Search Documents

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970's (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird's -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

By V Poizat

In different parts of the world the term epithermal is commonly used for a variety of deposit styles. Using the redox state of the ore-forming fluid (inferred from mineralogy and alteration), the metal assemblage of deposits, and other characteristics, at least five different styles of epithermal deposit can be distinguished. Most of these different deposit styles appear to be related to magmatic fluids, with differences resulting from different compositions of source magmas. The most common style of epithermal deposit (low-sulfidation gold-silver deposits associated with calc-alkaline volcanic rocks) remains the most difficult to explain; the metals in these deposits may be derived by basement leaching without magmatic input, or they may come from magmatic volatiles, with contaminated I-type or S-type magmas as the most likely source.

Jan 1, 1995

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

It is possible to divide industrial minerals into four general categories: 1. fuels, 2. construction materials, 4. agricultural minerals, and 4. industrial minerals. It is proposed to ignore the fuels in the context of this paper and deal in general terms with the others. Mining companies have often considered getting into the industrial mineral business because they can see a resource development with good growth and consistent profits. However, many mining companies being conversant with the metallic side of the industry have spent sleepless nights determining which industrial minerals are most suited for their particular situation. Some have got into the business for the wrong reasons and wished they had never heard of it. Others have successfully adapted to the industrial minerals philosophy and now operate in both metallic and industrial mineral arenas. There is a large difference between firstly, the philosophy and secondly, the functions of being in the industrial minerals business as opposed to metallicÆs. The philosophies can be considered in parallel but it is necessary to clearly have an appreciation of the dominant influences that affect industrial minerals.

Jan 1, 1984

Water Balancing in Mineral Processing - Issues and Opportunities

Sep 13, 2010

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009

By William H. Lewis

Energy Research Corp., under contract to the Bureau of Mines, has developed a new miners' caplamp battery. The new battery is based on nickel-cadmium technology and offers significant improvements in performance with reduced size and weight when compared to the conventional lead-acid battery presently in use. This report describes the design and fabrication of the nickel-cadmium battery, which utilizes a roll-bonded electrode structure. The final battery design has a 15-A-h capacity in a 2-112-lb package, which is over 2 lb lighter than the present lead-acid caplamp battery.

Jan 1, 1983

By Gavin C. Dirom

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008

Human-caused global warming has become the environmental cause celebre of the early 21st century. The strong warming alarmist camp currently includes the United Nations, most Western governments, most of the free press, many large corporations (including Enron, before it failed), the major churches, most scientific organisations and a large portion of general public opinion. This phalanx of support notwithstanding there is no scientific consensus as to the danger of human-induced climate change. There is, therefore, a strong conflict between the level of public alarm and its scientific justification. How can this be? In a democracy, the media serve to convey to the public the facts and hypotheses of climate change as provided by individual scientists, governmental and international research agencies, and NGO and other lobby groups. In general, the media have promulgated an alarmist cause for climate change; they have certainly failed to convey the degree of uncertainty that is characteristic of climate science, or a balanced summary of the many essential facts that are relevant to human causation. Climate change is as much a geological as it is a meteorological issue. Natural climate changes, both warmings and coolings, are indeed a societal hazard. We usually deal with geological hazards by providing civil defence authorities and the public with accurate, evidence-based, general information about events like earthquakes, volcanic eruptions, tsunamis and floods, and then by adapting to the effects when a damaging event occurs. As for other major natural disasters, the appropriate preparation for extreme climate events is to mitigate and manage the negative effects when they occur, and especially so for dangerous coolings. Attempting instead to æstop climate changeÆ by reducing human carbon dioxide emissions is a costly exercise of utter futility. Rational climate policies must be based on adaptation to dangerous change as and when it occurs, and irrespective of its sign or causation. The issue now is no longer climate change as such, the reality of which will always be with us. Rather, the issues are, first, the failure of the free press to inform the public about the true facts of human-caused climate change and of the dangers posed by natural climate change. And, second, the vested interests held by many of the groups of warming alarmists. These interests include not only the obvious commercial ones, but also the many scientists and science managers who have discounted or remained silent about the huge uncertainties of the human-caused global warming hypothesis because it suited them to do so. Public opinion will soon demand an explanation as to why experienced editors and hardened investigative journalists, worldwide, have melted before the blowtorch of self-induced guilt, political correctness and special interest expediency that marks the sophisms of global warming alarmists.

Jan 1, 2007

By Anthony H. Tawil

Modern, high-speed machines used in the manufacture of paper require foundations with stringent settlement constraints. To fulfill this requirement, caisson piles, extending into bedrock, were selected to support a paper machine in Baie Comeau for the Quebec North Shore Paper Company (QNSPCo.). This was the fourth machine in an existing paper mill, and its construction was part of an expansion program which included the building of associated structures such as a wood room and chip storage building, and other facilities, Figure 1. The paper mill in Baie Comeau, Quebec, is located in an area which has extensive deposits of sensitive marine clay which are transformed into a viscous liquid when disturbed by external forces such as the driving of piles. Loss of ground and soil disturbance as affected by piling activity assumed considerable importance in the design and construction of the caissons particularly in view of the proximity of existing plant facilities, including another paper machine.

Jan 1, 1987

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

By R. G. Peluso

Methods and results of studies to determine friction and shock losses encountered in auxiliary face ventilation systems utilizing flexible, spiral-reinforced ventilation tubing are presented. The results, tabulated in graphic form, simplify fan selection and enable mine operators to design adequate auxiliary ventilation systems. Problem illustrates the use of graphs.

Jan 1, 1968

By T. O. Glover

The Bureau of Mines surveyed unit trainloading and storage installations in the midwestern, eastern, and southeastern coalfields. Nine individual operations were studied in detail as a representative cross section of unit train operations in these areas. Of the nine operations studied, three were in Illinois, two in Kentucky, and one each in West Virginia, Tennessee, Ohio, and Pennsylvania. Information was obtained from coal producers, coal sale agencies, railroads, construction and equipment companies, and power companies.

Jan 1, 1970

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By Antonio De Biase

In October 2006, a 7m Double Shield TBM, boring through very poor volcanic formations, was pushed back by fluid mud, which presence had not been detected during previous field investigations, due to the high covers characterizing the majority of the tunnel axis. The present work describes the investigations made to gain better knowledge of the conditions in front and all around the TBM, the special measures implemented, the exploratory and bypass tunnels excavated, the extraordinary occurrences came true during the execution of these tunnels, the drainage campaigns, the design of the chamber excavated to free the TBM, the dismounting and restarting of the TBM.

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By Michael Leslie Connor

The paper point out the services of the london metal exchanged on the mining.The investigation is divided at two parts: the tradings sessions and dealing and delivery dates. As well as, the london metal exchanged serves the world metal trade at large in three ways: a daily market price, a physical market and the insurance against market fluctuations.

Nov 20, 1969