Search Documents

By Jing Zhang, Chenguang Bai, Fusheng Pan

"The microstructure and hot deformation behaviour of an Er-modified Mg-Zn-Ai alloy were evaluated. The results showed that the addition of rare-earth Er changed the morphology of the quasi-continuous grain boundary networked eutectic compound to globular particles. Moreover, a self-strengthening effect was identified for the alloy, which determined its deformation behavior. After hot extrusion, the yield strength and elongation to failure of the Mg-Zn-AI-Re alloy at 200°C were increased by 105% and 120%, respectively, due to an emerged dynamic precipitation strengthening mechanism.IntroductionMagnesium alloys are attracting increasing attention for applications in automobile, electronic devices and hand tools for weight reduction and higher fuel efficiency, because of their lightweight and a high specific strength. However, application of Mg is still very limited. The largest applications are still those non load-bearing castings used at room temperature, such as box case, housing, and covering. One of the main reasons is the inadequate absolute strength both at room temperature and elevated temperatures (> 100°C) of the commercially used AZ, AM series alloys, due to the incoherent interface between the secondary phase y-Mg17AI12 and Mg matrix, as well as the low thermal-stability of the y phase [1]. Besides, the heat-resistant magnesium alloys which contain rare earth (Re) as the main alloying element are very expensive. The other reason is their poor deformability. The key solution is therefore to develop low-cost heat -resistant wrought alloys."

Jan 1, 2012

By Eliezer Martinez-Jimenez, Gretchen T. Lapidus

"Electro-assisted reduction is an effective pretreatment to render chalcopyrite less refractory towards oxidative leaching. In this process, chalcopyrite is selectively converted to chalcocite or copper metal in an electrolytic cell under ambient conditions, while ferrous ion is leached into solution. However, the reaction velocity is hampered by the formation of a ferrous sulfide passivating layer on the solid surface, especially at elevated solid to liquid ratios. In the present work, several strategies for overcoming this problem were evaluated. On one hand, specific ligands for ferrous ion were added in order to increase its solubility and, on the other, an anode material which promotes the oxidation of the sulfide ion was chosen. Leaching tests showed citric acid to be an effective ligand for both ferrous and ferric ions and, in combination with a lead-silver anode, significantly increased the kinetics of chalcopyrite reduction and subsequent copper leaching.IntroductionAttempts to oxidize chalcopyrite at a rapid rate in aqueous solutions, below their normal boiling point, have met with difficulties because of passivation by some of its own components. An alternative line of research explores reductive pretreatment, transforming the chalcopyrite into less refractory copper phases, which can later be oxidized. A recompilation of these efforts up until 2000 was published by Dreisinger and Abed [1]. However, this practice usually requires large excesses of reducing agents, such as copper, lead, aluminum or iron, and in this last case at near-boiling temperatures, in highly"

Jan 1, 2012

By C. Wieckert

Concentrated solar energy can be used as heat source for the production of metals. One of the most promising respective processes, the solar carbothermic production of Zn from ZnO, is investigated within the European research project SOLZINC, a cooperation of institutes and industries from France, Germany, Israel, Sweden and Switzerland. The solar produced Zn can be used as commodity or as an energy carrier for further processing on demand to electricity in Zn-air fuel cells/batteries or to generate hydrogen by reaction with steam. In both cases the Zn is oxidized to form ZnO, which can be recycled back to the solar plant. In these cyclic processes Zn acts as a means to store and eventually transport solar energy. Second product of the solar process step is a CO-rich offgas, which may e.g. drive a gas engine or may be shifted to hydrogen in a conventional reaction with steam. A pilot plant using 300kW concentrated solar power input has been constructed and operated successfully. 86mass-% of ZnO mixed with 14mass-% of charcoal are reacted to produce Zn and CO at a temperature of about 1200°C, yielding about 50 kg gaseous Zn per hour. Zn-dust with 95% purity is recovered from the offgas system that was designed to produce Zn for Zn-air fuel cells. Based on the results and findings from the pilot plant, a two tons Zn/h solar demonstration plant has been designed conceptually. Cost studies have been performed and scenarios for producing electricity or H2 via these ZnO/Zn-cyclic processes are evaluated.

Jan 1, 2006

By Zhang Hengzhong

Ni-P-Fe slag is the by-product in the production of phosphate fertilizer in blast furnace with nickel contained serpentine ore as the raw material. It contains nearly 5-7% Ni, 65-7( Fe, and 10-12% P. The slag is very hard to process, it neither dissolves in aqueous ammonia, nor in sulphate acid. In the stiff the technique to treat the slag in order to extract valuable nickel was developed, it essentially consisted of the processes of roasting, leaching, separation and purification. Nickel sulphate was prepared with this method.

Jan 1, 1993

By Zuomei Jin

A laboratory study was conducted on the separation of Zn, Pb, Cu and Ag from a finely dissem-inated interlocked silver-rich multimetal sulphidc ore. These are often difficult to separate from each other by flotation. The thermodynamic calculations of Zn-S-O, Cu-S-O systems at different tem¬peratures were presented on predominance diagrams. Based on these diagrams the optimum temperature and gas composition were selected for roasting. The results of separating Zn, Cu from calcine by neutral leaching and acid leaching were found to be satisfactory. The distribution of silver in the roasting and leaching processes were tested. A flow sheet was proposed.

Jan 1, 1993

By Mokka N. Rao

In this experimental investigation, the principal operating parameters of the spirals HC 1870 and HG 8/7 are determined for the hydrogravimetric separation of the friable siliceous iron minerals of the Piar Distric, Venezuela. Mineralogical characterization including optical microscopy of feeding materials and the products after separation are presented. Comparative analysis is made of effectiveness of productivity between the two spirals.

Jan 1, 1999

By J. R. Budden

The growth and oxidation characteristics of any bacterial culture are ultimately determined by the nature of the sample being treated. The most important parameters in the application of bio-oxidation are bacterial cell number, growth rates, oxygen uptake and rate of oxidation. Cells present in the solution of an established culture were counted directly using a microscope, related to a protein value, and then used to determine the total cell number (in solution and on the solids). Protein determination of total cells enabled the growth rates on slurry to be calculated. The cell number and culture growth is related to the iron and sulphide contents of the sample. To illustrate these considerations a moderately thermophilic culture was used to treat ore and concentrate samples obtained from Australian mines.

Jan 1, 1990

By Oleksandr Liaskovskiy, Sergey Beringov, Sergiy Yatsuk, Timur Vlasenko, Iryna Buchovska

"Working with solar-grade silicon for solar cells application usually meets some difficulties in comparison to polysilicon produced by Siemens method: higher impurities content leads to lower yield, worse electro-physical parameters and poor performance in solar cells application. However some adjustments in ingot production can show significant improvements in quality of final product: crystalline wafers and cells.Recent investigations have shown that solar-grade silicon is suitable for high effective production process such as mono-like multicrystalline wafer production. Production-scale lots made at Pillar show promising results for solar-grade silicon application: high-quality wafers with significantly big crystalline grains of <100> orientation.IntroductionThe standard technology of producing multicrystalline silicon ingots by directional solidification method in quartz crucibles has a number of disadvantages resulting in limited efficiency of solar cells made of multicrystalline material: crystallites of multicrystalline ingot are relatively small (down to 5 mm size), grain borders of crystallites contain parasitic impurities such as metals, silicon nitride etc., crystallographic orientation of crystallites is random. The listed deficiencies are an integral characteristic of the technology which affects the efficiency of solar cells, such as presence of solar cells with low efficiency even at a high level of average efficiency, problems with shunted cells, silicon nitride inclusions, which adversely affect cell efficiency and are centres for silicon carbide formation, impossibility of application of high effective alkaline texturing etc. Also with regard to the targets set by photovoltaic to reduce the cost per Wp in the nearest future, standard technology of multicrystalline silicon ingots production by directional solidification faces certain challenges some of which are hard to overcome due to rather low efficiency of solar cells made of multicrystalline wafers. Therefore alternative methods of multicrystalline silicon production for photovoltaic application having a number of advantages in comparison to traditional technology are developing rapidly."

Jan 1, 2012

By James D. Navratil

Ferrites have been used to separate a wide range of substances such as dissolved metal species, particulate matter, and organic and biological materials; they have been used almost exclusively for metal waste treatment applications. The versatility of the ferrite waste treatment technique is evident in the wide variety of application methods. Furthermore, ferrites can be used to remove selected impurities in feed solutions containing metal products requiring purification. A brief overview of ferrite properties and recent applications for metal recovery and waste processing will be presented.

Jan 1, 1990

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave dielectric properties of silicon dioxide at frequencies of 915 and 2450 MHz were characterized in the temperature range of 24 to approximately 1000 °C using the cavity perturbation technique. It is shown that the relative dielectric constant of silicon dioxide at both frequencies remains almost unchanged below 500 °C, above which there is a slight increase of 2%. The relative dielectric loss factor of silicon dioxide exhibits a strong temperature dependence above 500 °C and increases by approximately 7 and 5 times at 915 and 2450 MHz, respectively. The substantial increase in the relative dielectric loss factor is mainly attributed to the enhanced dielectric polarization and accelerated electrical transport in silicon dioxide at elevated temperatures.IntroductionSilicon dioxide (Si02) is usually considered a microwave transparent material due to its poor absorption capability at room temperature [1]. This characteristic has led to various applications of silicon dioxide in microwave processing of materials and communication. For instance, Si02 has been used to produce sample holders for microwave heating and substrates for electronic devices [2,3]. These applications generally require the material to withstand high temperatures under microwave irradiation. This indicates that microwave absorption capabilities of silicon dioxide at elevated temperatures are also important for its utilization.The microwave absorption capability of Si02 can be determined based on dielectric characterization (permittivity measurement) of the material at commonly used microwave frequencies, 915 and 2450 MHz, in a broad temperature range. To date, however, no detailed work on the dielectric properties (permittivity) of silicon dioxide at high temperatures has been reported. The present work is aimed to study the dielectric properties of silicon dioxide from room temperature to approximately 1000 °C at 915 and 2450 MHz. The results show that the permittivity of silicon dioxide has a strong temperature dependence above 500 °C, suggesting a substantial increase in its microwave absorption capability."

Jan 1, 2013

By Gjergj Dodbiba, Toyohisa Fujita, Takahiro Kikuchi, I-Chen Wu

"In order to separate molybdenum (Mo) from the high-level radioactive liquid waste (HLLW), Pb-Fe based adsorbents were synthesized. The adsorbents were precipitated by adding sodium hydroxide in mixture of 1 mol/L lead nitrate and 1 mol/L ferric nitrate aqueous solutions. Each precipitate was then filtered, dried and ground to obtain a fine powder, which has been used as an adsorbent. Two main parameters were considered when synthesizing the adsorbents, i.e. the pH value at precipitation of adsorbent precursor and the calcination temperature of Pb-Fe based adsorbent. Moreover, the structures of the synthesized adsorbents were investigated by means of an X-ray diffractometer.The experimental results indicated that the calcination temperature of the Pb-Fe based adsorbent has a great influence on adsorption capacity of the adsorbent for Mo. It was found that when the Pb-Fe based adsorbent was calcinated at 500 oC, the sorbed concentration of Mo was the highest.1. IntroductionThe high-level radioactive liquid waste (HLLW), arising from the reprocessing of nuclear fuel are generally immobilized in an alkali borosilicate glass matrix. Broadly speaking, alkali borosilicate glasses are the matrix of choice for the immobilization of the HLLW, since they permit vitrification of waste stream of variable composition, [1]. Within this frame, the incorporation of molybdenum (Mo) is of particular interest in the vitrification of HLLW. Molybdenum is know to have a low solubility in borosilicate glass compositions and its presence in excess results in the phase separation of a complex yellow molten salt during vitrification, [1]. The formation of so-called “yellow phase” material during the vitrification process is undesirable since it leads to the accelerated corrosion of the inconel crucible liners. Furthermore, the “yellow phase”, which is reported to contain also other fission products, is soluble in aqueous solution providing a potential route for the leaching of radionuclides from the vitrified waste, should it come into contact with water, [1]."

Jan 1, 2008

By Kurt Westerlund

Cooling of hot sticky gases with solids in a circulating fluidized bed called FLUXFLOW is described. Fluxflow is used for gas streams from metallurgical reactors, e.g., Isasmelt copper in Australia and TBRC for lead in Sweden. The features and potential of this technology in metallurgy and waste treatment ie described. The FluxfLow la a new, cost efficient high availability solution to treat hot sticky gases that has made new gas handling and heat recovery flow sheets available to the process industry.

Jan 1, 1994

By Laura Garcia H, Juan Carlos Gonzalez Islas, Luis Garcia Lechuga, Pedro Alberto Ramirez Ortega

"Electrochemical studies were performed to silver recovery from industrial wastes (radiographic films) on litanium flat electrode using a filter press-type electrochemical reactor with vertical orientation (known as REOV-01), as counter electrode was used a mesh-type DSA. Voltammetric studies were employed to fmd the current range under which silver reduction occurs. Using chronopotentiometric studies with controlled current, homogeneous deposits were obtained on the surface of the Ti electrode, to a current of -210 mA during 120 minutes to a constant linear flow velocity of 15 Lmin-1 was achieved 97% of silver recovery from industrial wastes. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy studies corroborated the presence of silver on Ti flat electrode. In addition, the silver concentration in the solution after the experiments was 1 ppm below environmental requirements. This indicates the viability of a filter press-type electrochemical reactor with vertical orientation (REOV-01) for silver recovery from radiographic filmsIntroductionIn recent years, the industrial sector has shown an increase in the use of silver due to new applications in different areas. In sectors such as photography, the consumption of silver has declined as a result of the boom in digital photography. However, the use of silver in radiographic applications has not shown greater variation (47.16 Moz), as the image quality is essential for diagnosis in various fields, such as medicine. All the silver used in photographic applications is discarded completely (solid or in effluent). At the present, several countries have been involved in silver recovering from industrial wastes due to the economic value and environmental impact they represent. The main source of silver recovery is the wastes generated by the photographic sector. Various technologies have attempted to recover silver contained in these wastes. However, they have not fully satisfied the requirements of maximum recovery, nor environmental level (less than 5 ppm) of silver in effluents [1,2]."

Jan 1, 2014

By Natasa Mitevska

The distribution coefficients of Ag, As, Au, Bi, Co, Cu, Ni, Pb, Sb, Se, Te, and Zn between copper matte and slag from the reverb furnace No.2 at the Copper Smelter and Refinery, RTB BOR (Yugoslavia), are presented in this paper. The influence of the matte grade on the minor elements distribution coefficients between copper matte and slag is analyzed. The minor elements distribution in the slag phase along the slag melt depth and the furnace length is also determined.

Jan 1, 2002

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By James Douglas

A century ago the AIME meeting of 1899 was held at the Palace Hotel in San Francisco California in September. For his presidential address, James Douglas presented this paper which is reprinted in full with the kind permission of the AIME. It presents an interesting comparison relating to events and circumstances in the metallurgical industries at the close of last century. Being on the eve of a new century ourselves, the Editors of this volume of the COPPER 99-COBRE 99 Proceedings considered this paper would be of general interest, hence it is included here. Douglas believed in effective interchange of technical experiences and ideas. He considered the extreme secrecy surrounding the copper works at Swansea, Wales, the world center of copper only years before the time his paper was delivered, as one key reason for its decline, (and eventual closure of all copper plants there). In his paper, the pace of developments in various sectors such as transportation (railroads, the dominant means of I transportation at the time), the iron and steel and copper industries were examined, in much the same way as one might do but on the high technology of today. James Douglas was born in Quebec City, Quebec, Canada and spent his early life there. Forced to move to the United States for family and financial reasons, he went on to become a pioneer in the new Arizona copper industry, and with luck and good judgement with his interest in the new mining properties he also became very wealthy. Douglas was an accomplished mining and metallurgical engineer. He was the first President of Phelps Dodge and helped transform the small trading company of Anson Phelps and William Dodge into a mining giant.

Jan 1, 1999

By B. G. Thomas

"Mathematical process models can be applied in several different ways to serve industry by inducing beneficial changes to process operation. This paper attempts to summarize the different uses, types, and attributes of these models, and to offer some ideas to consider when developing, using, and reporting on them. Process models range from empirical to mechanistic in nature and vary in complexity from simple analytical solutions to coupled, 3-D transient numerical simulations. They are classified here according to the way in which they are implemented in practice, viz. fully-online models, semi-online models, off-line models, and literature models. The purpose of the model should dictate how choices are made during its development. Ways to validate and compare the model with experiments are suggested. Examples are taken in the context of the author's experience in modeling the continuous casting of steel.IntroductionThe objective of this paper is to provide a partial introduction for this symposium by discussing some basic aspects of the application of mathematical process models in industry. Essentially, the aim is to explore how process models are used to benefit industry, and to offer some general comments and suggestions, based on the experience of the author, on how models can best meet this goal.This work is concerned with process models, which consist of systems of mathematical equations and constants that are solved on a computer to make quantitative predictions about some aspect(s) of the process. The specific variables required as input data and generated as output data are important features of the model. The equations often derive from a numerical solution to one or more differential equations and their boundary conditions. The model also includes the constants, which represent material properties, empirical relationships, and other knowledge about the process, and usually require considerable effort to obtain. Thus, general purpose commercial software packages, (ie. finite-element or finite-difference based codes), are not models in this context. They are useful tools, however, serving as frameworks for the development of process models."

Jan 1, 1994

By S. V. Ketov, V. P. Menushenkov, V. S. Shubakov

"The glass samples were obtained by melting of the oxides mixture SrO-Fe2O3-B2O3(Al2O3) at 1200-1250°C with subsequent quenching of the melt on quickly rotating steel roller. Submicronsized Sr(Fe,Al)12O19 particles were formed in glass-ceramic matrix during the crystallization aging of glass. The aging temperature Tag varied in the range 650-950°C. The submicron-sized hexaferrite powder was obtained by removing of the matrix phases using etching. The samples were characterized by X-ray diffraction, scamiing electron microscopy and magnetization measurements. The glass-ceramic material exhibits very high coercivity value up to 10 kOe. The samples of magnets were obtained by pressing of the hexaferrite powder at RT and subsequent aging in the range 900-1200°C. The aged samples exhibit coercivity value up to 8 kOe.IntroductionStrontium M-type hexaferrites have been widely used in technology and industry mainly for production of permanent magnets owing to their appropriate magnetic properties, chemical stability and low cost [1,2]. The SrFe12019-based compounds are characterized by high magnetocrystalline anisotropy and single easy magnetization axis. The highest coercivity is received for monodomain, defect-free single crystal particles with size D - 100 mn. Finely grained strontium hexaferrite prepared by chemical methods such as sol-gel pyrolysis and oxide glass crystallization exhibits high coercivity up to 6-8 kOe [3-5]. Owing to the partial substitution of Al for Fe in the strontium hexaferrite leading to the increase in the magnetic anisotropy field Ha=2Ki/M,, the increase in the coercivity may be received [6]. The notable results were achieved using the SrO-Fe2O3-AlzO3-B2O3 glass crystallization and formation of perfect submicron crystals of alumina-doped hexaferrite [ 6, 7]. The coercive force of glassceramics reached values of up to 10 kOe. Hexaferrite particles are well faceted and have the shape ofhexagonal bipyramids with truncated vertexes [7].In the present paper, we report results of our investigation into the SrO-Fe2O3-B2O3(Al2O3) glass crystallization, hexaferrite powders and permanent magnets, which were prepared by pressing submicron-sized hexaferrite powders at RT and subsequent sintering at 900-1200°C."

Jan 1, 2012

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Alana Pereira Ramos, Walman Benicio de Castro

Amorphization and martensitic transformation (Ms) characteristics of Ti–Ni-Cu alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the wheel linear velocity from 21 to 63 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate and alloy composition on martensitic transformation behavior is discussed.

Jan 1, 2015