Search Documents

By A. A. Bustos

Four Air Liquide Shrouded Injectors (ALSI ) were installed and operated for over one year in a Peirce-Smith converter at the Falconbridge nickel smelter in Falconbridge, Ontario, Canada. A shrouded injector consists of an inner pipe and an annulus, through which high oxygen enriched air and nitrogen flow, respectively The nitrogen cools the injector and protects the refractory in the vicinity of the injector tip, allowing for substantial increases in oxygen flow rates to the converting reactions. Several injector designs were tested to study the effect of changes in the cross-sectional area and changes in the entrance geometry of the annulus. An optimum design would minimize the injection pressure required for a given flow rate to achieve choked flow conditions at the tip of the injector. The operation of the ALSI was simple and did not require any special care or maintenance, either between blows or between converter cycles. In particular, the shrouded injectors did not require punching, as is the case with conventional tuyeres. In terms of refractory performance, the ALSI, operating at 30-40 % oxygen enrichment, were superior or equal to the conventional tuyeres, which operated at 21-23% oxygen. The results of the demonstration program led Falconbridge Limited to implement the ALSI technology on a commercial scale The paper presents the demonstration program results in terms of gas flow rates, accretion formation, punchless operation and refractory wear.

Jan 1, 1999

By Tiruttani Munikamal, Suresh Sundarraj

"A numerical model of the induction hardening process of steel cranks has been developed and the predicted results of temperature and phase distribution during this solid state phase transformation process are verified with experimental data from the literature. This heat treatment process involves heating the crank to the austenitic temperature range followed by rapid quenching in water to harden the surface of the crank. The model has been developed using ABAQUS, commercial FEA software. The formation of martensite, pearlite, and retained austenite phases are modeled and implemented through a user defined function in ABAQUS. A sensitivity study on the various process parameters affecting the amount of phase distribution has been carried out.IntroductionThe type of surface and sub-surface microstructure as well as the residual stresses that are present in a component after manufacturing, significantly affects it fatigue performance. The wear resistance of the automotive components such as crankshaft, gears, camshaft and bearings depends on the surface hardness. In order to achieve the surface hardness, these steel components are subjected to a type of quench hardening heat treatment process. There are several heat treatment processes available for the industrial application to improve the mechanical properties of the final part. Case hardening using induction heating is one of the widely used industrial techniques for improving the surface microstructure of a steel component. It consists of two stages i.e. induction heating cycle, followed by quenching in a fluid medium (usually water or oil)"

Jan 1, 2012

By F. Begazo

The most common approach to increase production in copper refineries is to increase current densities. However, if these increases are not well thought out beforehand and are not properly and effectively controlled, the end results could be reduced plant performance and a deterioration in cathode quality. Both of these factors result in lower efficiencies and increased costs. At the Ilo Refinery of Southern Peru Copper Corporation, a modernization and expansion program was implemented shortly after the Refinery was purchased from Minero Peru, in 1994. This program was intended to increase production from 195,200 mtpy of cathode to 227,000 mtpy over a 3-year period. Part of this production increase would come from increasing current density. During the period from 1994 to 1997, current density at the Ilo Refinery was increased from 218 A/m2 to 230 A/m2, while plant efficiencies were maintained at consistently high levels. The current efficiencies were maintained at >97.5% and time efficiencies were maintained at >98%. During 1998, additional increases in current density were implemented while the high plant performance was maintained at the same levels. By the end of 1998, the current density was 241 A/m2, while current efficiency and time efficiency of 98% were maintained. This paper describes the control processes used at the Ilo Refinery to maintain high plant performance levels while increasing the current density. Additionally, expected plant performances from extended test programs at current densities up to 280 A/m2, for future production increases, are reviewed and discussed.

Jan 1, 1999

By Ian Masters, Saul B. Davies, David T. Gethin

The purpose of this model is to simulate and analyze the energy flows within a rotary aluminum recycling furnace, using the global properties of its main components, the gas, metal and refractory walls. The model will simulate a series of operations such as loading, heating and stirring which will constitute the processing of a batch. Each main component of the furnace is treated as a one-dimensional heat transfer medium, the thickness and area of each medium being calculated from the actual geometry of the furnace. The physical properties are taken as the weighted average of those for the various layers forming the medium. Incorporated into the model are elements describing the radiative exchange within the furnace, melting of the charge, and forced convection in the melt due to the rotation of the furnace. This approach has produced a model with a reasonable computing time that can be used to run a whole series of simulations for the prediction and comparison of the furnace performance under different operating conditions.

Jan 1, 2000

By G. Riverin, C. Simard, W. D. Stevens

"An on-line technique to measure the efficiency of decoating I delacquering processes is being developed by Alcan' s Arvida R & D Centre. Decoating processes are used to remove moisture and coatings from shredded coated material such as Used Beverage Containers (UBC) before melting. Complete removal has been demonstrated to maximize metal recovery. Quantifying the weight of carbon and organic residue adhering to the shred surfaces is very difficult to measure directly, as the material can be highly folded. The technique developed indirectly measures the residue remaining by analysing the concentration of CO evolved in the decoater end zone exhaust gas.A commercial CEMS (Continuous Emission Monitoring System) incorporating an infrared type CO gas analyser was modified for on-line process exhaust gas analysis. Both pilot and plant trials had demonstrated that the CO concentration measured was inversely proportional to the efficiency of the organic removal achieved. As the quality of coated purchased scrap can be highly variable in moisture and organic content, continuous measurement should permit adjusting the feed rate and other decoater process parameters to the quality of decoating required."

Jan 1, 2000

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of octamolybdate ion in aqueous solution appearing in the literature, a new method for the establishment of corresponding relation between Raman spectral pattern and chemical components of aqueous molybdate solution was put forward using spectroscopy measure and component analyses of saturated solution of ammonium octamolybdate hydrate known structure. It was found that the main characteristic of Raman spectral pattern of the saturated solution was described as the same ?double-peaks, hereinto a weak peak at the boundary? as some literature, but chemical components of the saturated solution were affirmed to be octamolybdate ion (Mo8O264-) and double protonated heptamolybdate ion (H2Mo7O244-), which were in equilibrium in aqueous solution each other. The authors propose that the pattern of the saturated solution can be regarded as the standard pattern of primiparous octamolybdate ion during acidified molybdate solution. It is satisfying that the standard pattern is applied to the identification of primiparous octamolybdate ion during acidified molybdate solution.

Jan 1, 2006

By Ali Akbar Mottahedi

It is known for a long time that the reaction of oxygen with carbon, silicon, iron and many other elements is exothermic. The heat of released from these kind of reactions can decrease the time of fusion of iron and steel for metallurgical purposes in the electrical arc furnaces. By decreasing the time of fusion, we increase the rate of process and the amount of production. So, by blowing oxygen in to the furnace, we can reduce the consumption of electricity and save cost. There are many problems in the procedure of the oxygen blowing. In this project, the theoretical aspect of the oxygen blowing and its side effects into the arc electric furnaces are investigated. An oxygen blowing system into the arc electrical furnace of metallurgy department of Machine Sazi factory was also set up. This process reduced the consumption of electricity up to 22% and increases the rate of production, by reducing tap ? to ? tap time up to 15%. In this project; all oxygen blowing systems and its control were set up.

Jan 1, 2006

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Michael J. Nicol

One of the preferred methods for the recovery of gold from refractory gold ores and concentrates involves pressure oxidation in acidic solutions. The main refractory gold-containing minerals are pyrite and arsenopyrite and there is evidence that the presence of even small amounts of chloride can inhibit the oxidation of these minerals and also substantially reduce the recovery of gold. In this paper, the results of a study of the anodic (oxidation) and cathodic (reduction) behaviour of pyrite electrodes in acidic sulfate solutions containing ferric ions at different chloride concentrations and temperatures up to 200oC and pressures of 2000KPa are presented. The electrochemical studies have been complemented by pressure oxidation experiments on a refractory gold concentrate. Results have shown that, as the chloride concentration increases, the anodic reactivity of pyrite is largely unaffected but the rate of the cathodic reduction of iron(III) decreases. The rate of oxidation of a sulfide concentrate and the recovery of gold by cyanidation of the residues decreases at high concentrations of chloride.

Jan 1, 2003

By Mark E. Schlesinger

A substantial database exists for the thermodynamic properties of many antimonide compounds, but these have rarely been compiled or critically discussed. An abbreviated version of a full?scale review of the thermodynamic properties of binary antimonide compounds is presented, focusing on the choice of experimental techniques.

Jan 1, 2006

By Yoshimasa Oda

The tank house of Tamano Smelter has adopted a high current density electrolysis operation applying PRC (Periodic Reverse Current) method and before 1991, it had materialized both high production capacity of 161,000 tons/year and high labor productivity. However, recent rapid rise of Japanese currency in foreign exchange market has urged us to further exert our efforts in reduction of labor cost. In order to achieve this goal of labor cost reduction, we have completed, in 1994, our phase four production expansion project which incorporated significant re-structuring of the organization and we have accomplished annual production of 191,000 tons/year. This project can be outlined as increase of number of cells for electrode exchange per day in the commercial electrolysis process to meet the increased number of cells and increase of the capacity of impurity treatment process. These improvements were done with minimum installation of new equipment and facilities and with achievements in efficiency and manpower saving of the existing facilities. Together with these improvements, rationalization in the starting sheet section was carried out by changing the material of mother blanks as well as changing their maintenance procedures. At the same time, the crane in this section was modified to enable automatic operation by a fuzzy control. As a result, we were able to save manpower equivalent to 5 operators in this section. With these improvements, the production capacity was increased by 18% and labor productivity by 25%.

Jan 1, 1996

By C. Anderson

Most applications of copper metallurgy are geared towards primary production. However, as recycling of materials is a growing industry, one future facility will rely on copper metallurgy as a means of processing precious metals. This paper will discuss the derivation of the proposed copper pyrometallurgical and electrometallurgical unit operations to be utilized in industrial recycling of secondary precious metals.

Jan 1, 1999

By M. L. Free

Electrowinning is directly impacted by many parameters that include electrolyte composition, voltage, current density, contact resistance, temperature, electrode spacing, and fluid flow as well as many other interrelated factors. The effects of these parameters are primarily related to thermodynamics, mass transport, and electrochemical kinetics. In this study thermodynamic, mass transport, and electrochemical kinetic equations are simultaneously solved to determine the effects of such parameters on electrowinning current efficiency, power consumption, electrodeposit morphology, and electrodeposit distribution. Modeling predictions will be compared with experimental results.

Jan 1, 2006

By Michael L. Sorokin

The metallic nickel production by converting of nickel matte is analysed from the thermodynamic point of view using earlier developed thermodynamic models for sulphide, metal and slag phase. Three-suffix Margules equations are used to calculate thermodynamic properties of melts. Potential diagrams of Ni-FeS-OSiO2 system are calculated for various temperatures and Fe to Ni ratios. The diagrams used for consideration about possibilities of the direct one-stage metallic nickel production.

Jan 1, 1995

By Z. S. Wronski

In rapidly solidified Fe-Nd-B permanent magnet alloys, the content and distribution of Nd-rich intermetallic and Fe-phases determine coercivity Hc and remanence Br. Consequently, microstructure plays a crucial role in deter- mining the (BH) max-product of permanent magnets fabricated from these alloys. A study has been initiated to investigate changes in microstructure and the effects on magnetic properties as the material is processed from arc-melted ingot to melt-spun flakes and finally to a product consolidated by hot-forming. Anisotropic magnetization behaviour has been observed in rapidly solidified flakes after low-temperature annealing.

Jan 1, 1989

By L. A. Barta

A new process for the leaching of chalcopyrite concentrates has been developed and tested in miniplant campaigns and locked cycle testwork carried out between 1996 and 1999. The process involves pressure leaching in a sulphuric acid solution, e.g. raffinate from copper solvent extraction. Iron in the feeds is precipitated predominantly as hematite in the autoclave, simultaneously with copper extraction. Gold and silver in the pressure leach residue are recoverable by conventional cyanidation, following flotation to remove elemental sulphur by-product. The results of recent miniplant tests and batch locked cycle tests are provided.

Jan 1, 1999

By P. Ruz

A melt transfer ladle was 3D modeled by means of a mathematical fluid dynamics and heat transfer program. Internal temperature profiles were calculated as a time function for a normal ladle and for a pre-heated refractory lined ladle. It was shown that in a normal ladle the molten metal cools down quickly forming accretions. By using an inner lining there are practically no accretions build up within a typical time of operation. Therefore, by applying a refractory lining to a melt transfer ladle and keeping it at a moderate to high temperature it is possible to reduce cold dope circulation in the smelter.

Jan 1, 1999

By M. D. Bishop

Loss of organic solvent extraction circuits occurs through several accepted methods. Losses are commonly attributed to entrainment of the plant organic and evaporative loss of diluent. Evaporative losses of diluent have been estimated using various models or by considering all losses over and above entrainment to be due to evaporation. Other possible loss mechanisms are discussed and data on losses during weather conditions are presented. Accurate estimation of evaporative loss is vitally important to the industry due to both cost factors and environmental concerns. Data for and description of the Diffusive Flux Model are presented as an improved-method of estimating evaporative losses:

Jan 1, 1999

By Karel Verscheure

Hydrometallurgical zinc leach residue, EAF dust and other Zn-bearing by-products pose potentially serious environmental problems that threaten the sustainability of the operations. A pyrometallurgical process designed for treatment of such residues is the high-temperature submerged plasma Zn-fuming process. The successful operation of this process requires high Zn fuming rates whilst retaining vessel integrity through stable freeze-lining. A Zn-fuming model has been developed and used to systematically investigate a range of operating scenarios and to identify potential fluxing parameters such as CaO/SiO2, Fe/SiO2, MgO/feed-ratios in the input and fluxing additions of dolomite for maximum fuming rates and stable freeze-lining.

Jan 1, 2006

By S. S. Chabot, S. E. James

A recent survey of major steel companies worldwide revealed the importance of recycling zinc units from electric arc furnace (EAF) dust, mill scale, blast furnace dust and other zinc containing streams within the steel industry. Many processes have been developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and its sale to primary zinc producers to recover the metal values. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of the corrosion problems it will cause in electrolysis. In 1999, Big River Zinc installed a zinc oxide receiving and washing plant to minimize the impact of halides in its electrolysis circuit. A description of the washing plant and the initial operating results are presented in this paper.

Jan 1, 2000