2O2 and Fe2+ dosage 2mL/L and 200mg/L respectively. Under the above conditions, benzene pollutant can be removed up to 97%. Compared to other removal ways of wastewater containing benzene, the technology combined blow-off with Fenton reagent oxidation is more effective and has the advantage of high speed.

Jan 1, 2009

By Rob Farnfield, Yuill Gavin

The rock blasting industry continues to be under pressure to reduce the level of vibration induced by the use of explosives. In recent years much research and development has been directed to minimizing vibration levels by controlling the delay period between blast holes. The most commonly applied technique is known as Linear Superposition. This technique takes the vibration produced from a single-hole test shot and simulates the vibration that would be produced from a full-scale production blast. The simulation can be run with various delay periods and the optimum delay chosen. The success of the Linear Superposition technique depends to a great extent on having accurate delay detonators and on the single-hole test shot reliably indicating the vibration signal produced from each hole in a production blast. A quarry-based case study is given illustrating how these assumptions are not always valid. In this case the use of electronic detonators has controlled frequency but not vibration level. The paper goes on to describe a series of single-hole test shots in an U.K. limestone quarry. The vibration 2 signals recorded are examined in terms of variations in free-face provision, blast geometry, explosive properties, etc.

Jan 1, 2001