Search Documents

By Dachun Liu, Wenlong Jiang, Guozheng Zha, Liang Hu

In this paper, a novel technique for recovery of gallium and arsenic by thermal decomposition under vacuum is presented. The effects of distillation tem- perature on the volatilization behavior of each component were investigated. Theoretical calculations and experimental studies have shown that the method is feasible. The results show that under optimum conditions, highly pure Ga can be extractedwithadvantagesoverconventionaltechniques,includingsimpleoperation andenvironmentalfriendliness.Forexample,metallicgallium(purity > 99.99%)is obtained at 1273 K after 3 h under 3–8 Pa. Arsenic is obtained in the form of a elementary substance which could be preserved with relative ease. (cid:1) (cid:1)

Mar 1, 2018

By Leila Figueiredo de Miranda, Leonardo G. de Andrade e Silva, Anderson dos Santos Mesquita

ThisworkseekstounderstandifPETcompoundswithcarbonblackcan be uses to replace polypropylene and polystyrene for anti-static packaging mate- rials. PETcompoundswerefabricatedcontaining10.0;11.0;12.0and15.0weight % of carbon black with a particle size 325 mesh. We determined the thermome- chanical properties (Dynamic Mechanical Analysis—DMA, Tensile Properties, Fracture Toughness, and Hardness) and Electrical properties of the compounds. In conclusiontheresultsshowthecompoundbased onPETfilledwith 15.0% carbon black might be used in the handling, transportation and storage of electronic components because their mechanical properties, thermal and resistivity are satis- factory for this purpose. (cid:1) (cid:1)

Mar 1, 2018

By J. A. S. Tenorio, A. B. Botelho Junior, I. A. Anes, D. C. R. Espinosa, M. A. Caralho

Recovery of metals from reserves with low grade and from waste with high presence of contamination is a challenge to be overcome. Metals like nickel, cobalt and copper could be recovery from nickel laterite leach waste by many different processes. Among recovery processes that could be applied are ion exchange, solvent extraction and precipitation. The aim of this work was recover copper from liquor of nickel laterite by precipitation using chemical reduction. Copper concentration in liquor was 146 mg L −1 and reducing agent used was sodium dithionite 1 mol L −1. Influence of stirring speed was studied between 0–200 rpm. Results indicated a selective precipitation of copper on solution with others metals at 240 mV. The analyzes were conducted in SEM, energy-dispersive X-ray spectroscopy and XRD, that indicated presence of copper and sulfur.

Mar 1, 2018

By Haibin Wang, Baojun Zhao, Xueyi Guo, Zhixiang Cui, Zhi Wang

In conventional copper production, anode copper is produced from concentrate in three furnaces in a process that entails four oxidation steps and one reduction step. Three types of slags are produced that require further treatment to recover copper. Dongying Fangyuan Nonferrous Metals recently developed a simplified process which requires only two custom-designed furnaces instead of the conventional smelting, converting and re fining furnaces. The first furnace continuously produces high-grade matte (>75 wt% Cu) that contains little iron (<2 wt% Fe). The liquid matte is continuously fed to the second furnace, which produces anode copper. The new process signi ficantly reduces the capital and operating costs and increases productivity and environmental sustainability. This paper presents fundamental concepts that enable the simpli fied process to be developed. The detailed operations in Dongying Fangyuan Nonferrous Metals are also described.

Mar 1, 2018

By Yeole Shivraj Narayan, Nunna Nagabhushana Ramesh, Banoth Balu Naik, Alluru Ramya

MicroEDM process is mainly used for producing miniaturized features like microholes on different types of materials that are hard to cut and difficult to machine. One typical application of microEDM process is microhole drilling operation. Choice and utilization of optimum pulse parameters is of utmost importance for achieving superior surface quality and higher machining rates. However, the process is characterized by low machining rates and considerable overcut as compared to conventional EDM drilling. An attempt is made to investigate the effect of pulse parameters on maraging steel 300 alloy during micro EDM drilling. Parameters like pulse on time, pulse off time, voltage and current are explored through 09 experiments replicated thrice using Taguchi method. Machining characteristics like material removal rate and overcut are studied while drilling micro holes of 500 µm diameter using brass electrode. Evaluation of microhardness after microdrilling is also performed. It is found that puls on time and current influenced the machining characteristics. Minimal change is observed int he microhardness of the alloy after microdrilling.

Mar 1, 2018

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. de Assis

Jute fibers are among the lignocellulosic with great potential for use in polymer composites. In this work, polyester matrix composites incorporated jute fabric were investigated for their flexural behavior. Specimens with up to 30% in volume of jute fabric were bend-tested until rupture. The results showed an increase in both the composite mechanical strength, principally to a polyester composite reinforced with 30% in volume of jute fabric. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the jute fabric and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.

Mar 1, 2018

By S. N. Monteiro, N. A. Cerqueira, E. B. Zanelato, J. Alexandre, M. T. Marvila, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

Mortar is a widely used building material and has its application in buildings in extremely vulnerable environments and susceptible to degradation, such as facades. The objective of this work was to evaluate the loss of mechanical resistance to compression and flexure and the loss of mass of the mortars with effluent sludge from paper industry, when exposed to saline environments. The specimens were done with 0, 5, 10 and 15% of incorporation in lime paste and subjected to saline mist equipment that sprays salt solution in cycles simulating natural degradation conditions using literature data. It can be concluded that mortars with a15%incorporation obtained a significant loss of mass and a decrease in their mechanical resistance, which impairs their use in civil construction and influence in other properties of the material, with a level of incorporation of 10% the results within Brazilian standards.

Mar 1, 2018

By Ian Buterbaugh, Calvin Lo, Tomoko Sano, Brendan Koch, James Catalano, Timothy Walter

In this research, two grades of alumina, one at nominally 85% composition and the other at 99.5% were characterized. Microstructural and phase characterization was conducted using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, X-ray Diffraction, and micro-computed X-ray tomography. It was determined that the Knoop hardness values were influenced by the porosity in the 85% composition. Quasi-static compressive tests and high strain rate compression experiments were conducted to determine the influence of the microstructure to the compressive properties. It was observed that the overall compressive strengths increased with strain rate. Although the Knoop hardness values were much lower in the 85% alumina due to the porosity, the compressive strength at both quasi-static and dynamic strain rates were not significantl lower than those of the 99.5% composition.

Mar 1, 2018

By Ahmet Haxhiaj, Bajram Haxhiaj

Based on the placement of lead and its consumption in industry branches, the paper deals with the composition of lead in the massive of Kopaonik. Removal, tenuity and grinding of galenit. The paper in particular treats the flotation process, and also treats physico-chemical bases of reagents in the process, as well as decanting, drying, filtering and storage of concentrates. Verification of the chemical composition of Pb concentrates with Pb, Zn, Bi, As, Sb, In, Au, Ag, etc. It is special that in Kopaonik massive the ratio of Pb: Zn composition is 1.4:1.0 and during the flotation lead is inclined to go with pirotines concentrate more than is allowed. We are strongly focused to maximally decrease the Pb amount that goes with pirotine concentrates and wastes. The paper as such gave the first effects in optimizing of these parameters with positive effects in flotation process in Trepca.

Mar 1, 2018

By Jinsheng Wang, Xueming Lv, Wei Lv, Junyi Xiang, Xuewei Lv, Chenguang Bai

In this study, microwave heating was used to dry the nickel laterite which contains plenty of free water, crystal water and hydroxy water. The results showed that compared with the conventional drying process, the microwave drying greatly improved the drying efficiency of nickel laterite. The whole microwave drying process can be divided into three stages according to the drying rates, namely, the rising stage, stable stage and declining stage. The effects of microwave power output and particle size were also studied in the range of 0.8–2.0 KW microwave power and 3–6 cm of particle size. The results showed that the drying time significantly decreased with the increase of microwave power and decrease of particle size. The phases transition of the sample during the microwave drying process were also discussed.

Mar 1, 2018

By Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial ofthe detoxification ofchromium slag in cyclonefurnace and the preparation of glass-ceramics were investigated in a power plant in China. 10wt.%chromiumslagweremixedwithpulverizedbituminouscoalandlimestone as the raw materials of the cyclone furnace. Cr(VI) in chromium slag was reduced toCr O insidethecyclonefurnace.Themeltwaswater-quenchedintofritandthen 2 3 fired into glass-ceramics with a laboratory ceramicrollerkiln. The preparation and crystallization behavior of glass-ceramics were investigated with differential ther- mal analysis (DTA), physical and mechanical properties testing, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The optimal flexural strength exceeding 90 MPa were achieved in firing temperature zone of 1170–1200 °C. Anorthite (CaAl Si O ) and diopside [Ca(Mg, Fe)Si O ] can be identified in the 2 2 8 2 6 glass-ceramicsandCaAl Si O isthepredominantcrystalphase.Fineparticleswith 2 2 8 average diameter of 200 nm distributed uniformly in the glass-ceramics. Granular crystals are intensively interconnected and constituted a crystal skeleton soaked in theglassmatrix.LeachingtoxicitytestdetectedCr(VI)of0.016and0.010 mg/Lof the water-quenched frit and glass-ceramics, respectively. This method provides an effective and comprehensive technique for the detoxification and utilization of chromium slag at low cost and large-scale. (cid:1) (cid:1)

Mar 1, 2018

By Jiongtian Liu, Guihong Han, Shuzhen Yang, Yanfang Huang

Binder, as a necessary functional material of electrode in lithium ion battery, has a vital influence on the electrochemical performance. The humics, coupled with polyacrylamide (PAM) and sodium carboxymethyl cellulose (CMC), were used as a water-soluble binder for LiFePO4 (LFP) cathode using in lithium ion battery. The techniques of cyclic voltammetry (CV) and galvanostatic charge-discharge were conducted to evaluate the performance of humics binder in LFP electrode. The reversible specific capacity of LFP (HA + PAM + CMC) electrode can reach to 142 mAh g−1 after 50th cycling (100 mAh g−1) on conditions of raw materials with 1 wt% PAM addition, humics and CMC with a mass ratio of 3:1 in binder, and the raw materials mixed in an interval order. Humics has the potential to be used as a novel, eco-friendly and high-efficient binder for lithium-ion battery.

Mar 1, 2018

By Manuela Castaneda, Henry A. Colorado

This paper is about the use and stabilization of iron oxide based powders with arsenic contents coming from the purification of water. Cement paste samples with 0.0, 2.5, 10 and 20wt% of waste were fabricated by mixing mechanically all components. There are two main positive impacts of using this waste, first, this waste is produced in large amounts worldwide, and therefore the stabilization has a significant impact for the environment. Second, the waste can be used as an admixture and filler for cement, and therefore reduce the amount of cement in the concrete, which has a major impact in the CO2 footprint since cement industry produces a lot of this gas. Compressive strength and density tests were tested after 28 days. Microstructure was analyzed with scanning electron microscopy and x-ray diffraction. Results show that compressive strengths greater than 20 MPa were obtained and the samples had calcite, portlandite and ettringite phases.

Mar 1, 2018

By Marcel Magnusson, Guozhu Ye, Pekka Vaananen, Yang Tian

The most used technology for recycling of spent alkaline batteries consists of crushing, magnetic separation and processing of the nonmagnetic fraction, black mass, using a rotary kiln. In the process only zinc is recovered and all manganese in the black mass is lost. According to the EU regulation for recycling of batteries, more than 50% of batteries should be recovered. To meet the demand, Swerea MEFOS has together with a major battery recycler IsoLogistics in Finland and Sweden developed technologies for efficient recovery of zinc and manganese aiming for >50% recovery. This paper will focus on a treatment process using a DC furnace to produce a ZnO- and a MnO-product. The process has been demonstrated in pilot scale, 1 ton/h. The major outcomes will be highlighted. Another approach by using thermal vacuum technology for distillation of zinc metal has also been demonstrated in laboratory scale which is also reported in this paper.

Mar 1, 2018

By Guozhi Lyu, Ting-an ZHANG, Biyu Long, Yajing Tian, Xuejiao Cao, Weiguang Zhang

Aim to the separation problem of high concentration V–Fe in stronger acidic leaching solution of vanadium slag, a novel chelating extraction system is proposed to separate V and Fe. Influence factors including initial pH value, the extractant concentration, the phase ratio, temperature and time are investigated. The experiment results show that single extraction rate of V and Fe reach 85.57 and 0.39% respectively, when pH value is −0.4, organic phase composition is 30% Mextral 973H + 70% sulfonated kerosene oil, O:A = 1:1, stirring time is 10 min, extraction temperature is 30 °C. The industrial experiment results of three levels countercurrent extraction show that the total extraction rate of vanadium and iron can reach 97.44 and 0.23%, separation factor is 6410. The effective separation of V and Fe in high acid and high iron solution can be accomplished.

Mar 1, 2018

By Wufeng Jiang, Jiann-Yang Hwang, Suju Hao, Yuzhu Zhang

Magnetite powder and coke powder were used as experimental materials and H2 as reducing agent in a high temperature vacuum tube furnace. The change rules of magnetite powder (MP), mixed coke powder and magnetite powder (MCMP), and carbon coated magnetite powder (CCMP) in the process of reduction were studied. The samples were determined by field emission scanning electron microscopy and X-ray diffraction. The results show that, with the increase of reduction time, the reduction degree of magnetite powder is improved. Under the same reduction conditions, the addition of coke powder improves the reduction rate. Compared with MP, when the reduction time was 120 min, the reduction degree of MCMP was 30% greater; and the reduction degree of CCMP was 39% greater. The mixed grinding of magnetite powder and coke powder is a better way to add carbon. Under the same reduction conditions, compared with MCMP, the reduction degree of CCMP was 9% greater when the reduction time was 120 min. After the reduction of CCMP, the number of pores in the sample increased and the structure was loose. The results of this study have some reference value for improving the reduction rate of magnetite powder.

Mar 1, 2018

By Chen Qizhou, Wang Yun, Zhu Rong

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Jun Li, Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial of direct modification of molten blast furnace slag and production of high acidity coefficient slag wool fibers were investigated nearby a blast furnace. Molten blast furnace slag discharged from blast furnace and then directly flow into specialized modification furnace and quartz was simultaneously added into the molten slag as modification agent. The modified molten slag was electric heated to 1500–1550 °C and then the melt was produced into slag wool fibers through high-speed centrifugation method. Melt with acidity coefficient of 1.2, 1.4, 1.6 and 1.8 were investigated and fibers with corresponding acidity coefficient were produced. Slag wool fibers with shot content of 5.5, 5.8, 6.2, 6.8% and average diameter of 4.5, 4.9, 5.6, 6.4 lm for four samples were successfully produced, respectively. Total energy consumption and production costs decreased by 50–70% compared to traditional cupola furnace method. This method provides an energy-saving and emission-reduction technology for the direct utilization of molten blast furnace slag.

Mar 1, 2018

By Guihong Han, Wei Wang, Chaolei Lv, Yongsheng Zhang

Silica aerogels are promising in many applications because of their excellent properties. However, the real applications of pure silica aerogels are limited because of their fragile network structure. We have prepared silica aerogel composites using humic acid as a composite material for improving the performance of silica aerogels and valorization of humic acid. The silica hydrogel composite was prepared using sodium silicate as a precursor and humic acid as a composite material by acid-base catalysis and sol-gel method. The hydrogel was followed by freeze-drying to obtain composite aerogel. The microstructures, specific surface area, and functional groups of silica and composite aerogel were characterized using scanning electron microscope (SEM), brunauer-emmett-teller (BET) and fourier transform infrared spectrometer (FTIR). The results demonstrated that the specific surface area of the silica composite aerogel was 307 m2/g under the condition of pH at 6, the mass ratio of silicon to humic acid (HA) at 3.82 and the molar ratio of N, N-dimethylformamide (DMF) to silicon at 0.9. X-ray diffraction (XRD) showed that the silica (composite) aerogels were amorphous. Thermogravimetric analysis (TGA) revealed that the silica aerogels lost weight from 150 to 250 °C and humic acid decomposed between 350 and 500 °C, and then the mass of the sample remained stable.

Mar 1, 2018

By Keiji Watanabe, Hiroyuki Tobo, Yasutaka Ta, Hisahiro Matsunaga

Recently, effective utilization of by-product slag as aggregate for concrete has been expected from the viewpoints of depletion of natural crushed stone and suppression of environmental loads. We developed a new process for continuous solidification of blast furnace slag as coarse aggregate. In this process, molten slag is continuously poured into molds, and the slag is solidified at the thickness of 20–30 mm. The flow rate of the molten slag is 1 t/min, and maximum production per ladle is about 30 t. After solidification, blast furnace slag coarse aggregate (BFG) is produced by crushing and adjusting the particle size of the solidified slag. The new BFG has water absorption of less than 1%, and concrete containing the BFG has the same fresh property and compressive strength after 28 day as concrete using natural crushed stone aggregate.

Mar 1, 2018