Search Documents

By A. H. A. Robinson

Until quite recently-practically up to the present time-all but an insignificant amount of the copper produced in Canada was shipped abroad in the form of ore, matte, blister, etc., there to undergo the further treatment necessary to bring it to the refined state in which it is required by fabricators of copper. Consequently, Canadian manufacturers were forced to import nearly all the copper required in their business; and a considerable portion of the ultimate value to be derived from a Canadian raw material was lost to the country of its origin. In the early days of Canadian copper mining, when both the production and consumption of copper in Canada were much smaller than now, such a condition of affairs was perhaps economically unavoidable, and, in any case, was not a matte~ of sufficient importance to attract general attention. Later on, however, when there had been large and rapid increases both in the production and consumption of copper in Canada, it formed the basis of much adverse criticism, deserved or not, of producers of Canadian copper-criticism that became intensified during the war and subsequent years. Happily, the chief grounds of complaint have now been removed, and there are today copper refineries in Canada, either operating or under construction, that are capable, in the aggregate, of turning out amounts of refined copper greatly in excess of any indicated Canadian consumption.

Jan 1, 1931

By Robert C. Dyni

The Bureau of Mines in cooperation with the Solution Mining Research Institute conducted surface and subsurface investigations over five solution-mined salt cavities in the Hutchinson, KS, area. The purpose of these investigations was to determine the mechanisms that lead to the formation of sinkholes above collapsed solution cavities. Of the five salt-solution cavities investigated, four had collapsed and produced sinkholes prior to the time of the investigations; the fifth cavity was considered stable. Exploratory drilling and coring operations were conducted at all five sites; surface stability monitoring was conducted at three of them. The results of these studies indicate that excessive dissolution at the salt-shale contact of each collapsed cavity produced large, unsupported roof spans that ultimately exceeded the structural integrity of the overburden. The stable cavity was not exposed to excessive dissolution at the salt-shale contact; this limited the roof span and ensured a stable cavity. The data also show that surface settlement in the vicinity of the two surface-monitored sinkholes continued for approximately 7 years after the sinkholes formed, indicating that the rubble piles of the collapsed cavities were undergoing gradual consolidation.

Jan 1, 1986

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980

Jan 1, 1882

By Larry Mirabelli, David Lilly

In 1777, the French naturalist, Georges Louis Leclerc, Compte de Buffon developed a statistical technique to estimate the width between two parallel lines by randomly throwing a needle at the two lines and counting the number of times the needle intersected one of the two lines. By knowing the length of the needle, the distance between the parallel lines could be estimated. This analysis was named the “Buffon’s Needle Problem”.

Jan 1, 2008

By WL Wagner

This report presents a quality control approach to the derivation of strategies for monitoring a work environment; specifically, the environment in underground mines where diesel-powered equipment and blasting agents are used. The approach is presented as a series of 22 steps called the Monitoring Strategy Development Scheme. The scheme is an orderly method for selecting from a number of options a strategy or tactics to cost effectively meet the requirements of a chosen objective related to the monitoring of breathing zone air quality. The scheme provides a format to quantify many of the factors that influence the selection of on strategy or tactic over another, and to ensure that important considerations are not neglected. The premise that breathing zone air in work environment can be considered to be manufactured product and that, therefore, conventional quality control approaches are applicable, is introduced. Typical approaches to the quality control of manufactured products and how these approaches can be applied to the selection of monitoring strategies are discussed.

Jan 1, 1983

The Black Hills Mineral Atlas briefly summarizes all important data available on the mines and mineral deposits in the Black Hills that have been explored, developed, mined, or located. The purpose of the atlas is threefold; First, from available data the general potentialities of the Black Hills region can be determined, although it is not possible to calculate actual ore reserves; second, it will provide the necessary basic information regarding a given property or commodity for further detailed study; and third, the compilation is a comprehensive directory of Black Hills deposits.

Jan 1, 1955

LOCAL COMMITTEE OF ARRANGEMENTS. Major J. W. Powell, Chairman; F. P. Dewey. Secretary; S. F. Emmons, A. S. Hewitt, J. P- Hilgard, Charles Knap, and F. W. Taylor. THE opening session was held in the hall of the new National Museum, on Tuesday evening, February 21st. President Metcalf introduced General W. T. Sherman, one of the Regents of the Smithsonian Institution, who read the following address: ADDRESS OF GENERAL SHERMAN. MR. PRESIDENT AND GENTLEMEN : I have been invited to meet you here this evening to extend to you the cordial greeting of the regents of the Smithsonian Institution, and to assure you that they are most happy to have it in their power to place at your disposal this beautiful hall, dedicated to science and art. This National Museum is the property of the United States, of which the regents of the Smithsonian are simply the custodians, and the board has delegated to its secretary, Professor Baird, the right to extend its use to the National Academy of Sciences and like kindred societies, among which we are glad to class the Institute of Mining Engineers. It is eminently fit that you should meet here at this, the nation's capital, under a roof partly your own, devoted to natural sciences, and in the shadow of the Smithsonian, founded for the exclusive purpose of collecting and diffusing knowledge among men. Of all the workers employed on earth no single class seem to me more worthy the respect of their fellows than those who seek beneath the surface for the useful minerals and metals which contribute so largely to the wealth and comfort of mankind. In no branch of human industry does intelligence come so immediately in contact with labor. To the mining engineer chemistry, mineralogy, and geology are as reading, writing, and arithmetic to the merchant;

Jan 1, 1882

By John A. Davis, David W. Brunton

During the past few years great progress has been made in the United States toward safer, more efficient, and more economical tunneling methods. This advance is partly due, no doubt, to the recent increase in the number of tunnels and adits driven for devel- oping and draining mines and transporting ore. The Bureau of Mines during 1911 and 1912 made a special examination of this phase of mining operations, in connection with an investigation of mining methods and means for preventing accidents. The details especially studied were the provisions for the safety of employees, the kinds of equipment, the methods of driving, and the costs of con- struction. The results and conclusions obtained from that investi- gation are discussed and summarized in this bulletin. Up-to-date information concerning tunneling methods is difficult to obtain. There are few books on the subject; and much of the material they contain, although interesting and of value historically, is now obsolete. The engineering periodicals, it is true, endeavor to keep abreast of the times, and several in nearly every issue present some article bearing upon tunnel work. But the very multiplicity of these articles prevents one from reading them all, and the foreman or superintendent in charge of a tunnel, or the mining engineer designing one, and especially the business man financing the project, has no time for a lengthy search after scattered articles in order to determine the present status of tunnel work. Then, too, knowledge of new methods travels slowly. Valuable inventions and improve- ments in tunneling as well as in all the other industries frequently remain in the notebook of the investigator, or as theses are buried in university libraries, or are published only in journals of small scien- tific societies. New tunneling methods and equipment that are prov- ing safe, efficient, and economical may be totally unknown outside the district in which they originate. This paper, based on a special examination both in the field and in engineering literature, is in- tended to supply data concerning modern and recent tunneling practice in the United States, and to make suggestions that, it is hoped, will result in a saving to the mining industry of energy, capital, and life.

Jan 1, 1916

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By E Mare

Recent highly publicised incidences of disastrous containment failures, none more pertinent than the 2019 iron ore tailings dam failure in Brumadinho, have focused the world’s attention squarely on the often-challenging subject of tailings storage. Unwanted ultrafines, that are deemed to be unworthy of further treatment or not to have further saleable value, are therefore a significant issue for mine owners looking to reduce risks and perceptions associated with long-term storage of tailings. In this context, there are strong drivers to identify safer approaches to ultrafine tailings management, especially if it can also lead to increased revenue, together with better water stewardship and environmental outcomes. The better management of tailings needs to be considered from both containment challenge and processing opportunity perspectives. This paper focuses on the latter, reviewing from a technical and economic perspective, the feasibility of more extensive processing and/or reprocessing of specifically iron ore tailings, in a bid to reduce the overall volume for management in long-term storage. Herein the opportunity lies in recovery processing, as much as enhanced thickening and/or mechanical dewatering, and therefore the paper discusses both issues as equally important sides of the same coin. Recent interest in iron ore ultrafines processing and reprocessing studies suggests that the enhanced processing of iron ore tailings offers multiple perceived advantages. Apart from a potential reduction in tailings volume, associated with safer containment, lower environmental impact and improved water management, the prospect of increased revenue from additional Fe recovery presents supplementary motivation for iron ore players to embrace this approach, as further elaborated in this paper.

Nov 8, 2021

By M. J. H. Ruscoe

"The circulation wear rates of pure nickel, cupronickel and nickel-plated-steel coins were measured and found to be in the ratio 1:3:1 . The relative wear rates of nickel and cupronickel coins were similar to those reported in earlier studies, and the circulation wear data for nickel were used as a reference in laboratory wear tests. A correlation between circulation wear rates and laboratory wear rates formed the basis for a prediction of service life using relief legibility as an 'end of life' criterion. This criterion was determined to be an average surface thickness loss of 12 um. The surf aces of nickel and Nickel-Banded-Steel (N-B-STM) coins were observed to harden both in circulation and in the laboratory tests at a rate of approximately I VHN/year of actual or simulated service life. It was also observed that the laboratory wear rate of N-B -S coins increased as nickel cladding thickness increased and this effect was attributed to differences in surface hardness.Wear test results are also reported for the new Canadian dollar coin material which shows a better wear resistance than pure nickel. IntroductionThe subject of coinage wear has a long history, and a number of studies have been published, concerned both with the measurement of circulation wear rates and with accelerated laboratory tests to simulate the behaviour of coinage materials in service. As early as 1803, wear tests were conducted by Hatchett on gold coinage using various types of vibratory and tumbling machines». These tests were commissioned by King George III of England who was concerned about the wear of gold coins in circulation.Early in this century, Adrian performed laboratory tests that showed that the wear rates of cupronickel 75/25 and nickel coins were in the ratio 3:1 and this ratio was later confirmed in laboratory tests reported by Daeppen and Zurrerw, The latter authors also weighed cupronickel and nickel coins that had been in circulation for various times and observed the same 3: I ratio. There was further support from Tylczak and Blickensderfer who reported significantly higher abrasive wear rates for cupronickel compared to nickel, when rubbed against sand paper."

Jan 1, 1988

By George C. Stone

WHEN George C. Stone, a Director of the Institute, and so well known to our Members in connection with the Institute's many activities was abroad in 1.919, he secured an interesting collection of these coins, which appeared in Zinc, a publication by the New Jersey Zinc Co. Regarding this collection of coin, Mr. Stone says: "During the war, all gold and most of the silver disappeared, making small change very scarce. As the French Government was fully occupied by the war, it allowed various Chambers of Commerce and other bodies to issue money, both paper and coins. Many of the latter were made of zinc, and I secured several while in Paris. We had all heard of the Belgian and German zinc coins, but I imagine few knew how many different kinds there were. The accompanying plates show both sides of those I got. I took all that the dealer had; but he said that there were a number of others in existence. The coins in the bottom line were issued by the Germans in Belgium during the war and all are still in common use. The first two in the next to the bottom line are German. All of the others were issued by Chambers of Commerce or corporations. A few have been nickel plated; these look and wear much better than the others. "Coins" made of pasteboard were also issued by similar bodies, also notes.

Jan 1, 1920

By M Scott, J J. McEwan

Silver and silver alloys tarnish readily by the formation of tarnish on the surface when exposed to a wide range of sulphur-containing atmospheres. This tarnish is unsightly and undesirable and can be removed either with a silver polish or a chemical dip. Polishes are, however, not suitable for irregular and embossed surfaces such as on coins, medallions and jewellery items, because of uneven removal of the tarnish layer and excessive wear. Successful tarnish protection can be achieved by either storing the items away from the aggressive atmosphere or by coating/treating the exposed surfaces with a protective layer. Storage is feasible for collections but is not suitable for items that are handled or worn regularly, such as jewellery. A number of commercial coatings and treatments have been developed, but to date there has not been a systematic evaluation of tarnish protection. This paper details the performance of a range of generic coatings in an accelerated tarnish test. The degree of tarnish was evaluated by means of loss in reflectivity and change in colour. Four coatings/treatments improved the tarnish resistance of silver by more than tenfold. These include an organic lacquer, rhodium electroplating and an organic self-assembled monolayer (SAM) conversion coating. Research is continuing to optimise these coatings. Keywords: silver alloys, tarnish resistant coatings, silver polishes.

Jan 1, 2006

By Paul T. Allsman, William H. King

This paper describes the mineral deposits and discusses mining and milling methods and related operating conditions in an important gold , silver , lead , and zinc producing area in Ouray , San Juan , and San Miguel Counties , Colo . , embracing 250 square miles . The area is extremely rigged , ranging in altitude from 8,000 to 14,000 feet . White men first penetrated the area in 1860 , when a group known as "Baker's party " reached the Animas River at the present site of Silverton . Difficulty with the Ute Indians and severe winter conditions forced the group to leave and discouraged prospecting until 1870 when a second party reached the area and succeeded in producing 27 tons of ore yielding $ 150 a ton in gold . In 1874 , a treaty with the Indians opened the way for settlement , and mining was established . The total production of recovered gold , silver , copper , lead , and zinc from 1873 to 1947 in the three counties is valued at $347,057,047 . The greatest amount of the total production of metals has come from quartz veins in a series of volcanic flows and tuffs covering the area and comprising a blanket 4,000 to 6,000 feet thick . The igneous rocks were laid down upon an old , erosion surface and are underlain by Paleozoic and Mesozoic sedimentary rocks and pre - Cambrian metamorphic rocks . The entire series has been intruded in late Tertiary time by volcanic dikes and larger intrusive masses . Because of the great differences in relief generally , mining is con-" ducted through long adits to a depth of nearly 3,000 feet below surface in places . Walls of the veins generally stand well , and shrinkage stoping is the most common method of mining . As virtually all of the ore is sulfide below the zone of oxidation , flotation is the common method of milling . Generally , where gold is important , provision is made for its removal by jigs . Bulk concentration of the sulfides is practiced at smaller mills , but the larger operations make a selective lead and zinc concentrate or a lead , zinc , and copper . concentrate . ·

Mar 1, 1950

By B. G. Russell

A wide range of minerals is found within the Republic of South Africa, many of which are exploited to a greater extent than in similar deposits found elsewhere. It is often asked whether this is atributed to the high grade of the ores encountered in this country, or whether such factors as fiscal and Infrastructural incentives create an economic climate that has en bled the mining industry to successfully extract and market minerals at a profit. This paper views South Africa's mineral resources in a regional and global context In an attempt to place the country's geological wealth in perspective. It represents the author's own Views, and not necessarily those of the Department of Mine al and Energy Affairs.

Jan 1, 1986

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By Robert M. Becker

This report (the second in a series of five) presents the mathematical development in extending the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The probability distribution functions (those here called the compound binomial and compound multinomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, while finite population moments are developed from corresponding infinite population moments using the finite probability operator defined in part 1 of this series.

Jan 1, 1964

By H. Akbari

Ordinary portland cement (OPC) is the key pozzalonic component of the concrete mix widely used as a construction material worldwide. B illions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of C O2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic C O2 emissions each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon footprint of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the nonmetallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned extracting some of the valuable metal oxides from fly ash prior to using the major nonmetallic portion of the fly ash for geopolymer concrete application. The results obtained from this study showed that the compressive strength of geopolymer concrete compares favorably with that of conventional concrete prepared using OPC.

Dec 1, 2013

Duty on Lead Reduced. -On December 28, the President signed H.R. 5047 which reduces the duty on unwrought lead from 3.5% ad valorem to 3% ad valorem, with a floor level of 1.0625 cents per pound, effective retroactively from January 1, 1980, through June 30, 1983. Pacific Northwest Power Bill Passed. -On December 5, the President signed S. 885 which will enable the Bonneville Power Administration to guarantee 20-year contracts to its 15 major industrial customers in exchange for higher rates. In effect, the bill will have industrial customers pay some of the costs of building additional generating facilities in the Northwest, of which thermal units are expected to be a major part. BPA supplies power to six primary aluminum producers which operate eleven plants having over 30% of the primary aluminum capacity in the United States.

Jan 1, 1980